成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

下水道光缆和导管检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 50228-2011工程测量基本术语标准

本标准适用于工程测量及其有关应用领域。

GB/T 50312-2016综合布线系统工程验收规范

本规范适用于新建、扩建和改建建筑与建筑群综合布线系统工程的验收。

GB 50349-2015气田集输设计规范

本规范适用于陆上气田、滩海陆采气田和海上气田陆岸终端集输工程设计。

GB 50660-2011大中型火力发电厂设计规范

本规范适用于蒸汽初参数为超高压及以上、单台机组容量在125MW及以上,采用直接燃烧方式、主要燃用固体化石燃料的火力发电厂工程的设计。

GB/T 51068-2014煤炭工业露天矿机电设备修理设施设计规范

本规范适用于煤炭工业露天煤矿新建、改建及扩建机电设备修理设施工程的设计。

DL 5009.1-2014电力建设安全工作规程.第1部分:火力发电

本部分适用于新建、扩建和改建的火力发电工程建设项目(含核电站常规岛)建筑、安装、调试等安全生产工作。

DL 5334-2006电力工程勘测安全技术规程

本标准规定了电力工程勘测安全技术的基本要求。 本标准适用于电力工程勘测设计工作。

ITU-T L.77-2008在下水道管道中安装光缆.研究小组6

The installation of optical cables inside sewer ducts is basically a trenchless technique.Optical cable installation in sewer ducts presents many advantages compared with traditional trenchinstallation techniques, such as: less time for cable laying, not limited by weather conditions,increased protection of cable against damage, no traffic disruption, no noise pollution, noexcavation, no damage to road surfaces and underground installations, no heavy equipment, noinconvenience to businesses or to citizens.In general, there are two categories of sewers: man-accessible and non-man-accessible sewers.The definition of whether a sewer is man-accessible or not depends not only on national regulations,but also on the individual regulations of different sewer network operators.Usually, non-man-accessible sewers have diameters between 200 mm and 700 mm.Installation in non-man-accessible sewers is carried out with the help of robots. In man-accessiblesewers, both robot-assisted and manual installation of cables is feasible.Basically, there are three different methods to install optical cables into sewer ducts:a) Special armoured optical cables, designed to be directly installed at the bottom of thesewers;b) Self-supporting optical cables, designed to be directly suspended at the top part of sewers;c) Traditional optical cables or micro-cables, designed to be installed in protective ductswhich have to be installed before the cable installation.NOTE 1 – The most important optical cable structures and related performances suitable for these kinds ofinstallation techniques are described in [ITU-T L.78].NOTE 2 – The sewer optical cables and/or related infrastructure should be designed and manufactured for anexpected operating lifetime of at least 15 years. It should be possible to install or remove the cable to/fromthe sewer throughout the operation lifetime. The materials in the sewer optical cable and/or the relatedinfrastructure shall not present a health hazard within its intended use.

ASTM F2303-2003适合于铺设光缆和导管的重力下水道选择的标准实施规范

This practice is intended to assist engineers and sewer owner/operators in determining the suitability of sewers for a secondary use as hosts for optical fiber cables and conduits. It must be kept in mind that the primary use of the sewers is to carry wastewater and/or storm water. Any secondary use of the system shall not significantly impair the primary use. It is up to the engineer to decide upon any exceptions that may be involved in the selection process. Before the selection procedure begins, the installer must have explicit authorization from the owner/operator allowing an evaluation to be conducted for the installation of optical fiber cables or conduits within their sewer system. Engineers and owners should also be cognizant of how the installation of optical fiber cable or conduits will impact the future operational, maintenance and rehabilitation needs of the sewers.1.1 This practice specifically addresses the criteria for determining the suitability of gravity sewers for secondary uses such as the installation of optical fiber systems.1.1.1 This practice applies to the process of selecting gravity sewers that are appropriate for accepting an optical fiber system as opposed to standards for the installation, operation and maintenance of such system within sewers.1.2 This practice applies to both man accessible and man inaccessible sewer systems.1.3 The values stated in inch-pound units are to be regarded as the standard. The values provided in parentheses are for information purposes only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F2303-2003(2009)适合于铺设光缆和导管的重力下水道选择的标准实施规范

