压力容器钢板检测
GB/T 8650-2015管线钢和压力容器钢抗氢致开裂评定方法
本标准规定了管线钢和压力容器钢板以及法兰和管件在含有硫化物水溶液的腐蚀环境中,由于腐蚀吸氢引起的氢致开裂(HIC)的评定方法。本标准提供了从每个钢产品类型中取样的尺寸,数量,位置和取向,钢产品的类型包括钢管、钢板、管件和法兰。本标准包括小直径(公称直径[DN]50~150,公称管线尺寸[NPS]为2~6)、薄壁(壁厚不大于6 mm)电阻焊(ERW)和无缝钢管的特殊步骤要求。除非本标准中特殊规定,这些小直径、薄壁材料宜与其他钢管用相同的方法进行试验。本标准不包含接受或者否决的准则,但GB/T 20972.2-2008的第8章提供了指南。
SY/T 6620-2014油罐的检验、修理、改建及翻建
本标准适用于依照API Std 650及其前身API Std 12C而建造的钢制储罐,提出了在安装使用后保持其完整性的低要求,并讨论它们的检验、修理、改建、移位和翻建。本标准范围限于油罐基础、罐底、罐壁、构架、罐顶、附件和接管,直至第一个法兰面、第一个螺纹接头或第一个焊接接口。API Std 650的许多设计、焊接、检验和材料的要求可以用于油罐的维修检验、标定、修理和改建上。当本标准与API Std 650或其前版API Std 12C要求有明显抵触时,以本标准为准。本标准采用API Std 650的原则,储油罐业主/操作者出于特殊建造和操作细节的考虑,可以将本标准用于依储罐规范建制的任何钢罐。本标准可用于维修,也可用于工程和检验人员在油罐设计、制造、修理、建造与检验方面的技术培训和经验交流。本标准未囊括现有油罐可能出现的所有不同条件下的规程或准则。如设计和建造细节未知,且不能在现有标准中找到,则使用与API Std 650新版本规定的同等完整性水平的详细资料。本标准承认评估在役压力控制构件退化的工况适应性评价概念。API RP 579为本标准中涉及的不同类型的退化提供了详细的评估过程和合格的标准。当本标准不能为具体的退化类型提供具体的评估过程和合格的标准或者本标准明确允许使用运行适宜性原则,则API RP 579可用来评估在本标准中不同的老化类型和测试要求。
SN/T 1733.11-2006非正品钢材检验鉴定规程.第11部分:热轧钢板和钢带
本部分规定了非正品热轧钢板和钢带的定义、技术要求、检验鉴定规则和检验结果的判定。 本部分适用于非正品热轧钢板和钢带及一级剩余品等热轧和钢带的检验鉴定。不适用于非正品热轧压力容器钢板、汽车用钢板、集装箱用钢板等专用钢板。
ASTM A20/A20M-2006压力容器用钢板一般要求的标准规范
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM:1.1.1 This general requirements specification also covers a group of supplementary requirements that are applicable to several of the above product specifications as indicated therein. Such requirements are provided for use if additional testing or additional restrictions are required by the purchaser, and apply only if specified individually in the purchase order. 1.2 Appendix X1 provides information on coil as a source of plates for pressure vessels. 1.3 Appendix X2 provides information on the variability of tensile properties in plates for pressure vessels.1.4 Appendix X3 provides information on the variability of Charpy-V-Notch impact test properties in plates for pressure vessels. 1.5 Appendix X4 provides information on cold bending of plates, including suggested minimum inside radii for cold bending.1.6 These materials are intended to be suitable for fusion welding. When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. 1.7 In case of any conflict in requirements, the requirements of the applicable product specification prevail over those of this general requirements specification. 1.8 Additional requirements that are specified in the purchase order and accepted by the supplier are permitted, provided that such requirements do not negate any of the requirements of this general requirements specification or the applicable product specification.1.9 For purposes of determining conformance with this general requirements specification and the applicable product specification, values are to be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.10 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system is to be used independently of the other. 1.11 This general requirements specification and the applicable product specification are expressed in both inch-pound units and SI units; unless the order specifies the applicable \"M\" specification designation (SI units), the plates are to be furnished to inch-pound units.
