燃气用手动球阀和底部密封旋塞阀检测

燃气用手动球阀和底部密封旋塞阀检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 16662-2008建筑给水排水设备器材术语

本标准规定了建筑给水排水设备和器材，包括卫生器具，水嘴，加压、调节和贮存设备，加热贮热设备，地漏，检查井，建筑水处理设备，游泳池、游乐池设备，冷却设备，水景设备，雨水利用设备，管材，管件，阀门，计量、检测仪表等方面的专用术语。本标准适用于建筑给水排水设备和器材的专用术语。

GB 50350-2015油田油气集输设计规范

本规范适用于陆上油田、滩海陆采油田和海上油田陆岸终端油气集输工程设计。

GB 50880-2013冶炼烟气制酸工艺设计规范

本规范适用于新建、改建和扩建的冶炼烟气制酸工程项目的工艺设计。

TSG D7002-2006压力管道元件型式试验细则

本规则规定的压力管道元件型式试验是验证产品安全性能是否满足安全技术要求而进行的技术文件审查、样品检验测试和安全性能试验。

CJ/T 180-2014建筑用手动燃气阀门

本标准规定了建筑用手动燃气阀门(以下简称阀门)的分类及型号,材料、结构和连接尺寸,要求,试验方法,检验规则,标志、包装、运输和贮存。本标准适用于公称压力不大于1.6 MPa、公称尺寸不大于100 mm、工作温度不超出-20 ℃~60 ℃且其下限不低于燃气露点温度,安装在建筑物内外的非直埋燃气装置与设施上的手动燃气球阀和底部密封的旋塞阀。本标准所指燃气为符合GB/T 13611规定的燃气。

HJ 2000-2010大气污染治理工程技术导则

本标准规定了大气污染治理工程在设计、施工、验收和运行维护中的通用技术要求。本标准为环境工程技术规范体系中的通用技术规范。对于已有相应的工艺技术规范或污染源技术规范的工程,应同时执行本标准和相应的工艺技术规范或污染源技术规范,对于没有工艺技术规范或污染源技术规范的工程,应执行本标准。本标准可作为大气污染治理工程环境影响评价、设计、施工、验收及运行与管理的技术依据。

JB/T 4365-1997专用的润滑、轴密封和控制油系统

　　本档准规定了专用的润滑油系统、轴密封油系统及控制油系统的低要求。这些系统适用于压缩机、齿轮传动装置、泵及驱动机等设备，不适用于内燃机。 特殊声明： a）当买方在订货单或与其有关的数据表中同意系统按JB/T 4365标准供货时，就要优先采用本标准，不得优先采用其他标准中类同内容的任何条款。 b）如本标准与询价书或订货单有抵触时，则要以订货单中的资料为准。 c）附录A给出了典型系统组件的略图及典完整的润滑油系统、轴密封油系统及控制油系统图的示意图，这些略图示出了本标准的通常原理和要求，包括帮助买方选择合理的系统。在订单生效前同买方与卖方协商确定双方均能接受的系统。 d)本标准规定了买方要确定的供货范围、质量水平或部件的牌号（材质）要求。系统型式、总布置图（包括油站方位平面图和主视图）、油站占用空间及其他要求。 e)本标准规定了“设计”一词，在买方技术文件中应避免使用（如设计功率、设计压力、设计温度或设计转速）。此词条只限于设备设计人员和制造厂使用。 f）本标准规定了相应的公制尺寸、卖方可以提出变更设计（7.1报价要求）。经买卖双方协商同意，可以提供“等值的”英制的尺寸、紧固件及法兰。

DB11/T 301-2005燃气室内工程设计施工验收技术规定

本规定适用于北京市居民生活、商业及工业企业生产、采暖通风和空调使用的天然气、气态液化\r石油气、人工煤气作燃料的新建、扩建、改建燃气室内工程的设计、施工及验收

DB11/T 302-2005燃气输配工程设计施工验收技术规定

本规定适用于北京市居民生活、商业、工业企业、采暖通风和空调等用燃气作燃料的新建、扩建\r或改建的燃气输配工程的设计、施工及验收

UL 1776-2002高压清洗机

These requirements cover inverters ,converters ,charge controllers ,and output controllers intended for use in stand-alone(not grid connected) or utility-interactive (grid-connected) power systems .Utility-interactive inverters and converters are intended to be installed in parallel with an electric supply system or an electric utility to supply common loads.

DIN EN 331-2016建筑物燃气设备上的手动球阀和底部关闭锥形塞阀.德文版本EN 331-2015

This European standard specifies the characteristics for the construction, performance and safety of ball valves and closed bottom taper plug valves. It also details the test methods and marking provisions. It applies to metallic valves not directly buried for domestic and commercial installations inside or outside of buildings with pressures up to 5 bar, using gases of the first, second and third family (specified in EN 437).

DIN EN 746-2-2011工业热处理设备.第2部分:燃烧和燃料处理系统的安全要求;德文版本EN 746-2-2010

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (In this standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers:- fuel pipework downstream of and including the manual isolating valve;- burner(s), burner system and ignition device;- safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy.For thermal or catalytic post combustion and waste incineration, this European Standard applies only to auxiliary burners designed to start-up and/or support the process.The pressure hazard of piping and components covered by this standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system.Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with in this standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.

