成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

欧版婴儿学步车-1检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB 14749-2006婴儿学步车安全要求

本标准适用于从能够独立坐到能够自己行走的婴儿使用的婴儿学步车(以下简称学步车)的安全要求和测试方法。 本标准不适用于医疗用学步车以及气垫支撑婴儿的学步车。 婴儿学步车如附有供儿童玩耍的玩具,应符合相关标准要求。

GB/T 22753-2008玩具表面涂层技术条件

本标准规定了玩具表面涂层的技术要求和试验方法。本标准适用于各种具有装饰和防护等功能的玩具表面涂层。本标准不适用于儿童自行车、儿童三轮车、儿童推车、婴儿学步车的表面涂层。

GB 22793.1-2008家具.儿童高椅.第1部分:安全要求

GB 22793的本部分规定了有关家用儿童高椅的安全要求,目的是大限度地减少儿童高椅和用作儿童高椅的多用途高椅在正常使用或合理性可预见误用时导致的事故。本部分不适用于可变换成矮椅,矮椅和矮桌以及具有婴儿学步车、推椅、摇椅、汽车椅和可躺的低椅等高椅的附加功能。本部分不适用于由儿童相互之间在高椅内玩耍可能引起的事故或伤害,或者由3岁以上的儿童滥用或误用时造成的事故。

GB/T 24329-2009出口儿童高椅安全要求及测试方法

本标准规定了出口儿童高椅的安全要求、测试方法及标志、使用说明。本标准适用于供6个月到36个月之间的儿童使用的出口儿童高椅。本标准不适用于以下两种情况:多功能儿童高椅调节成婴儿学步车、推椅、摇椅、汽车座椅及斜躺矮椅等附加功能时;大龄儿童与椅中儿童进行互动或者3岁以上使用者的滥用或不正确使用高椅时。

GB/T 36601-2018电子商务交易产品信息描述 玩具

本标准规定了电子商务交易中玩具类产品信息的描述属性、描述方法、信息模型、通用信息摘要描述、专用信息摘要描述以及信息扩展方法。本标准适用于电子商务中玩具类产品信息的发布、交换、存储和管理等。

CNCA 13C-068-2006玩具类产品强制性认证实施规则.童车类产品

本规则适用于设计或预定供儿童乘骑玩耍的童车类产品,包括:儿童自行车(大鞍座高度在435mm~635mm范围内)儿童三轮车儿童推车婴儿学步车玩具自行车(大鞍座高度小于435mm)电动童车其它玩具车辆

QB/T 2121-2014童车涂层通用技术条件

本标准规定了童车产品(包括儿童自行车、儿童三轮车、儿童推车、婴儿学步车)表面涂层的术语和定义、要求、试验方法。本标准适用于各种具有装饰和防护等功能的童车表面涂层。

SN/T 0729-2014进出口童车检验规程

本标准规定了进出口童车的抽样、检验和检验结果的判定的规则。本标准适用于儿童自行车、儿童三轮车、儿童推车、婴儿学步车的检验。儿童乘骑的童车独轮车、鞍座高度高于435 mm的滑行车、滑板车等的检验可参照本标准执行。本标准不适用于电动童车和其他类童车的检验。

NB/SH/T 0893-2015乘用车直喷柴油发动机油中温分散性评定法

本标准规定了使用标致DV4 TD发动机评定由于烟炱引起的柴油机油黏度增长和活塞清净性的试验方法。本标准适用于评定柴油机油中温分散性能。

ASTM F977-2000婴儿学步车的用户安全使用标准规范

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of the baby walker (see 3.1). 1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of walkers. 1.3 No walker produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4 This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of other persons with the child in the walker or the accidents resulting from abuse and misuse by children able to walk.1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F977-2003婴儿学步车的用户安全使用标准规范

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of the infant walker (see 3.1).1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of walkers.1.3 No walker produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.1.4 This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of other persons with the child in the walker or the accidents resulting from abuse and misuse by children able to walk.1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F977-2009婴儿学步车安规

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of the infant walker (see 3.1). 1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of walkers. 1.3 No walker produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4 This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of other persons with the child in the walker or the accidents resulting from abuse and misuse by children able to walk. 1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F977-2011a婴儿学步车的标准消费者安全规范

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of the infant walker (see 3.1). 1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of walkers. 1.3 No walker produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4 This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of other persons with the child in the walker or the accidents resulting from abuse and misuse by children able to walk. 1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F977-2011b婴儿学步车消费者安全标准规范

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of the infant walker (see 3.1). 1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of walkers. 1.3 No walker produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4 This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of other persons with the child in the walker or the accidents resulting from abuse and misuse by children able to walk. 1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F977-2012婴儿学步车的标准消费者安全规范

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of the infant walker (see 3.1). 1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of walkers. 1.3 No walker produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4 This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of other persons with the child in the walker or the accidents resulting from abuse and misuse by children able to walk. 1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F977-2018婴儿学步车用户安全使用标准规范

1.1x00a0;This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of the infant walker (see 3.1). 1.2x00a0;This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of walkers. 1.3x00a0;No walker produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4x00a0;This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of other persons with the child in the walker or the accidents resulting from abuse and misuse by children able to walk. 1.5x00a0;The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.6x00a0;The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

EN 1273-2005儿童使用和保育用品.婴儿学步车的安全性要求和试验方法

This European Standard specifies safety requirements and test methods for baby walking frames into which a child is placed, and intended to be used from when the child is able to sit up by itself until the child is able to walk by itself.This European Standard does not apply to baby walking frames for therapeutic and curative purposes and to those baby walking frames relying on inflatable parts to support the child. NOTE Baby walking frames relying solely on inflatable parts to support the child are excluded from the scope of this standard because of the problem of retaining rigidity of the structure.This European Standard meets the general safety requirement of Directive 2001/95/EC for the risks it covers (source: 09/18/EGEntsch 2008-12-22, Official Journal of the European Union No. L, p. 30).

上一篇英国婴儿学步车检测 下一篇牙刷及口腔器具检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通