ASTM A20/A20M-2007压力容器用钢板通用要求标准规范
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM:1.1.1 This general requirements specification also covers a group of supplementary requirements that are applicable to several of the above product specifications as indicated therein. Such requirements are provided for use if additional testing or additional restrictions are required by the purchaser, and apply only if specified individually in the purchase order. 1.2 Appendix X1 provides information on coil as a source of plates for pressure vessels. 1.3 Appendix X2 provides information on the variability of tensile properties in plates for pressure vessels.1.4 Appendix X3 provides information on the variability of Charpy-V-Notch impact test properties in plates for pressure vessels. 1.5 Appendix X4 provides information on cold bending of plates, including suggested minimum inside radii for cold bending.1.6 These materials are intended to be suitable for fusion welding. When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. 1.7 In case of any conflict in requirements, the requirements of the applicable product specification prevail over those of this general requirements specification. 1.8 Additional requirements that are specified in the purchase order and accepted by the supplier are permitted, provided that such requirements do not negate any of the requirements of this general requirements specification or the applicable product specification.1.9 For purposes of determining conformance with this general requirements specification and the applicable product specification, values are to be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29. 1.10 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.11 This general requirements specification and the applicable product specification are expressed in both inch-pound units and SI units; unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the plates are to be furnished to inch-pound units.
ASTM A20/A20M-2009压力容器用钢板通用要求标准规范
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM:
ASTM A20/A20M-2010压力容器用钢板通用要求标准规格
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM:
ASTM A20/A20M-2011压力容器钢板一般要求的标准规格
1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM: Title of SpecificationASTM DesignationA Pressure Vessel Plates, Alloy Steel, Nickel A203/A203M Pressure Vessel Plates, Alloy Steel, MolybdenumA204/A204M Pressure Vessel Plates, Alloy Steel, Manganese- Vanadium A225/A225M Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile StrengthA285/A285M Pressure Vessel Plates, Carbon Steel, Manganese-Silicon A299/A299M Pressure Vessel Plates, Alloy Steel, Manganese- Molybdenum and Manganese-Molybdenum-NickelA302/A302M Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel Double-Normalized and TemperedA353/A353M Pressure Vessel Plates, Alloy Steel, Chromium- Molybdenum A387/A387M Pressure Vessel Plates, Carbon Steel, High Strength ManganeseA455/A455M Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service A515/A515M Pressure Vessel Plates, Carbon Steel, Moderate- and Lower-Temperature ServiceA516/A516M Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and TemperedA517/A517M Pressure Vessel Plates, Alloy Steel, Quenched and Tempered Manganese-Molybdenum and Manganese- Molybdenum- NickelA533/A533M Pr
ASTM A20/A20M-2013压力容器钢板一般要求的标准规格
1.1x00a0;This general requirements specification2 covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM: Title of Specification ASTM DesignationA Pressure Vessel Plates, Alloy Steel, Nickel A203/A203M Pressure Vessel Plates, Alloy Steel, Molybdenum A204/A204M Pressure Vessel Plates, Alloy Steel, Manganese- 8199;Vanadium A225/A225M Pressure Vessel Plates, Carbon Steel, Low- and 8199;Intermediate-Tensile Strength A285/A285M Pressure Vessel Plates, Carbon Steel, Manganese-Silicon A299/A299M Pressure Vessel Plates, Alloy Steel, Manganese- 8199;Molybdenum and Manganese-Molybdenum-Nickel A302/A302M Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel 8199;Double-Normalized and Tempered A353/A353M Pressure Vessel Plates, Alloy Steel, Chromium- 8199;Molybdenum A387/A387M Pressure Vessel Plates, Carbon Steel, High Strength 8199;Manganese A455/A455M Pressure Vessel Plates, Carbon Steel, for Intermediate- 8199;and Higher-Temperature Service A515/A515M Pressure Vessel Plates, Carbon Steel, Moderate- and 8199;Lower-Temperature Service A516/A516M Pressure Vessel Plates, Alloy Steel, High-Strength, 8199;Quenched and Tempered
