燃气器具快速切断装置检测

燃气器具快速切断装置检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB 35848-2018商用燃气燃烧器具

本标准规定了商用燃气燃烧器具(以下简称燃具)的术语和定义，分类和型号，要求，试验方法，检验规则，标志、警示和说明书，包装、运输和贮存。本标准适用于以符合GB/T 13611规定的燃气为能源，燃烧用空气取自室内、燃烧产物直接或间接排向室外的燃具，包括：a)　额定热负荷不大于80 kW、蒸汽压力不大于80 kPa，且设计正常水位水容积小于30 L的蒸汽发生器类燃具；b)　额定热负荷不大于80 kW、蒸腔蒸汽压力不大于500 Pa的蒸箱类燃具；c)　额定热负荷不大于50 kW、腔体内压力不大于80 kPa的炸炉类燃具；d)　额定热负荷不大于50 kW的煮食炉类燃具；e)　额定热负荷不大于80 kW、锅口有效直径不小于600 mm的大锅灶类燃具；f)　额定热负荷不大于10 kW的煲仔炉，额定热负荷不大于50 kW的矮汤炉等平头炉类燃具；g)　额定热负荷不大于100 kW的常压固定式沸水器类燃具；h)　焖饭量大于等于6L的饭锅类燃具；i)　额定热负荷不大于50 kW的洗碗机类燃具；j)　额定热负荷不大于60 kW的炒灶类燃具；k)　额定热负荷不大于50 kW的烧烤炉类燃具；l)　额定热负荷不大于35 kW的热板炉类燃具；m)　额定热负荷不大于80 kW的烤箱类燃具；n)　以上产品的组合体。

GB/T 36699-2018锅炉用液体和气体燃料燃烧器技术条件

本标准规定了锅炉用液体和气体燃料燃烧器的分类与型号编制、组成与基本配置、基本要求、性能要求、设计与制造、检验、试验与检测、技术文件与标识、包装、运输和贮存、安装、调试与使用等方面的技术要求。本标准适用于锅炉用液体和气体燃料的强制鼓风燃烧器和自然通风燃烧器。电站锅炉启动燃烧器、各类工业窑炉与工业加热炉及其他用途燃烧器可参照本标准执行。

GB/T 50811-2012燃气系统运行安全评价标准

本规范适用于已正式投产运行的面向居民、商业、工业企业、汽车等领域燃气系统的现状安全评价。本标准不适用于燃气的生产、城市门站以前的天然气管道输送，以及沼气、秸秆气的生产和使用。

CJ/T 113-2015燃气取暖器

本标准规定了燃气取暖器(以下简称取暖器)的术语和定义,分类与型号,结构和材料,要求,试验方法,检验规则,标识和说明书,包装、运输和贮存。本标准适用于使用GB/T 13611规定的燃气的取暖器,包括:a) 额定热输入不大于20 kW的家用取暖器;b) 单个燃烧器额定热输入不大于120 kW的非家用取暖器。本标准不适用于室外使用的取暖器、冷凝式取暖器、专为工业用途设计的取暖器、在移动的运输交通工具中使用的取暖器。

CJ/T 398-2012家用燃气用具电子式燃气与空气比例调节装置

本标准规定了家用燃气用具电子式燃气与空气比例调节装置的术语和定义、缩略语、结构和材料、要求、试验方法、检验规则、标识、安装和操作说明书以及包装、运输和贮存。本标准适用于大工作压力在10kPa以下、公称直径不大于DN50、使用GB/T 13611规定的城镇燃气器具用、闭环控制的能被单独测试或作为燃气用具（或燃烧器）部件进行测试的家用燃气用具电子式燃气与空气比例调节装置。

CJ/T 421-2013家用燃气燃烧器具电子控制器

本标准规定了使用GB/T 13611规定的城镇燃气的家用燃气燃烧器具用电子控制器（以下简称控制器）的术语和定义、分类、结构、要求、试验方法、检验规则、标识、安装和操作说明书、包装、运输和贮存。本标准适用于家用燃气燃烧器具用电子控制器的生产和检测。

CJ/T 451-2014商用燃气燃烧器具通用技术条件

本标准规定了商用燃气燃烧器具(以下简称燃具)的术语和定义,分类,结构和材料,要求,试验方法,检验规则,标识、警示和使用说明书,包装、运输和贮存。本标准适用于商用厨房等使用,以符合GB/T 13611规定的燃气为能源,安装在室内、燃烧产物机械排至室外的燃烧器具。

