管道和排水用铜合金管检测
GB 16912-2008深度冷冻法生产氧气及相关气体安全技术规程
本规程规定了工业氧气及相关气体的生产(含设计、制造、安装、改造、维修)、储存、输配和使用中应遵守的要求。本规程适用于新建、扩建和改建的采用深度冷冻法生产氧气及相关气体的单位。
GB/T 21481.1-2008船舶与海上技术 船舶和海上结构物上生活用水供应 第1部分: 规划和设计
本部分适用于船舶、固定或漂浮式海上结构物和内河船舶上生活用水供应系统的规划、设计和布置。 本部分规定了为保护生活用水和维持水质所需的生活用水供应系统低要求,并提供了部件使用和管道布置的相关信息。 本部分不涉及生活用水输送的相关规则,生活用水的输送应遵守专门规定。
GB/T 23803-2009石油和天然气工业 海上生产平台管道系统的设计和安装
本标准给出了石油和天然气工业海上生产平台新建管道系统的设计和安装的低要求和指南。管道系统的高压力高达69000kPa(G),在温度范围内对材料的要求满足ASME B31.3的要求。
GB/T 36051-2018燃气过滤器
本标准规定了燃气过滤器产品的分类、代号和型号,结构和材料,要求,试验方法,检验规则及质量证明文件、标志、包装、运输和贮存。本标准适用于公称压力不大于10.0 MPa、公称尺寸不大于600 mm、工作温度范围为-20 ℃~60 ℃燃气输配系统中的燃气过滤器。本标准不适用于石油和(或)天然气生产过程中的气液分离器。
GB 50235-2010工业金属管道工程施工规范
本规范适用于设计压力不大于42MPa,设计温度不超过材料允许使用温度的工业金属管道工程的施工。本规范不适用于下列工业金属管道的施工:1 石油、天然气、地热等勘探和采掘装置的管道;2 长输管道;3 核能装置的专用管道;4 海上设施和矿井的管道;5 采暖通风与空气调节的管道及非圆形截面的管道。
GB/T 50619-2010火力发电厂海水淡化工程设计规范
本规范适用于火力发电厂及核能发电厂的反渗透法和蒸馏法海水淡化系统设计。
GB 50758-2012有色金属加工厂节能设计规范
本规范适用于有色金属加工企业铜、铝加工项目新建、改建和扩建工程的节能设计。
GB/T 51132-2015工业有色金属管道工程施工及质量验收规范
本规范适用于铜、铝、铅、镍、钛、锆、钽、铌及其合金的工业管道工程的施工及质量验收。本规范不适用于下列工业有色金属管道工程的施工及质量验收:1 制造厂成套设计整装于设备的管道。2 军用设施及核能装置的专用管道。3 海上设施和矿井用管道。
CB/T 4034-2005J类外卡式消防接头
本标准规定了法兰连接尺寸按JIS B2240-1996的J类外卡式消防接头(以下简称接头)的分类、要求、试验方法、检验规则、标志和包装。 本标准适用于船舶水消防管路系统用接头的设计、制造和验收。
CECS 171-2004建筑给水铜管管道工程技术规程
本规程适用于新建、改建和扩建的建筑给水(包括生活热水、饮用净水等)铜管管道工程的设计、施工及验收。
CJJ 94-2009城镇燃气室内工程施工与质量验收规范
为统一城镇燃气室内工程的施工与质量验收,保证城镇燃气室内工程的施工质量,确保安全供气,制定本规范。本规范适用于供气压小于或等于0.8MPa(表压)的新建、扩建和改建的城镇居民住宅、商业用户、燃气锅炉房(不含锅炉本体)、实验室、工业企业(不含用气设备)等用户室内燃气管道和用气设备安装的施工与质量验收。
YS/T 5420-2014有色金属工业通用设备安装工程质量检验评定标准
本标准适用于有色金属工业通用设备安装工程质量的检验评定。本标准应与现行行业标准《有色金属工业安装工程质量检验评定统一标准》YS/T 5419配合使用。
ASTM B306-2002铜排水管(DWV)的标准规范
1.1 This specification establishes the requirements for seamless copper tube (DWV) produced from Copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping. Note 18212;Fittings used for soldered or brazed connections in drainage, waste, or vent systems are described in ASME Standards B16.23 and B16.29 and CSA Standard B158.1. Note 28212;The assembly of copper drainage, waste, and vent systems by soldering is described in Practice B 828.Note 38212;Solders for joining copper drainage, waste, or vent systems are described in Specification B 32. The requirement for acceptable fluxes for these systems are described in Specification B 813.1.2 Values stated in inch-pound units are the standard. SI values given in parentheses are for information only.1.3 The following hazard statement pertains only to the test method described in Section 16.2.3 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM B306-2013铜排水管(DWV)标准规格
