铜和铜合金的弧焊工艺评定试件检测

JB/T 4755-2006铜制压力容器

本标准规定了铜制压力容器的设计、制造、检验和验收要求。铜制常压容器亦可参照本标准。1.1 本标准适用于设计压力不大于35MPa的容器。1.2 本标准适用的设计温度范围按铜材及其复合钢板允许的使用温度确定。铜材衬里容器适用的设计温度范围除应考虑铜衬层和钢亮层材料分别允许的使用温度外，还要考虑衬层和壳层材料弹性模量和热膨胀系数的差别。1.3 下列各类窗口不属于本标准的范围：a）直接用加热的容器；b）核能装置中的容器；c）作为旋转或往复运动的机械设备构成部分的受压器室（如离心泵壳、往复泵缸体、压缩机缸体、冷冻机缸体、鼓风机壳、离心机壳与转鼓等）；d）经常手动的容器；e）内直径（对蜚圆形截面，指宽度、高度或对角线，如矩形为对角线、椭圆为长轴）小于150mm的容器；f）作疲劳分析的容器。1.4 对不能用本标准来确定结构尺寸的受压元件，允许用以下方法设计，但需经锅炉压力容器标准化技术委员会评定、认可。a）包括有限元在内的应力分析；b）难性实验分析（如实验应力分析、难性液压试验）；c）用可比的已投入使用的结构进行对比经验设计。

DIN 1900-2010金属材料用铜焊程序的规范和资格.钢的电弧钎焊用程序试验

This standard specifies how a preliminary arc brazing procedure specification is qualified by brazing procedure tests. It applies to steels.

DIN EN ISO 13628-15-2012石油和天然气工业.海底生产系统的设计与操作.第15部分:海底结构和歧管(ISO 13628-15-2011).英文版 EN ISO 13628-15-2011

This part of ISO 13628 addresses specific requirements and recommendations for subsea structures and manifolds, within the frameworks set forth by recognized and accepted industry specifications and standards. As such, it does not supersede or eliminate any requirement imposed by any other industry specification. This part of ISO 13628 covers subsea manifolds and templates utilized for pressure control in both subsea production of oil and gas, and subsea injection services.

DIN EN ISO 15614-6-2007金属材料焊接程序的规范和鉴定.焊接程序试验.第6部分:铜及其合金的电弧焊接和气焊(ISO 15614-6-2006)

This part of ISO 15614 specifies how a preliminary welding procedure specification is qualified by weldii procedure tests. It applies to the arc and gas welding of copper and copper alloys in all product forms.This part of ISO 15614 defines the conditions for the execution of welding procedure tests and the range qualification for welding procedures for all practical welding operations within the range of variables listed Clause 9.This part of ISO 15614 is applicable to all new welding procedures. However, it does not invalidate previot welding procedure tests made to former national standards or specifications. Where additional tests have be carried out to make the qualification technically equivalent, it is only necessary to do the additional tests c a test piece made in accordance with this part of ISO 15614.Additional tests may be required by application standards. The principles of this part of ISO 15614 may be applied to other fusion welding processes.

DIN EN ISO 15614-8-2016金属材料焊接程序规范和资格.焊接程序试验.第8部分:管对管板连接件的焊接 (ISO 15614-8-2016).德文版本 EN ISO 15614-8-2016

The document specifies requirements for the approval testing of welding procedures for the arc-welding of tube to tube-plate joints in metallic materials by manual, semiautomatic, automatic or mechanized processes. It is a part of a series of standards given in ISO 15607. Annex B gives details of these standards. Approval by tube to tube-plate joints tests can be used for all joints even if they are fully loaded or only seal welded as required in application standards.