DB31/T 1011-2016燃气用户设施安全检查技术要求

本标准规定了术语和定义、基本要求、检查内容、记录等内容。本标准适用于居民用户和供气压力＜0.01 MPa的非居民用户使用的燃气用户设施的安全检查。

EN 30-1-1-2008家用燃气灶具.第1-1部分:安全性.一般性;包含修改件A1-2010

This European Standard specifies the construction and performance characteristics as well as the requirements and methods of test for the safety and marking of freestanding and built-in domestic cooking appliances burning the combustible gases given in 4.1 according to the categories specified in 4.2, referred to in the text as \"appliances\".This European Standard covers the following types of domestic cooking appliances, as defined in Clause 3, and belonging to the classes defined in 4.3 (see Table 1): independent freestanding hotplates; independent built-in hotplates; independent hotplates and grills; table cookers; freestanding ovens; built-in ovens; freestanding or built-in grills; griddles; freestanding cookers; built-in cookers. Unless specifically excluded hereafter,This European Standard applies to these appliances or their component parts, whether or not the component parts are independent or incorporated into a single appliance, even if the other heating components of the appliance use electrical energy (e. g. combined gas-electric cookers).This European Standard includes requirements covering the electrical safety of equipment incorporated in the appliance that is associated with the use of gas. It does not include requirements covering the electrical safety of electrically-heated component parts or their associated equipment1).This European Standard does not apply to: a) outdoor appliances; b) appliances connected to a combustion products evacuation duct; c) appliances having a pyrolitic gas oven; d) appliances having covered burners which are not in conformity with the constructional requirements of 5.2.8.2.2; e) appliances incorporating flame supervision devices and having an automatic ignition device for which the duration of the ignition attempt is limited by design; f) appliances equipped with a burner that is periodically ignited and extinguished under the control of an automatic on/off device; 1) Refer to the electrical safety rules. g) appliances equipped with an oven and/or with a grill having a fan: 1) either for the supply of combustion air or for the evacuation of the products of combustion; 2) or for the circulation of the products of combustion within the compartments; h) appliances supplied at pressures greater than those defined in 7.; i) appliances having one or more burners that are capable of remote operation (type1 or type 2), unless the burner(s) concerned are thermostatically controlled oven burners of time-controlled ovens that are designed for a delayed start without the user being present; j) appliances incorporating one or more hotplate or grill burners that enable the user to program the cooking cycle, including the start and/or the end of the cycle.This European Standard does not cover the requirements relating to third family gas cylinders, their regulators and their connection.This European Standard only covers type testing.

EN 88-1-2011燃气器具用压力调节器和相关安全装置.入口压力大为50 kPa及以下的压力调节器

This European Standard specifies the safety, construction and performance requirements for pressure regulators and pneumatic gas/air ratio pressure regulators (zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure regulator), intended for use with gas burners, gas appliances and similar use, hereafter referred to as `pressure regulators'.This European Standard is applicable to pressure regulators with declared maximum inlet pressures up to and including 50 kPa (500 mbar) of nominal connection sizes up to and including DN 250 for use with one or more fuel gases in accordance with EN 437, pressure regulators which use auxiliary energy, pneumatic gas/air ratio pressure regulators, which function by controlling a gas outlet pressure in response to an air signal pressure, air signal differential pressure, and/or to a furnace pressure signal (zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure regulator), gas/air ratio pressure regulators which change an air outlet pressure in response to a gas signal pressure or a gas signal differential pressure.This European Standard does not cover pressure regulators connected directly to gas distribution network or to a container that maintains a standard distribution pressure, pressure regulators intended for gas appliances to be installed in the open air and exposed to the environment, mechanically linked gas/air ratio controls, electronic gas/air ratio controls (EN 12067-2).

EN 1319-2009净加热输入量不超过70kW的带有风扇辅助锅炉的家用空间加热燃气强制对流空气加热器

This European Standard specifies the requirements and test methods for the safety and efficiency of domestic gas-fired air heaters with a fan to assist the transportation of combustion air and/or combustion products, hereafter referred to as appliances.This European Standard applies to Type B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C12, C13, C32, C33, C62 and C63 appliances with an input not exceeding 70 kW (net cv basis), intended primarily for use in single unit residential dwellings. Provision of the heated air may be by means of ducting.This standard does not apply to: a) appliances of the condensing type; b) appliances for outdoor installation; c) dual purpose air conditioning appliances (heating and cooling); d) appliances where the air is heated by an intermediate fluid; e) appliances with forced draught package burners or fully premixed burners; f) appliances fitted with a manual means of adjusting the combustion air supply or the evacuation of the combustion products; g) portable or transportable forced convection appliances; h) appliances having multiple heating units with a single draught diverter; i) appliances fitted with more than one flue outlet; j) Type C22, C23, C42, C43, C52 and C53 appliances; k) appliances that are designed for continuous condensation within the flue system under normal operating conditions; l) appliances having combustion products evacuation ducts, POCEDs, that are non-metallic.This standard is applicable to appliances which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals.