17.1x00a0;For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29: Property Rounded Unit for Observed or Calculated Value x00a0; 8199;8199;8199;Chemical composition nearest unit in the last right-hand place of 8199;8199;8199;Hardness 8199;figures of the specified limit x00a0; x00a0; 8199;8199;8199;Tensile strength nearest ksi (5 MPa) 1.1x00a0;This specification establishes the requirements for seamless copper tube (DWV) produced from Copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping. Note 1x2014;Fittings used for soldered or brazed connections in drainage, waste, or vent systems are described in ASME Standards B16.23 and B16.29 and CSA Standard B158.1. Note 2x2014;The assembly of copper drainage, waste, and vent systems by soldering is described in Practice B828. Note 3x2014;Solders for joining copper drainage, waste, or vent systems are described in Specification B32. The requirement for acceptable fluxes for these systems are described in Specification B813. 1.2x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
ASTM B698-2002无缝铜和铜合金管和管道的标准分类
This classification is provided to serve the needs of designers, specifiers, installers, and users of seamless copper and copper alloy plumbing tube and piping systems. It familiarizes them with the products available for such systems, giving size ranges and available materials for products listed herein. Also refer to Section 1.1.1 This classification covers various types of seamless copper and copper alloy pipe and tube used for water service, distribution, and drainage. It is not a specification for the various types and alloys.1.2 This classification uses the standard copper designations developed and used by the copper industry.1.3 This classification makes no attempt to differentiate between all compositions that could be termed coppers or copper alloys, but, in conformance with general practice in the trade includes those coppers and copper alloys commonly used in the manufacture of water service, distribution, and drainage pipe and tube.1.4 This classification makes no attempt to differentiate between all applications of seamless copper and copper alloy piping and tubing, and is intended for use in water service distribution and drainage.
ASTM B698-2010无缝铜和铜合金管和管道的标准分类
This classification is provided to serve the needs of designers, specifiers, installers, and users of seamless copper and copper alloy plumbing tube and piping systems. It familiarizes them with the products available for such systems, giving size ranges and available materials for products listed herein. Also refer to Section 1.1.1 This classification covers various types of seamless copper and copper alloy pipe and tube used for water service, distribution, and drainage. It is not a specification for the various types and alloys. 1.2 This classification uses the standard copper designations developed and used by the copper industry. 1.3 This classification makes no attempt to differentiate between all compositions that could be termed coppers or copper alloys, but, in conformance with general practice in the trade includes those coppers and copper alloys commonly used in the manufacture of water service, distribution, and drainage pipe and tube. 1.4 This classification makes no attempt to differentiate between all applications of seamless copper and copper alloy piping and tube intended for use in water service distribution and drainage.
