铜管对流散热器检测

铜管对流散热器检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 16803-2018供暖、通风、空调、净化设备术语

本标准界定了供暖、通风、空调、净化设备的构造、性能通用术语和定义。本标准适用于供暖、通风、空调、净化设备的设计、生产和应用，也适用于供暖、通风、空调、净化设备的科研、教学和出版工作。本标准不适用于锅炉等热源设备和交通工具使用的供暖设备、消烟、排毒设备和通用的风机等通风设备以及交通工具和特殊用途的空调设备。

GB 50333-2013医院洁净手术部建筑技术规范

本规范适用于医院新建、改建、扩建的洁净手术部工程的设计、施工和验收。

GB 50671-2011飞机喷漆机库设计规范

本规范适用于新建、改建和扩建的飞机喷漆机库的设计。

GB 51069-2014中药药品生产厂工程技术规范

本规范适用于新建、改建、扩建的中药药品生产厂房及设施的设计、施工、验收、确认及验证等。

GB 51157-2016物流建筑设计规范

本规范适用于新建、扩建、改建的物流建筑设计。不适用于具有重大危险源的火药、炸药、化工品类的危险品物流建筑。

GB/T 51188-2016建筑与工业给水排水系统安全评价标准

本标准适用于新建、扩建、改建和既有建筑与工业的给水排水系统安全评价。本规范不适用于军工等特殊行业建筑与工业的给水排水系统安全评价。

CECS 224-2007节能型双向集热卫浴间应用技术规程

本规程适用于新建、扩建和改建的民用住宅卫浴间及其他建筑卫浴设施的设计、施工及验收。

CECS 424-2016预制沟槽保温模块地面辐射供暖系统应用技术规程

本规程适用于民用与一般工业建筑以低温热水为热媒或以加热电缆为加热部件的预制沟槽保温模块地面辐射供暖系统的设计、施工和验收。

YC/T 9-2015卷烟厂设计规范

本标准规定了卷烟厂设计的技术要求。本标准适用于卷烟厂技术改造工程设计。

JG/T 221-2016铜管对流散热器

本标准规定了以铜管铝串片为散热元件的自然对流铜管对流散热器(以下简称“对流器”)的术语和定义，分类与标记，材料与结构，要求，试验方法，检验规则，标志、使用说明书和合格证，包装、运输和贮存。本标准适用于工业与民用建筑中，以不高于95 ℃且水质符合GB/T 29044-2012中4.5规定的热水为热媒的对流器。

JG/T 409-2013供冷供暖用辐射板换热器

本标准规定了供冷供暖用辐射板换热器(以下简称辐射板)的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于水温不高于45 ℃,压力不高于0.8 MPa的建筑室内的辐射板。

HJ 508-2009环境标志产品技术要求.采暖散热器

本标准规定了采暖散热器环境标志产品的术语和定义、基本要求、技术内容及其检验方法。本标准适用于工业、民用建筑中，以热水或蒸汽为热媒的采暖散热器，不适用于钢制闭式串片散热器。

JB/T 11248-2012金属复合翅片管对流散热器技术规范

本标准规定了金属复合翅片管对流散热器（简称翅片管对流散热器）的术语和定义、分类、型号、参数、要求、试验方法、检验规则、标志、包装、运输和贮存等。本标准适用于建筑中以热水和蒸汽为热媒的金属复合翅片管对流散热器。

DL 5027-2015电力设备典型消防规程

本规程规定了电力设备及其相关设施的防火和灭火措施，以及消防安全管理要求，适用于发电单位、电网经营单位，以及非电力单位使用电力设备的消防安全管理。电力设计、安装、施工、调试、生产应符合本规程的有关要求。本规程不适用于核能发电单位。

EN 14336-2004建筑物取暖系统.水基取暖系统的安装和交付使用

This document specifies the requirements for the installation and commissioning of water-based heating systems in buildings with a maximum operating temperature of 110 oC and a maximum operating pressure of 6 bar.This document covers the system's requirements for the installation and commissioning of individual components of the system (e.g. heat generators, pumps, controls). It does not cover the specific commissioning requirements for these components.This document does not cover the installation or commissioning of attached systems (e.g. air conditioning, domestic hot water or ventilation systems).This document covers only the technical requirements, and

DIN EN 442-1-2015散热器和对流器.第1部分:技术规范和要求;德文版本EN 442-1-2014

This European Standard defines the technical specifications and requirements of radiators and convectors to be installed in heating systems in buildings including assessment and verification of constancy of performance. This European Standard deals with radiators and convectors installed in a permanent manner in construction works, fed with water or steam at temperatures below 120 °C, supplied by a remote energy source. This European Standard does not apply to independent heating appliances. This European Standard also defines the additional common data that the manufacturer shall provide with the product in order to ensure the correct application of the products.

DIN EN 624-2011专用LPG器具规范.在车辆和船舶上安装的室内密封LPG空间加热装置;德文版本EN 624-2011

This European standard specifies the characteristics of safety, construction, performance and efficiency, the test methods and marking, of room sealed space heating equipment of types C(see CEN/TR 1749)with combustion air intake and outlet for the products of combustion in the wall, roof of floor,combined or not.

DIN EN 15502-2-2-2014燃气中央供暖锅炉.第2-2部分:B1型号用具专门标准.德文版本EN 15502-2-2-2014

This European Standard specifies, the requirements and test methods concerning, in particular the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners and are hereafter referred to as "boilers". Where the word boiler is used, it must be read as the boiler including its connecting ducts, ducts and terminals, if any. This European Standard covers gas-fired central heating boilers type B11, B11BS, B12, B12BS, B13, B13BS according to the classification in CEN/TR 1749:2009: a) that have a nominal heat input (on the basis of net calorific value) not exceeding 70 kW; b) that use one or more combustible gases of the three gas families at the pressures stated in EN 437; c) where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation; d) where the maximum operating pressure in the water circuit does not exceed 6 bar; e) Which can give rise to condensation under certain circumstances; f) which are declared in the installation instructions to be either a "low temperature boiler" or a "standard boiler". If no declaration is given the boiler is to be considered a "standard boiler" g) which are intended to be installed either indoors or in a partially protected place; h) which are either not intended to produce hot water, or are intended to produce hot water either by the instantaneous or storage principle, the whole being marketed as a single unit. i) which are designed for either sealed water systems or for open water systems j) which are either modular boilers, or no modular boilers. This European Standard is to be used in conjunction with the General Requirements Standard EN 15502-1. For applications within the scope of the PED further requirements may be necessary (e. g. situations where the maximum allowable temperature exceeds 110 °C, or where volume times maximum allowa