NF D35-354-2008专用液化石油气装置用规范.家用无烟道空间加热器(包括扩散式催化燃烧加热器)

La présente Norme européenne spécifie les prescriptions, les méthodes d'essais et le marquage des appareils domestiques de chauffage non raccordés à un conduit d'évacuation des produits de la combustion, y compris les appareils à combustion catalytique diffusive, dont le débit calorifique nominal est inférieur à 4,2 kW (HS), alimentés par des gaz de la 3e famille sous la pression nominale de service ne dépassant pas 50 mbar, désignés dans le texte par \"appareils\".La présente Norme européenne est applicable aux types d'appareils suivants : appareils fixes fonctionnant au butane commercial et/ou au propane commercial ; appareils portatifs ou mobiles fonctionnant soit au butane commercial, soit au butane commercial et au propane commercial, y compris ceux qui ont un compartiment d'installation pour une bouteille portative rechargeable de gaz de pétrole liquéfié.Aucune prescription particulière concernant le rendement thermique n'est définie pour ces types d'appareils car toute la chaleur produite par le processus de la combustion se dégage dans l'espace à chauffer ; les exigences concernant la combustion, qui relèvent de la sécurité, garantissent la combustion du combustible gazeux.La présente Norme européenne ne concerne pas les appareils incorporant des dispositifs électriques de contrôle du gaz.L'annexe A donne les détails concernant les catégories d'appareils commercialisées dans les divers pays.Les exigences pour les appareils données dans cette norme européenne supposent que l'alimentation en gaz à partir de la bouteille soit contrôlée par un détendeur dont la pression nominale maximale de détente atteint 50 mbar.La présente norme européenne ne concerne pas les bouteilles de gaz de pétrole liquéfié, ni leurs détendeurs associés, ni les tubes et tuyaux flexibles, qui doivent être conformes aux réglementations nationales en vigueur. La présente norme couvre uniquement les essais de type.

NF P45-204-7-2008建筑工程.家用房屋中气体装置.第7部分:计算规则

Le présent document fixe des règles de calcul pour :- dimensionner des canalisations d'alimentation en gaz combustibles et en hydrocarbures liquéfiés des appareils installés dans les bâtiments d'habitation et de leurs dépendances,- dimensionner des systèmes d'évacuation des produits de combustion fonctionnant en tirage naturel des appareils de types B1 et B2 de débit calorifique nominal inférieur ou égal à 85 kW,- dimensionner les systèmes d'évacuation des produits de combustion des appareils installés en alvéoles techniques gaz,- déterminer le nombre admissible d'appareils de type C dont les terminaux débouchent dans les courettes fermées et les configurations en U.Les prescriptions applicables à ces différents cas sont présentées en Annexes A, B et C. Ces Annexes précisent également leur domaine d'application particulier respectif.

DIN 3386-2012大工作压力小于或等于5 bar的空气过滤器.试验和要求

The available standard regulates requirements and examinations for gasfilters up to a nominal size of including DN 250, which operat with gases of DVGW-Arbeitsblatt G 260 (without LPG at liquid phase) at a maximum working pressure of 5 bar.

DIN EN 449-2008专用液化石油气装置用规范.无排气口的居室暖器(包括扩散催化燃烧的加热器)

This European Standard specifies the requirements, the test methods and the marking of domestic flueless spaceheaters, including diffusive catalytic combustion heaters, having a nominal heat input (Hs), not exceeding 4,2 kWburning 3rd family gases at nominal operating pressures not exceeding 50 mbar. referred to in the text as'appliances'.This European Standard is applicable to the following types of appliances:a) fixed heaters burning commercial butane and/or commercial propane;b) portable or mobile heaters burning either commercial butane, or, commercial butane and commercial propane including those that incorporate a LPG container installation compartment for a transportable refillable liquefied petroleum LPG container.There are no specific thermal efficiency requirements appropriate to these types of appliance as:c) all the heat produced by the combustion process is released into the space to be heated;d) the requirements with regard to the combustion performance, which is a safety matter, ensure the effective burning of the fuel gas.It does not cover appliances incorporating electrically operated gas control systems.Annex A gives the details of the categories of appliances marketed in various countries.Requirements for appliances given in this standard assume that the supply of gas from the container will begoverned by a pressure regulator having a maximum nominal outlet pressure of 50 mbar.This European Standard does not cover LPG containers for liquefied petroleum gas neither their associatedregulator nor tubing and flexible hoses which shall comply with national requirements in force.This European Standard only covers type testing.

DIN EN 746-2-2011工业热处理设备.第2部分:燃烧和燃料处理系统的安全要求;德文版本EN 746-2-2010

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (In this standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers:- fuel pipework downstream of and including the manual isolating valve;- burner(s), burner system and ignition device;- safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy.For thermal or catalytic post combustion and waste incineration, this European Standard applies only to auxiliary burners designed to start-up and/or support the process.The pressure hazard of piping and components covered by this standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system.Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with in this standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.