DIN EN 1775-2007供气.建筑物用煤气管道工程.大工作压力≤5bar.功能推荐

1.1 This standard specifies general recommendations for the design, construction, testing, commissioning,operation and maintenance of installation pipework; pipework between the delivery point of the gas and the inletconnection to the gas appliance.This standard specifies common basic principles for gas installation pipework.Users of this European standard need to be aware that more detailed national standards and/or codes of practicemay exist in the CEN member countries.This standard is intended to be applied in association with these national standards and/or codes of practice settingout the above mentioned basic principles.In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with therequirements of this standard, national legislation/regulation takes precedence as illustrated in CEN/TR 13737.NOTE 1 CEN/TR 13737 contains: - clarification of relevant legislation/regulations applicable in a country; - if appropriate, more restrictive national requirements; - national contact point for the latest information.This standard applies to:-- gas installations in residential, commercial and public access building having a maximum operating pressure (MOP) less than or equal to 5 bar;-- industrial gas installations having a maximum operating pressure (MOP) less than or equal to 0,5 bar.NOTE 2 For industrial gas installations having a MOP above 0,5 bar, or installations having a MOP above 5 bar, see prEN15001-1.This standard is applicable to new installation pipework as well as to replacements of, or extensions to, existinginstallation pipework.This standard does not contain detailed recommendations relating to the laying of buried pipework. ~,~NOTE 3 For more information on buried pipework, see EN 12007-1, EN 12007-2 and EN 12007-3.NOTE 4 For more information on gas pressure regulating installations, see EN 12279.NOTE 5 For more information on gas metering systems, see EN 1776.1.2 This standard is applicable to installation pipework supplied from gas distribution systems and from liquefiedpetroleum gases (LPG) storage vessels.Excluded are:-- single appliance LPG installations without fixed pipework, achieved by a flexible appliance connector from an adjacent LPG storage cylinder.-- LPG storage vessels.1.3 In this standard the term 'gas' refers to combustible gases, which are gaseous at 15 ~C and I 013,25 mbar.These gases, odorized for safety reasons, are commonly referred to as manufactured gas, natural gas or liquefiedpetroleum gases (LPG). They are also referred to as first, second or third family gases (see EN 437). 0In this standard, all pressures are gauge pressures, unless otherwise stated.

DIN EN ISO 10414-1-2009石油和天然气工业 钻井液的现场试验 第1部分:水基液

This part of ISO 10414 provides standard procedures for determining the following characteristics ofwater-based drilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) water, oil and solids contents;e) sand content;f) methylene blue capacity;g) pH;h) alkalinity and lime content;i) chloride content;j) total hardness as calcium.Annexes A through K provide additional test methods which may be used for-- chemical analysis for calcium, magnesium, calcium sulfate, sulfide, carbonate and potassium;-- determination of shear strength;-- determination of resistivity;-- removal of air;-- drill-pipe corrosion monitoring;-- sampling, inspection and rejection;-- rig-site sampling;-- calibration and verification of glassware, thermometers, viscometers, retort-kit cup and drilling-fluid balances;-- permeability-plugging testing at high temperature and high pressure for two types of equipment;-- example of a report form for water-based drilling fluid.

BS 6739-2009过程控制系统仪表的实施规范:安装设计和实施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.

BS EN 1775-2007燃气供应.建筑物用燃气管道.大工作压力不超过或等于5 bar.功能性推荐规范

1.1 This standard specifies general recommendations for the design, construction, testing, commissioning,operation and maintenance of installation pipework; pipework between the delivery point of the gas and the inletconnection to the gas appliance.This standard specifies common basic principles for gas installation pipework.Users of this European standard need to be aware that more detailed national standards and/or codes of practicemay exist in the CEN member countries.This standard is intended to be applied in association with these national standards and/or codes of practice settingout the above mentioned basic principles.In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with therequirements of this standard, national legislation/regulation takes precedence as illustrated in CEN /TR 13737.NOTE 1 CEN/TR 13737 contains:- clarification of relevant legislation/regulations applicable in a country;- if appropriate, more restrictive national requirements;- national contact point for the latest information.This standard applies to:- gas installations in residential, commercial and public access building having a maximum operating pressure(MOP) less than or equal to 5 bar;- industrial gas installations having a maximum operating pressure (MOP) less than or equal to 0,5 bar.NOTE 2 For industrial gas installations having a MOP above 0,5 bar, or installations having a MOP above 5 bar, see prEN15001-1.This standard is applicable to new installation pipework as well as to replacements of, or extensions to, existinginstallation pipework.This standard does not contain detailed recommendations relating to the laying of buried pipework.NOTE 3 For more information on buried pipework, see EN 12007-1, EN 12007-2 and EN 12007-3.NOTE 4 For more information on gas pressure regulating installations, see EN 12279.NOTE 5 For more information on gas metering systems, see EN 1776.1.2 This standard is applicable to installation pipework supplied from gas distribution systems and from liquefiedpetroleum gases (LPG) storage vessels.Excluded are:- single appliance LPG installations without fixed pipework, achieved by a flexible appliance connector from anadjacent LPG storage cylinder.- LPG storage vessels.1.3 In this standard the term 'gas' refers to combustible gases, which are gaseous at 15 °C and 1 013,25 mbar.These gases, odorized for safety reasons, are commonly referred to as manufactured gas, natural gas or liquefiedpetroleum gases (LPG). They are also referred to as first, second or third family gases (see EN 437).In this standard, all pressures are gauge pressures, unless otherwise stated.