ASTM A20/A20M-2014压力容器用钢板材通用要求的标准规格
1.1x00a0;This general requirements specification2 covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM: Title of Specification ASTM DesignationA Pressure Vessel Plates, Alloy Steel, Nickel A203/A203M Pressure Vessel Plates, Alloy Steel, Molybdenum A204/A204M Pressure Vessel Plates, Alloy Steel, Manganese- 8199;Vanadium A225/A225M Pressure Vessel Plates, Carbon Steel, Low- and 8199;Intermediate-Tensile Strength A285/A285M Pressure Vessel Plates, Carbon Steel, Manganese-Silicon A299/A299M Pressure Vessel Plates, Alloy Steel, Manganese- 8199;Molybdenum and Manganese-Molybdenum-Nickel A302/A302M Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel 8199;Double-Normalized and Tempered A353/A353M Pressure Vessel Plates, Alloy Steel, Chromium- 8199;Molybdenum A387/A387M Pressure Vessel Plates, Carbon Steel, High Strength 8199;Manganese A455/A455M
ASTM A20/A20M-2015压力容器用钢板材通用要求的标准规格
1.1x00a0;This general requirements specification2 covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM: Title of Specification ASTM DesignationA Pressure Vessel Plates, Alloy Steel, Nickel A203/A203M Pressure Vessel Plates, Alloy Steel, Molybdenum A204/A204M Pressure Vessel Plates, Alloy Steel, Manganese- 8199;Vanadium A225/A225M Stainless Chromium Steel-Clad Plate A263 Stainless Chromium-Nickel Steel-Clad Plate A264 Nickel and Nickel-Base Alloy Steel-Clad Plate A265 Pressure Vessel Plates, Carbon Steel, Low- and 8199;Intermediate-Tensile Strength A285/A285M Pressure Vessel Plates, Carbon Steel, Manganese-Silicon A299/A299M Pressure Vessel Plates, Alloy Steel, Manganese- 8199;Molybdenum and Manganese-Molybdenum-Nickel A302/A302M Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel 8199;Double
ASTM A203/A203M-2012压力容器用镍合金钢板的标准规格
1.1 This specification covers nickel-alloy steel plates intended primarily for welded pressure vessels. 1.2 Plates under this specification are available with four strength levels and two nickel compositions as follows: GradeNominal Nickel Content %Yield Strength, min, ksi [MPa]Tensile Strength, min, ksi [MPa] A2.2537 [255]65 [450] B2.2540 [275]70 [485] D3.5037 [255]65 [450] E3.5040 [275]70 [485] F3.50 2 in. [50 mm] and under 55 [380] 80 [550] cccc Over 2 in. [50 mm] 50 [345] 75 [515] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements. However, current practice normally limits the maximum thickness of plates furnished under this specification as follows: Grade Maximum Thickness, in. [mm] A6 [150] B6 [150] D4 [100] E4 [100] F4 [100] 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
ASTM A204/A204M-2003压力容器用钼合金钢板标准规范
1.1 This specification covers molybdenum-alloy steel plates, intended particularly for welded boilers and other pressure vessels. 1.2 Plates under this specification are available in three grades having different strength levels as follows: Grade Tensile Strength,ksi [MPa]A 65-85 [450-585]B 70-90 [485-620]C 75-95 [515-655] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification as follows: Grade Maximum Thickness,in. [mm]A 6 [150]B 6 [150]C 4 [100] 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
ASTM A204/A204M-2003(2007)压力容器用钼合金钢板的标准规范
1.1 This specification covers molybdenum-alloy steel plates, intended particularly for welded boilers and other pressure vessels. 1.2 Plates under this specification are available in three grades having different strength levels as follows: Grade Tensile Strength, ksi [MPa] A 65x2013;85 [450x2013;585] B 70x2013;90 [485x2013;620] C 75x2013;95 [515x2013;655] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification as follows: Grade Maximum Thickness, in. [mm] A 6 [150] B 6 [150] C 4 [100] 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
ASTM A204/A204M-2012压力容器用钼合金钢板的标准规格
