浆状油墨检测

浆状油墨检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 13217.3-2022油墨细度检验方法

本文件描述了油墨细度的检验方法。本文件适用于浆状油墨和液体油墨的产品。

GB/T 18723-2002印刷技术 用黏性仪测定浆状油墨和连接料的黏性

本标准规定了浆状油墨及其连接料黏性的通用测定方法。 本标准适用于在正常环境条件下，在测试过程中挥发性低且不发生反应的油墨的黏性测定。

GB/T 22467.2-2008防伪材料通用技术条件.第2部分:防伪油墨和印油

GB/T 22467的本部分规定了各类防伪油墨和印油的术语和定义，分类，要求，试验方法，检验规则，标志、标签、包装、运输和贮存。本部分适用于各类防伪油墨和防伪印油。本部分也适用于指导各类防伪油墨和防伪印油产品标准的编写。

GB/T 22770-2008印刷技术 用落棒式粘度计测定浆状油墨和连接料的流变性

本标准规定了在常温条件下测定不会发生反应的浆状油墨和连接料的粘度和屈服值的测定方法。本标准适用于表观粘度在2 Pa•s-200 Pa•s浆状油墨及其连接料的粘度和屈服值的测定。

GB/T 30329.1-2013印刷技术 四色印刷油墨颜色和透明度 第1部分:单张纸和热固型卷筒纸胶印

GB/T 30329的本部分规定了四色胶印用原色油墨在胶印打样和印刷过程中应满足的颜色和透明度特性,同时规定了印刷条件(使用实验室用印刷适性仪)、定义承印物和确保一致性的测试方法。本部分适用于单张纸、热固型卷筒纸和光固化胶印。本部分不适用于荧光油墨,未指定颜料(或光谱特性,提示性信息除外),从而使不同颜料优化组合也可以达到本部分规定的色度要求。

GB/T 38153.1-2019印刷技术 测试印样的实验室制备 第1部分:浆状油墨

GB/T 38153的本部分规定了用浆状油墨制备印样的实验室方法(如用于平版印刷和凸版印刷的油墨)。这种印刷样品适用于以反射为基础的测量，如色度和反射密度，以及用于耐光性的测试，同时还适用于印刷油墨和/或承印物的力学性能和耐化学性能测试。

QB/T 1865-2014胶印轮转冷固型油墨

本标准规定了胶印轮转冷固型油墨的产品分类、要求、试验方法、检验规则和标志、包装、运输、贮存。本标准适用于胶印轮转印刷机在胶版、凸版、新闻卷筒纸及非涂层纸上印刷使用的胶印轮转冷固型油墨。

QB/T 2025-2013平版印铁油墨

本标准规定了平版印铁油墨的分类、要求、试验方法、检验规则、标志、包装、运输、贮存。本标准适用于在单、双或多色印铁胶印机上使用的,在平版印刷的镀锡(铬)薄钢板包装装潢印刷品或平版印刷的铝材包装装潢印刷品上印刷的平版印铁油墨。

QB/T 2624-2012单张纸胶印油墨

本标准规定了单张纸胶印油墨(哑光型、合成纸型油墨除外)的产品分类、要求、试验方法、检验规则和标志、包装、运输、贮存。本标准适用于在单、双或多色胶印机上使用的,在纸张、薄膜等承印物上印刷图片及商标等胶印单张纸油墨。

QB/T 5192-2017广色域单张纸胶印油墨

本标准规定了广色域单张纸胶印四色油墨的术语和定义、要求、试验方法、检验规则和标志、包装、运输和贮存。本标准适用于在单、双或多色胶印机上使用的，在纸张等承印物上印刷图片及商标等广色域单张纸胶印油墨。

QB/T 5193-2017全植物油胶印油墨

本标准规定了全植物油胶印油墨的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。本标准适用于纸张印刷使用的全植物油单张胶印油墨，不包括紫外线固化胶印油墨。

QB/T 5194-2017无水胶印油墨

本标准规定了无水胶印油墨的术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输、贮存。本标准适用于普通无水胶印油墨以及紫外光固化无水胶印油墨。

ISO 2834-1-2020印刷技术. 测试印样的实验室制备. 第1部分: 浆状油墨

This document specifies a test procedure for the preparation of test prints on paper, board, metals, foils and other suitable substrates using paste inks, such as for offset and letterpress printing, using electrically driven IGT-type and prüfbau-type printability testers. This document describes the procedure for reference optical density and reference ink film thickness. This document describes the method as used on the current models of testers. Most of the described procedures are also applicable in analogy to the older models but can require additional steps to be executed or recalculation of the settings to make them conform to this document

ASTM D7680-2010用电力驱动适印性测定仪制备浆状油墨印刷品的标准操作规程

It is generally recognized that the best method for evaluating printing properties of ink-substrate combinations is by actual printing. this practice provides a convenient method for preparing repeatable laboratory prints at realistic conditions of printing speed, printing pressure and ink film thickness. This practice is useful for quality control, specification acceptance between producer and user, product development and research. Printed samples have found widespread applications for color matching, gloss-ink holdout and other appearance properties, permanency, abrasion, drying time and many other tests of interest to the printing ink, paper and allied industries.1.1 This practice describes the procedure for preparing laboratory prints of paste printing inks using a motor-driven printability tester. 1.2 This practice covers printability testers of four different designs, referred to as Tester A, B, C, and D. These testers feature x201C;push-buttonx201D; control of printing speed and pressure and facilitate measurement of exact ink film thickness. 1.3 This practice is intended primarily for lithographic and letterpress inks that dry by oxidation or penetration. With appropriate drying or curing equipment, it is also applicable to other systems such as heat-set or energy curable. 1.4 This practice is applicable to the preparation of single-color solid-area prints by dry offset (also know as letterset) or by letterpress on any flat surface including paper, paperboard, plastic film, textiles, and metal. 1.5 The values stated in SI units are to be regarded as the standard. The only other unit of measurement used is fpm. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TS ISO 12634-2003印刷技术. 用黏性仪测定浆状油墨和连接料的黏性

This standard specifies the procedure for determining the tack value of pasta inks and vehicles which have low volatility and are unreactive under normal room conditions during the span required for testing

TS ISO 12644-2002用落棒黏度计对浆状油墨和载色剂的流变特性进行图像技术测定

This standard specifies the procedure for determining the viscosity and yield valve of paste inks and vehicles which are unreaktive under normal room conditions.

ABNT NBR ISO 12634-2004印刷技术 - 浆状油墨和车辆粘性旋转粘性计测定

Specifies the procedure for determining the tack value of paste inks and vehicles which have low volatility and are unreactiv under normal conditions during the time span required for testing. Contains a description of the rotary tackmeters most commonly used.

ABNT NBR ISO 12644-1999印刷技术 - 浆状油墨和车辆的流变性能测定下降杆粘度计

Contains the procedure for determining the viscosity of paste inks and vehicles which are unreactive under normal room conditions. Applicable to inks in the apparent viscosity range of 2 Pas to 200 Pas.