丝绒毛巾检测

丝绒毛巾检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 17780.6-2012纺织机械.安全要求.第6部分：织造机械

GB/T 17780的本部分规定了织造机械的主要危险及相关安全要求和/或措施。本部分适用于织造、针织和簇绒使用的所有机器、设备和相关装置。本部分与GB/T 17780.1结合使用。

EN 14697-2005纺织品.丝绒毛巾和丝绒毛巾织物.规范和试验方法

This document specifies minimum requirements for properties and test methods forThe evaluation of new readymade terry towels and to new terry fabrics, for contract and domestic use.This document covers woven terry structures only.This document does not cover towels used inThe health care sector (see ENV 14237) or cabinet roller towels (see EN 13569).

NF G33-005-2005纺织品.丝绒毛巾和丝绒织物.规范和试验方法

Le présent document spécifie les exigences minimales pour les propriétés et les méthodes d'essai relatives à l'évaluation des serviettes éponges neuves et des tissus éponges neufs, destinés à des usages domestiques et professionnels.Le présent document couvre uniquement les structures tissées en éponge.Le présent document ne couvre pas les serviettes utilisées dans le domaine de la santé (voir l'ENV 14237) ou les serviettes essuie-mains textiles en bobine (voir l'EN 13569).

DIN EN 14697-2005纺织品.丝绒毛巾和丝绒毛巾织物.规范和试验方法

This document specifies minimum requirements for properties and test methods for the evaluation of new ready-made terry towels and to new terry fabrics, for contract and domestic use. This document covers woven terry structures only. This document does not cover towels used in the health care sector (see ENV 14237) or cabinet roller towels (see EN 13569).#,,#

DIN EN ISO 10414-2-2011石油和天然气工业.钻井液的现场测试.第2部分:油基液(ISO 10414-2-2011);英文版本EN ISO 10414-2-2011,仅限CD-ROM

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-based drilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluid balances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).

BS EN 14697-2005纺织品.丝绒毛巾和丝绒毛巾织物.规范和试验方法

This document specifies minimum requirements for properties and test methods for the evaluation of new ready-made terry towels and to new terry fabrics, for contract and domestic use.\nThis document covers woven terry structures only.\nThis document does not cover towels used in the health care sector (see ENV 14237) or cabinet roller towels (see EN 13569).

BS EN ISO 10414-2-2011石油和天然气工业.钻井液的现场测试.油基液

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-baseddrilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluidbalances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).