建筑接缝用密封胶检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 14682-2006建筑密封材料术语

本标准规定了建筑密封材料的常用术语和定义。本标准适用于建筑密封材料领域及相关行业。

GB/T 14683-2017硅酮和改性硅酮建筑密封胶

本标准规定了硅酮和改性硅酮建筑密封胶产品的术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于普通装饰装修和建筑幕墙非结构性装配用硅酮建筑密封胶，以及建筑接缝和干缩位移接缝用改性硅酮建筑密封胶。

GB/T 22083-2008建筑密封胶分级和要求

本标准对建筑用密封胶根据其性能及应用进行分类和分级，并给出了不同级别的要求和相应试验方法。

GB/T 34327-2017建筑幕墙术语

本标准规定了建筑幕墙的通用术语和定义。本标准适用于各种类型的建筑幕墙。

GB/T 35609-2017绿色产品评价防水与密封材料

本标准规定了绿色建筑防水与密封材料的术语和定义、评价要求、评价方法。本标准适用于建筑防水卷材、防水涂料和密封胶的绿色产品评价。

GB 50108-2008地下工程防水技术规范

本规范适用于工业与民用建筑地下工程、防护工程、市政隧道、山岭及水底隧道、地下铁道、公路隧道等地下工程防水的设计和施工。

CECS 217-2006聚硫、聚氨酯密封胶给水排水工程应用技术规程

本规程适用于双组份聚硫、双组份聚氨酯建筑密封胶(以下简称聚硫、聚氨酯密封胶)防水密封工程的材料选用、施工及验收。水利、市政、地铁、隧道、道路、机场、建筑等工程中采用聚硫、聚氨酯密封胶防水密封时，可参照本规程执行。

JC/T 484-2006丙烯酸酯建筑密封胶

　　本标准规定了建筑接缝用丙烯酸酯密封胶的产品的分类、要求、试验方法、检验规则及标志、包装、运输、贮存的基本要求。　　本标准适用于以丙烯酸酯乳液为基料的单组分水乳型建筑密封胶。

JC/T 881-2017混凝土接缝用建筑密封胶

本标准规定了混凝土接缝用建筑密封胶的术语和定义、分类和标记、要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于混凝土接缝用建筑密封胶。

SH/T 3132-2013石油化工钢筋混凝土水池结构设计规范

本规范规定了石油化工钢筋混凝土水池的材料、荷载、计算及构造的要求。本规范适用于石油化工现浇钢筋混凝土水池、非贮液池及地下式、半地下式泵房的结构设计。本规范不适用于装配式钢筋混凝土水池、预应力混凝土水池及沉井类结构设计。本规范不涉及水池地基处理,当需要进行地基处理时,应符合现行有关地基处理技术规范的规定。

JG/T 372-2012建筑变形缝装置

本标准规定了建筑变形缝装置的术语和定义、分类及代号、标记、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于变形缝宽度为6mm～500mm，伸缩量为±3mm～±250mm的建筑变形缝装置。

JGJ 103-2008塑料门窗工程技术规程

本规程适用于未增塑聚氯乙烯（PVC-U）塑料门窗的设计、施工、验收及保养维修。

JGJ/T 181-2009房屋建筑与市政基础设施工程检测分类标准

本标准适用于房屋建筑和市政基础设施工程检测的分类。

JGJ/T 212-2010地下工程渗漏治理技术规程

本规程适用于地下工程渗漏的治理。

JGJ/T 400-2017装配式劲性柱混合梁框架结构技术规程

本规程适用于抗震设防烈度为6度、7度和8度地震区装配式劲性柱混合梁框架结构工程的设计、施工及验收。

TB 10003-2016铁路隧道设计规范

本规范适用于高速铁路、城际铁路、重载铁路和客货共线Ⅰ、Ⅱ级铁路标准轨距隧道设计。

ASTM C1642-2007气溶胶泡沫填缝剂和其它建筑填缝及绝缘材料漏气率的测定用标准实施规程

This practice is intended to measure air flow through materials used to fill joints found in building construction. This practice does not purport to establish all required criteria for the selection of an air barrier assembly. Therefore, the results should be used only for comparison purposes and should not be seen as the equivalent to field installed building systems.1.1 This practice is intended to determine the air leakage rate of aerosol foam sealants as measured in a standardized jig. This practice provides a procedure for preparing the test apparatus and further describes the application of aerosol foam sealant and other joint fillers to the apparatus prior to conducting Test Method E 283.1.2 This practice allows testing laboratories to quantify the air leakage rate of aerosol foam sealants or joint filling products using Test Method E 283 and reporting the data in L/(s m2) according to Practice E 29.1.3 This practice is used in conjunction with Test Method E 283. Although Test Method E 283 is a laboratory test method used with fenestration products, individuals interested in performing field air leakage tests on installed units should reference Test Method E 783 and AAMA 502.1.4 Aerosol foam sealants are used for a variety of end use applications generally intended to reduce air leakage in the building envelope.1.5 Insulating type materials also will be found suitable for evaluation with this practice. 1.6 There are no other known practices or test methods that specify the preparation of the assemblies used to determine the air leakage rate of gap filling sealants, dry preformed foams or insulations.1.7 The values given in SI units are the standard. The inch-pound units in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1642-2014气溶胶泡沫填缝剂和其它建筑填缝及绝缘材料漏气率的测定用标准实施规程

5.1x00a0;This practice is intended to measure air flow through materials used to fill joints found in building construction. 5.2x00a0;This practice does not purport to establish all required criteria for the selection of an air barrier assembly. Therefore, the results should be used only for comparison purposes and should not be seen as the equivalent to field installed building systems. 1.1x00a0;This practice is intended to determine the air leakage rate of aerosol foam sealants as measured in a standardized jig. This practice provides a procedure for preparing the test apparatus and further describes the application of aerosol foam sealant and other joint fillers to the apparatus prior to conducting Test Method E283. 1.2x00a0;This practice allows testing laboratories to quantify the air leakage rate of aerosol foam sealants or joint filling products using Test Method E283 and reporting the data in L/(s8201;x00b7;8201;m2) according to Practice E29. 1.3x00a0;This practice is used in conjunction with Test Method E283. Although Test Method E283 is a laboratory test method used with fenestration products, individuals interested in performing field air leakage tests on installed units should reference Test Method E783 and AAMA 502. 1.4x00a0;Aerosol foam sealants are used for a variety of end use applications generally intended to reduce air leakage in the building envelope. 1.5x00a0;Insulating type materials also will be found suitable for evaluation with this practice. 1.6x00a0;There are no other known practices or test methods that specify the preparation of the assemblies used to determine the air leakage rate of gap filling sealants, dry preformed foams or insulations. 1.7x00a0;The values given in SI units are the standard. The inch-pound units in parentheses are for information only. 1.8x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.