1.1 This specification covers molybdenum-alloy steel plates, intended particularly for welded boilers and other pressure vessels. 1.2 Plates under this specification are available in three grades having different strength levels as follows: Grade Tensile Strength, ksi [MPa] A 65x2013;85 [450x2013;585] B 70x2013;90 [485x2013;620] C 75x2013;95 [515x2013;655] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification as follows: Grade Maximum Thickness, in. [mm] A 6 [150] B 6 [150] C 4 [100] 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
ASTM A225/A225M-2003压力容器板,合金钢,锰钒镍标准规范
1.1 This specification covers manganese-vanadium-nickel alloy steel plates intended primarily for welded layered pressure vessels. 1.2 Plates under this specification are available in two grades having different strength levels as follows:Grade Tensile Strength,ksi [MPa]CD105-135 [725-930] 3 in. [75 mm] and under Over 3 in. [75 mm]80-105 [550-725]75-100 [515-690] 1.3 The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements; however, current mill practice normally limits Grade C to 0.58 in. [15 mm] maximum and Grade D to 6 in. [150 mm] maximum. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
ASTM A225/A225M-2003(2007)压力容器用锰矾镍合金钢板的标准规范
1.1 This specification covers manganese-vanadium-nickel alloy steel plates intended primarily for welded layered pressure vessels. 1.2 Plates under this specification are available in two grades having different strength levels as follows: Grade Tensile Strength, ksi [MPa] C105x2013;135 [725x2013;930] D 3 in. [75 mm] and under 80x2013;105 [550x2013;725] Over 3 in. [75 mm]75x2013;100 [515x2013;690] 1.3 The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements; however, current mill practice normally limits Grade C to 0.58 in. [15 mm] maximum and Grade D to 6 in. [150 mm] maximum. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
ASTM A225/A225M-2012压力容器用锰矾镍合金钢板的标准规格
1.1 This specification covers manganese-vanadium-nickel alloy steel plates intended primarily for welded layered pressure vessels. 1.2 Plates under this specification are available in two grades having different strength levels as follows: Grade Tensile Strength, ksi [MPa] C105x2013;135 [725x2013;930] D 3 in. [75 mm] and under 80x2013;105 [550x2013;725] Over 3 in. [75 mm]75x2013;100 [515x2013;690] 1.3 The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements; however, current mill practice normally limits Grade C to 0.58 in. [15 mm] maximum and Grade D to 6 in. [150 mm] maximum. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
ASTM A263-2003包铬的不锈钢板标准规范
1.1 This specification covers plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of stainless chromium steel. The material is generally intended for pressure vessel use.1.2 The values stated in inch-pound units are to be regarded as the standard.
相关阅读
了解更多检测知识
道桥材料检测
道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。
洗衣凝珠检测
洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。
绿色食品检测
绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。
吐鲁番葡萄检测
吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。
食品过敏原检测
食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。
二硫化钼检测
二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。
我们的优势
选择中析研究所的八大理由
资质齐全
旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。
设备先进
上千台精密仪器定期检定校准,量值溯源体系完善。
专家团队
多领域技术专家,十年以上经验,破解各类疑难检测。
标准覆盖广
覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。
周期短
常规项目7-10个工作日出报告,流程标准高效。
加急服务
支持加急检测通道,助力客户快速完成质量把关。
一对一服务
工程师全程对接,需求沟通到报告解读全流程陪伴。
数据保密
严格保密制度,客户样品与检测数据安全无忧。
旗下实验室资质
我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。
CMA检验检测机构资质认定证书
CNAS实验室认可证书
ISO管理体系认证证书
高新技术企业证书
中国分析测试协会会员单位
中国质量协会会员证书
AAA级信用企业
绿色低碳诚信示范创建企业
仪器设备
1000余台精密设备 · 点击查看原图
气相色谱-质谱联用仪 GC-MS
复杂有机组分的定性鉴定与未知物剖析利器。
高效液相色谱仪 HPLC
食品添加剂、药品成分等热敏物质的精准检测。
电感耦合等离子体发射光谱仪 ICP-OES
一次进样同时读出数十种金属元素含量。
傅里叶变换红外光谱仪 FTIR
通过特征吸收峰快速判断材料种类与分子结构。
X射线荧光光谱仪 XRF
几分钟完成元素快检,且不损伤样品。
扫描电子显微镜 SEM
放大数十万倍观察表面微观结构,锁定失效根源。
液相色谱-质谱联用仪 LC-MS
农兽药残留等痕量物质的高灵敏确证检测。
气相色谱仪 GC
溶剂残留、香气成分等挥发性物质的专业检测。
在线工程师 一对一服务
检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。
NEW · 全新上线
VR实验室上线啦!
720°全景实景观览 · 足不出户走进实验室
立即体验
检测咨询 · 立即在线沟通