This practice is intended to assist engineers and sewer owner/operators in determining the suitability of sewers for a secondary use as hosts for optical fiber cables and conduits. It must be kept in mind that the primary use of the sewers is to carry wastewater or storm water, or both. Any secondary use of the system shall not significantly impair the primary use. It is up to the engineer to decide upon any exceptions that may be involved in the selection process. Before the selection procedure begins, the installer must have explicit authorization from the owner/operator allowing an evaluation to be conducted for the installation of optical fiber cables or conduits within their sewer system. Engineers and owners should also be cognizant of how the installation of optical fiber cable or conduits will impact the future operational, maintenance, and rehabilitation needs of the sewers.1.1 This practice specifically addresses the criteria for determining the suitability of gravity sewers for secondary uses such as the installation of optical fiber systems. 1.1.1 This practice applies to the process of selecting gravity sewers that are appropriate for accepting an optical fiber system as opposed to standards for the installation, operation and maintenance of such system within sewers. 1.2 This practice applies to both man accessible and man inaccessible sewer systems. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F2303-2003(2015)适合于铺设光缆和导管的重力下水道选择的标准实施规程

5.1x00a0;This practice is intended to assist engineers and sewer owner/operators in determining the suitability of sewers for a secondary use as hosts for optical fiber cables and conduits. It must be kept in mind that the primary use of the sewers is to carry wastewater or storm water, or both. Any secondary use of the system shall not significantly impair the primary use. It is up to the engineer to decide upon any exceptions that may be involved in the selection process. 5.2x00a0;Before the selection procedure begins, the installer must have explicit authorization from the owner/operator allowing an evaluation to be conducted for the installation of optical fiber cables or conduits within their sewer system. 5.3x00a0;Engineers and owners should also be cognizant of how the installation of optical fiber cable or conduits will impact the future operational, maintenance, and rehabilitation needs of the sewers. 1.1x00a0;This practice specifically addresses the criteria for determining the suitability of gravity sewers for secondary uses such as the installation of optical fiber systems. 1.1.1x00a0;This practice applies to the process of selecting gravity sewers that are appropriate for accepting an optical fiber system as opposed to standards for the installation, operation and maintenance of such system within sewers. 1.2x00a0;This practice applies to both man accessible and man inaccessible sewer systems. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

NF C93-850-3-40-2015光缆.第3-40部分: 室外光缆. 非人可及的暴风雨和卫生下水道中用采用吹和/或拉的方式安装的下水道光缆和导管的系列规范

La présente partie de la IEC 60794 est une spécification de famille qui s'applique aux câbles en égouts et aux conduites installés par soufflage et/ou tirage dans les évacuations d'eaux pluviales et sanitaires non accessibles par l'homme, elle s'applique également aux égouts et aux conduits secondaires accessibles par l'homme. Les systèmes intégrant des éléments couverts par la présente norme sont soumis aux exigences de la spécification intermédiaire IEC 60794-3.

TS EN 60794-3-40-2015光缆. 第3-40部分: 室外电缆. 非人可及的暴风雨和卫生下水道中用采用吹和/或拉的方式安装的下水道电缆和导管的系列规格

This standar is a family specification that covers sewer cables and conduits for intallation by blowing and/or pulling non-man accessible storm and sanitary sewers.

DIN CLC/TR 50510-2013终端用户光纤通道.FTTx光纤网建造导则.德文版本CLC/TR 50510-2012

The purpose of this Technical Report is to be a first guideline for those considering to install a high bandwidth (high bit-rate) FTTx-network. After studying the Technical Report operators, communities, energy companies, installers and others will understand the necessary steps to take to plan and install FTTx-networks with high quality and cost effectiveness, and to secure a uniform structure and a high quality level on such networks.

BS 6739-2009过程控制系统仪表的实施规范:安装设计和实施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.

上一篇自支持式架空通信光缆检测 下一篇跨越湖泊、河流和沿海用通信光缆检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通