成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

扩张式封隔器检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 8423.5-2017石油天然气工业术语 第5部分:设备与材料

GB/T 8423的本部分界定了石油天然气工业用钻井设备、采油设备、海洋专用设备、钻采工具、石油管材和石油仪器等领域的术语。本部分适用于石油天然气勘探开发工程、钻井工程、采油工程、石油管工程和石油仪器仪表等应用领域。

GB/T 21412.1-2010石油天然气工业 水下生产系统的设计与操作 第1部分:一般要求和推荐做法

本部分制定了整套水下生产系统从设计到废弃各个阶段的一般要求和推荐做法,作为一个纲领性文件用于指导和制定涉及到水下生产系统各个组成部分更为详细要求的子系统标准。同时,对于子系统标准内未包括的某些部分,如系统设计、结构、管汇、吊装设备、颜色和标记等,也给出了较为详细的要求。对那些应用范围有限的特种设备,如密闭在干式舱中的组合式采油树、采油树和管汇等,这里未做专门讨论,但本部分中的相关条款同样适用于这类设备。

GB/T 24956-2010石油天然气工业 钻柱设计和操作限度的推荐作法

本标准不仅包括钻柱组件的选择,而且还考虑了井斜控制、钻井液、钻压和转速,以及其他操作程序。

HG/T 2702-2016扩张式封隔器胶筒

本标准规定了油田、煤气田、页岩气田用扩张式封隔器胶筒的术语和定义,结构、代号,要求,检验规则以及标志、包装、运输和贮存。本标准适用于油田分层测试、注水、酸化和压裂,煤层气测试压裂,页岩气测试压裂等用扩张式封隔器胶筒及完井用扩张式封隔器胶筒(以下均简称胶筒)。

SL 373-2007水利水电工程水文地质勘察规范

本标准适用于大型水利水电工程的水文地质勘察工作,中、小型水利水电工程可参照执行。

SY/T 5745-2008采油采气工程词汇

本标准规定了采油采气工程常用词汇。本标准适用于石油天然气工业采油采气工程领域,也适用于石油工业其他领域。

SY/T 5924-2011油井堵水作业方法.裸眼井机械卡堵水作业

本标准规定了裸眼井机械卡堵水作业的管柱结构类型、井下配套工具的参数、施工准备、施工程序、质量控制和健康、安全、环境控制要求。 本标准适用于井径150mm~180mm垂向裸眼井机械方法卡堵水作业,仅适用扩张式钢带封隔器(以下简称封隔器)。

SY/T 6756-2009油气藏改建地下储气库注釆井修井作业规范

本标准规定了由油气藏改建的地下储气库注釆井修井作业的设计、施工特殊材料和设备准备、施工工序、井控、HSE、质量控制等要求。本标准适用于由油气藏改建的地下储气库注釆井修井作业。

EN ISO 13628-1-2005石油和天然气工业.水下采油系统的设计和操作.第1部分:一般要求和建议 ISO 13628-1-2005

This part of ISO 13628 provides general requirements and overall recommendations for development of complete subsea production systems, from the design phase to decommissioning and abandonment.This part of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with more detailed requirements for the subsystems which typically form part of a subsea production system. However, in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) more detailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbons from one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floating or subsea) or onshore, or to inject water/gas through subsea wells.This part of ISO 13628 and its related subsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are not specifically discussed because of their limited use. However, the information presented is applicable to those types of equipment.If requirements as stated inThis part of ISO 13628 are in conflict with, or are inconsistent with, requirements as stated in the relevant complementary parts of ISO 13628, then the specific requirements in the complementary parts take precedence.

DIN EN 1537-2014特殊土工作业.地锚

This Standard applies to the installation and monitoring of permanent and temporary ground anchors. It covers anchors which are able to be stressed and are able to be tested in accordance with EN ISO 22477-5. The planning and design of ground anchors calls for experience and knowledge in this specialised field and although these topics are covered briefly in EN 1997-1 Eurocode 7 : Geotechnical Design, Part 1 : General Rules. This Standard does not address alternative systems of anchoring such as tension piles, screw anchors, mechanical anchors, soil nails, expander anchors or deadman anchors.

DIN EN ISO 772-2011液体比重测定法.词汇和符号(ISO 772-2011):三种语言版本EN ISO 772-2011

This International Standard gives terms, definitions and symbols used in standards in the field of hydrometry.

DIN EN ISO 17348-2016石油和天然气工业.套管,油管和井下设备较高二氧化碳含量的环境下材料选择(ISO 17348-2016).英文版本EN ISO 17348-2016

This International Standard provides guidelines and requirements for material selection of both seamless casing and tubing, and downhole equipment for CO2 gas injection and gas production wells with high pressure and high CO2 content environments [higher than 10 % (molar) of CO2 and 1 MPa CO2 partial pressure]. Oil production wells are not covered in this International Standard. This International Standard only considers materials compatibility with the environment. Guidance is given for the following: - corrosion evaluation; - materials selection; - corrosion control. This International Standard is aimed at high CO2 content wells, where the threat of low pH and CO2 corrosion is greatest. However, many aspects are equally applicable to environments containing lower CO2 concentrations. Materials selection is influenced by many factors and synergies and should be performed by either materials or corrosion engineer.

DIN EN ISO 23936-2-2012石油,石化和天然气工业.油气生产与介质有联系的非金属材料.第2部分:人造橡胶(ISO 23936-2-2011).英文版本 EN 23936-2-2011

ISO 23936 describes general principles and gives requirements and recommendations for the selection and qualification of non-metallic materials for service in equipment used in oil and gas production environments, where the failure of such equipment could pose a risk to the health and safety of the public and personnel, or to the environment. It can be applied to help avoid failures of the equipment itself. It supplements, but does not replace, the material requirements given in the appropriate design codes, standards or regulations. This part of ISO 23936 describes the requirements and procedures for qualification of elastomeric material used in equipment for oil and gas production.

BS EN ISO 13628-1-2005+A1-2010石油和天然气工业.水下采油系统的设计和操作.第1部分:一般要求和推荐规范

This part of ISO 13628 provides general requirements and overall recommendations for development ofcomplete subsea production systems, from the design phase to decommissioning and abandonment. Thispart of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with moredetailed requirements for the subsystems which typically form part of a subsea production system. However,in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) moredetailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbonsfrom one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floatingor subsea) or onshore, or to inject water/gas through subsea wells. This part of ISO 13628 and its relatedsubsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are notspecifically discussed because of their limited use. However, the information presented is applicable to thosetypes of equipment.If requirements as stated in this part of ISO 13628 are in conflict with, or are inconsistent with, requirementsas stated in the relevant complementary parts of ISO 13628, then the specific requirements in thecomplementary parts take precedence.

上一篇电梯及部件检测 下一篇丢手可钻封隔器、桥塞及坐封工具检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通