成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

铅和铅合金检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 32346.1-2015额定电压220 kV(Um=252 kV)交联聚乙烯绝缘大长度交流海底电缆及附件 第1部分:试验方法和要求

GB/T 32346的本部分规定了额定电压220 kV(U<下标m> = 252 kV)交联聚乙烯绝缘大长度交流海底电缆及其附件的试验方法和要求。本部分适用于安装在海底的220 kV单芯和三芯交联聚乙烯绝缘海底电缆和光纤复合交联聚乙烯绝缘海底电缆;也适用于工厂接头(软接头)、修理接头、海底电缆与陆上电缆间过渡接头和终端等海底电缆附件。本部分不适用于特殊应用场合如海上浮动平台的动态电缆的试验。这种动态电缆受到另一种机械应力,因此不包括在本部分适用范围以内。

JB/T 11167.1-2011额定电压10kV(U<下标m>=12kV)至110kV(U<下标m>=126kV)交联聚乙烯绝缘大长度交流海底电缆及附件.第1部分:试验方法和要求

JB/T 11167的本部分规定了额定电压10kV(U<下标m>=12kV)至110kV(U<下标m>=126kV)交联聚乙烯绝缘大长度交流(以下海底电缆均指交流海底电缆)海底电缆及其附件的试验方法和要求。此试验方法和要求适用于10kV至110kV单芯和三芯交联聚乙烯绝缘海底电缆和光纤复合交联聚乙烯绝缘海底电缆;也适用于包含工厂接头(软接头)、修理接头和终端的附件。

AS 2611-1983铅和铅合金光学发射谱法固体样品的采样和制备

This standard sets out methods for the sampling of lead and lead alloys and procedures for the preparation of the test samples required for the determination of composition by optical emission spectrometry. Samples may be taken from cast forms or from the molten metal.NOTE: Extreme care must be taken to ensure that any remelting is carried out under the conditions specified in Clause 6.

AS_NZS 2893-2002电缆铅和铅合金护套组成

This Standard specifies the chemical composition of cable metallic sheathing made from lead and three lead alloys.

ASTM B29-2003精炼铅标准规范

1.1 This specification covers refined lead in pig, block, or hog form.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

ASTM B319-1991(1997)电镀用铅和铅合金的制备标准指南

1.1 This guide provides methods for preparing lead or lead alloy products for the application of electroplated or autocatalytic coatings. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B319-1991(2004)电镀用铅和铅合金的制备

The preparation of lead and lead-alloy surfaces for electroplating is often critical to the successful performance of electrodeposited and autocatalytic metallic coatings. This standard outlines the process operation procedures and processing solutions required, that lead to satisfactory electrodeposited metallic coatings (including undercoating) on surfaces of lead and lead-alloys.1.1 This guide provides methods for preparing lead or lead alloy products for the application of electroplated or autocatalytic coatings.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B319-1991(2009)电镀用铅和铅合金的制备的标准指南

The preparation of lead and lead-alloy surfaces for electroplating is often critical to the successful performance of electrodeposited and autocatalytic metallic coatings. This standard outlines the process operation procedures and processing solutions required, that lead to satisfactory electrodeposited metallic coatings (including undercoating) on surfaces of lead and lead-alloys.1.1 This guide provides methods for preparing lead or lead alloy products for the application of electroplated or autocatalytic coatings. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B319-1991(2014)电镀用铅和铅合金制备的标准指南

3.1x00a0;The preparation of lead and lead-alloy surfaces for electroplating is often critical to the successful performance of electrodeposited and autocatalytic metallic coatings. 3.2x00a0;This standard outlines the process operation procedures and processing solutions required, that lead to satisfactory electrodeposited metallic coatings (including undercoating) on surfaces of lead and lead-alloys. 1.1x00a0;This guide provides methods for preparing lead or lead alloy products for the application of electroplated or autocatalytic coatings. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B319-1991(2020)电镀用铅和铅合金制备的标准指南

1.1?This guide provides methods for preparing lead or lead alloy products for the application of electroplated or autocatalytic coatings. 1.2?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM B749-1997铅和铅合金带材、薄板和板材产品标准规范

1.1 This specification covers lead sheet, strip, and plate of various alloys intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding. 1.2 The values stated in inch-pound units are to be regarded as the standard.

ASTM B749-2003铅和铅合金带材、薄板和板材产品标准规范

1.1 This specification covers lead sheet, strip, and plate of various alloys intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding.1.2 The values stated in inch-pound units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

ASTM B749-2003(2009)铅和铅合金带材、薄板材和板材产品的标准规范

1.1 This specification covers lead sheet, strip, and plate of various alloys intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

ASTM B749-2014铅和铅合金带材, 薄板材和厚板材产品的标准规格

1.1x00a0;This specification covers lead sheet, strip, and plate of various alloys intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

ASTM B749-2020铅和铅合金带材、薄板和板材产品的标准规范

1.1 This specification covers lead sheet, strip, and plate of various alloys intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM B982-2012光发射光谱测定或电感耦合等离子体(ICP)分析铅和铅合金的抽样和样品制备标准规范

1.1 This specification covers the sampling of lead and lead alloys to obtain a sample suitable for quantitative optical emission spectrochemical analysis. Included are procedures for sample preparation, obtaining representative samples from molten metal, from fabricated, or cast products that can be melted, and from other forms that cannot be melted. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B982-2014光发射光谱测定或电感耦合等离子体 (ICP) 分析用铅和铅合金的取样和样品制备标准规范

1.1x00a0;This specification covers the sampling of lead and lead alloys to obtain a sample suitable for quantitative optical emission spectrochemical analysis. Included are procedures for sample preparation, obtaining representative samples from molten metal, from fabricated, or cast products that can be melted, and from other forms that cannot be melted. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B982-2014e1光发射光谱测定或电感耦合等离子体 (ICP) 分析用铅和铅合金的取样和样品制备标准规范

1.1x00a0;This specification covers the sampling of lead and lead alloys to obtain a sample suitable for quantitative optical emission spectrochemical analysis. Included are procedures for sample preparation, obtaining representative samples from molten metal, from fabricated, or cast products that can be melted, and from other forms that cannot be melted. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B982-2020光发射光谱或ICP分析用铅和铅合金的取样和样品制备的标准规范

1.1 This specification covers the sampling of lead and lead alloys to obtain a sample suitable for quantitative optical emission spectrochemical analysis. Included are procedures for sample preparation, obtaining representative samples from molten metal, from fabricated, or cast products that can be melted, and from other forms that cannot be melted. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

上一篇医用 X、γ射线机房检测 下一篇疾病控制类样本检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通