成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

钢和铸铁止回阀检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 8650-2015管线钢和压力容器钢抗氢致开裂评定方法

本标准规定了管线钢和压力容器钢板以及法兰和管件在含有硫化物水溶液的腐蚀环境中,由于腐蚀吸氢引起的氢致开裂(HIC)的评定方法。本标准提供了从每个钢产品类型中取样的尺寸,数量,位置和取向,钢产品的类型包括钢管、钢板、管件和法兰。本标准包括小直径(公称直径[DN]50~150,公称管线尺寸[NPS]为2~6)、薄壁(壁厚不大于6 mm)电阻焊(ERW)和无缝钢管的特殊步骤要求。除非本标准中特殊规定,这些小直径、薄壁材料宜与其他钢管用相同的方法进行试验。本标准不包含接受或者否决的准则,但GB/T 20972.2-2008的第8章提供了指南。

GB/T 31033-2014石油天然气钻井井控技术规范

本标准规定了石油天然气钻井作业的井控技术要求。本标准适用于陆上、滩海石油天然气勘探、开发钻井作业中的油气井压力控制。

GB/T 34001-2016中国修船质量标准

本标准规定了船舶修理过程中的材料使用要求、船舶常规修理对外交验项目、勘验要点、修理质量要求、修理过程质量控制及交验要求。本标准适用于500总吨及以上钢质海洋船舶的常规修理,其他船舶参照使用。本标准不适用于船舶的重大改装。

SY/T 7018-2014控压钻井系统

本标准规定了用于油气井钻井的控压钻井系统的性能、设计、材料、焊接、质量控制、试验和检验、标记、搬运、贮存和运输的要求。本标准适用于控压钻井系统的设计、制造和检验。本标准规定的控压钻井系统配套使用下列工具实现控压钻井作业:a)旋转防喷器;b) 钻具止回阀;c)随钻环空压力测量装置;d)节流、压井管汇。本标准不适用于采用调整钻井液密度控制井眼压力剖面的控压钻井系统。

JB/T 8935-2014工艺流程用压缩机安全要求

本标准规定了工艺流程用压缩机的安全通则、安全装置和防护设备的具体要求。本标准适用于离心、轴流、往复和回转等所有类型的工艺压缩机及其附属设备,包括驱动机、中间冷却器、缓冲器、分离器或净化器、中间连接管路和润滑、密封油及水冷却系统等。本标准不适用于:a)GB 22207-2008《容积式空气压缩机安全要求》规定的空气压缩机;b)压缩机零部件的基本机械设计;c)压缩机相关工艺装置的设计和操作。

EN 16767-2016工业阀门-钢和铸铁止回阀

This European Standard specifies the requirements for cast iron or steel check valves, which are forged, cast or fabricated in straight, angle or oblique pattern (see EN 736-2) with end connections flanged or wafer, butt welding, socket welding, or threaded. This European Standard applies to check valves mainly used for industrial and general purpose applications. However, they may be used for other applications provided the requirements of the relevant performance standards are met. Back flow prevention anti-pollution check valves are outside the scope of this European standard. The range of nominal sizes covered is: DN 8, DN 10; DN 12, DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900; DN 1000. DN 8 and DN 12 are not used for PN designated flanged end connections. DN 8, DN 10 and DN 12 are not used for Class designated flanged end connections. DN 750 is used for Class designated valves only. Socket welding end valves and threaded end valves are limited to the range DN 8 to DN 65. The range of pressure designations covered is: a) for flanged end and wafer type end cast iron bodies:- PN 2,5; PN 6; PN 10; PN 16; PN 25; - Class 125; Class 250; b) for flanged end, wafer type and butt welding end steel bodies; - PN 40; PN 63; PN 100; - Class 150; Class 300; Class 600; c) for socket welding end and threaded end steel bodies; - PN 40; PN 63; PN 100; - Class 600; Class 800. NOTE Class 800 is a widely used Class designation for socket welding and threaded end valves.

TS EN 16767-2016工业阀门. 钢和铸铁止回阀

This European Standard specifies the requirements for cast iron or steel check valves, which are forged, cast or fabricated in straight, angle or oblique pattern (see EN 736-2) with end connections flanged or wafer, butt welding, socket welding, or threaded. This European Standard applies to check valves mainly used for industrial and general purpose applications. However, they may be used for other applications provided the requirements of the relevant performance standards are met. Back flow prevention anti-pollution check valves are outside the scope of this European standard. The range of nominal sizes covered is: DN 8, DN 10; DN 12, DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900; DN 1000. DN 8 and DN 12 are not used for PN designated flanged end connections. DN 8, DN 10 and DN 12 are not used for Class designated flanged end connections. DN 750 is used for Class designated valves only. Socket welding end valves and threaded end valves are limited to the range DN 8 to DN 65. The range of pressure designations covered is: a) for flanged end and wafer type end cast iron bodies:- PN 2,5; PN 6; PN 10; PN 16; PN 25; - Class 125; Class 250; b) for flanged end, wafer type and butt welding end steel bodies; - PN 40; PN 63; PN 100; - Class 150; Class 300; Class 600; c) for socket welding end and threaded end steel bodies; - PN 40; PN 63; PN 100; - Class 600; Class 800. NOTE Class 800 is a widely used Class designation for socket welding and threaded end valves.

DIN EN ISO 13628-1-2010石油和天然气工业.水下生产系统的设计和操作.第1部分:一般要求和推荐规范(ISO 13628-1-2005 + Amd 1-2010).英文版本EN ISO 13628-1-2005 + A1-2010,只光盘版

This part of ISO 13628 provides general requirements and overall recommendations for development of complete subsea production systems, from the design phase to decommissioning and abandonment. This part of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with more detailed requirements for the subsystems which typically form part of a subsea production system. However, in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) more detailed requirements are included herein, as these subjects are not covered in a subsystem standard.

DIN EN ISO 13628-4-2011石油和天然气工业.海底开采系统的设计和操作.第4部分:海底井口装置和采油树设备(ISO 13628-4-2010);英文版本EN ISO 13628-4-2010,仅在CD-ROM上

This part of ISO 13628 provides specifications for subsea wellheads, mudline wellheads, drill-through mudline wellheads and both vertical and horizontal subsea trees. It specifies the associated tooling necessary to handle, test and install the equipment. It also specifies the areas of design, material, welding, quality control (including factory acceptance testing), marking, storing and shipping for both individual sub-assemblies (used to build complete subsea tree assemblies) and complete subsea tree assemblies.The user is responsible for ensuring subsea equipment meets any additional requirements of governmental regulations for the country in which it is installed. This is outside the scope of this part of ISO 13628.Where applicable, this part of ISO 13628 can also be used for equipment on satellite, cluster arrangements and multiple well template applications.

DIN EN ISO 17078-2-2010石油和天然气工业.钻探和生产设备.第2部分:偏心轴的流控制装置(ISO 17078-2-2007+Cor. 1-2009).英文版本EN ISO 17078-2-2007 + AC-2009,仅有光盘版

This European Standard contains requirements on flow control devices for side-pocket mandrels.

上一篇建筑物饮用水用铜合金截止阀检测 下一篇水嘴-PN10自动切断阀检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通