ASTM B698/B698M-2010(2016)e1铜和铜合金无缝管和管件的标准分类
4.1x00a0;This classification is provided to serve the needs of designers, specifiers, installers, and users of seamless copper and copper alloy plumbing tube and piping systems. It familiarizes them with the products available for such systems, giving size ranges and available materials for products listed herein. Also refer to Section 1. 1.1x00a0;This classification covers various types of seamless copper and copper alloy2 pipe and tube used for water service, distribution, and drainage. It is not a specification for the various types and alloys. 1.2x00a0;This classification uses the standard copper designations developed and used by the copper industry. 1.3x00a0;This classification makes no attempt to differentiate between all compositions that could be termed coppers or copper alloys, but, in conformance with general practice in the trade, includes those coppers and copper alloys commonly used in the manufacture of water service, distribution, and drainage pipe and tube. 1.4x00a0;This classification makes no attempt to differentiate between all applications of seamless copper and copper alloy piping and tube intended for use in water service distribution and drainage. 1.5x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
ASTM B828-2002用铜、铜合金管和配件钎焊制作毛细管接缝的标准实施规程
The techniques described herein are used to produce leak-tight soldered joints between copper and copper alloy tube and fittings, either in shop operations or in the field. Skill and knowledge on the part of the operator or mechanic are required to obtain a satisfactorily soldered joint. 1.1 This practice describes a procedure for making capillary joints by soldering of copper and copper alloy tube and fittings. 1.2 This procedure is applicable to pressurized systems such as plumbing, heating, air conditioning, refrigeration, mechanical, fire sprinkler, and other similar systems. ASME B31.5 and B31.9 reference the techniques used for satisfactory joint preparation. It is also used in the assembly of nonpressurized systems such as drainage, waste, and vent. 1.3 It is not applicable to the assembly of electrical or electronic systems. 1.4 Tube and fittings are manufactured within certain tolerances to provide for the small variations in dimensions associated with manufacturing practice. Applicable specifications are listed in Appendix X1. 1.5 A variety of solders are available that will produce sound, leak-tight joints. Choice of solder will depend upon the type of application and on local codes. For potable water systems, only lead-free solders shall be used, some of which are described in Specification B 32. 1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information purposes only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For hazard statements, see the warning statements in 6.4.1, 6.6.1, and 6.6.3.
相关阅读
了解更多检测知识
道桥材料检测
道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。
洗衣凝珠检测
洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。
绿色食品检测
绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。
吐鲁番葡萄检测
吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。
食品过敏原检测
食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。
二硫化钼检测
二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。
我们的优势
选择中析研究所的八大理由
资质齐全
旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。
设备先进
上千台精密仪器定期检定校准,量值溯源体系完善。
专家团队
多领域技术专家,十年以上经验,破解各类疑难检测。
标准覆盖广
覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。
周期短
常规项目7-10个工作日出报告,流程标准高效。
加急服务
支持加急检测通道,助力客户快速完成质量把关。
一对一服务
工程师全程对接,需求沟通到报告解读全流程陪伴。
数据保密
严格保密制度,客户样品与检测数据安全无忧。
旗下实验室资质
我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。
CMA检验检测机构资质认定证书
CNAS实验室认可证书
ISO管理体系认证证书
高新技术企业证书
中国分析测试协会会员单位
中国质量协会会员证书
AAA级信用企业
绿色低碳诚信示范创建企业
仪器设备
1000余台精密设备 · 点击查看原图
气相色谱-质谱联用仪 GC-MS
复杂有机组分的定性鉴定与未知物剖析利器。
高效液相色谱仪 HPLC
食品添加剂、药品成分等热敏物质的精准检测。
电感耦合等离子体发射光谱仪 ICP-OES
一次进样同时读出数十种金属元素含量。
傅里叶变换红外光谱仪 FTIR
通过特征吸收峰快速判断材料种类与分子结构。
X射线荧光光谱仪 XRF
几分钟完成元素快检,且不损伤样品。
扫描电子显微镜 SEM
放大数十万倍观察表面微观结构,锁定失效根源。
液相色谱-质谱联用仪 LC-MS
农兽药残留等痕量物质的高灵敏确证检测。
气相色谱仪 GC
溶剂残留、香气成分等挥发性物质的专业检测。
在线工程师 一对一服务
检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。
NEW · 全新上线
VR实验室上线啦!
720°全景实景观览 · 足不出户走进实验室
立即体验
检测咨询 · 立即在线沟通