气动钳盘式制动器检测

GB/T 6974.14-1986起重机械名词术语 缆索起重机

本标准规定了缆索起重机的专用名词术语。与其他起重机械通用的名词术语见相应的标准。

GB/T 6974.15-1986起重机械名词术语 悬挂单轨系统

本标准规定了悬挂单轨系统的专用名词术语。与其他起重机械通用的名词术语见相应的标准。

GB/T 6974.16-1986起重机械名词术语 冶金起重机

本标准规定了冶金起重机的专用名词术语。与其他起重机械通用的名词术语见相应的标准。

GB/T 6974.17-1986起重机械名词术语 堆垛起重机

本标准规定了堆垛起重机的专门名词术语。与其他起重机械通用的名词术语见相应的有关标准。

GB/T 6974.18-1986起重机械名词术语 港口起重机

本标准规定了水运港口装卸货物专用的起重机名词术语。在港口使用的通用起重机的名词术语见相应的有关标准。

GB/T 6974.19-1986起重机械名词术语 集装箱起重机

本标准规定了集装箱起重机的专用名词术语。与其他起重机械通用的名词术语见相应的有关标准。

GB 12676-2014商用车辆和挂车制动系统技术要求及试验方法

本标准规定了商用车辆和挂车制动系统的技术要求和试验方法。本标准适用于GB/T 15089规定的M<下标2>、M<下标3>及N类机动车辆和O类挂车。本标准不适用于下列车辆:--设计车速不超过25 km/h的车辆;--不能与设计车速超过25 km/h的机动车辆挂接的挂车。

GB 50215-2015煤炭工业矿井设计规范

本规范适用于设计生产能力0.09Mt/a及以上的新建、改建及扩建的煤炭工业矿井的初步可行性研究、可行性研究和设计。

GB 50961-2014有色金属矿山井巷安装工程质量验收规范

本规范适用于有色金属矿山井巷安装工程的质量验收。

MT/T 1097-2008煤矿机电设备检修技术规范

本规范为企业的设备检修提供指导意见,可作为企业制定设备检修细则、检修操作规程和设备完好标准的依据。本规范执行《煤炭法》、《矿山安全法》、《煤矿安全监察条例》、《煤矿安全规程》等煤炭法律、法规、规程和管理标准,执行和有关煤炭行业的所有技术标准。本规范通用部分的技术要求和计量单位等执行或有关行业的技术标准。

CB 4288-2013船厂起重设备安全技术要求

本标准规定了船舶行业各企业用起重设备的安全技术要求。本标准适用于门座起重机、门式起重机、桥式起重机、浮式起重机、汽车起重机、塔式起重机、降机、卷扬机等起重机械的日常检查工作。也适用于自制、改造的起重设备的日常检查工作。其他类型起重设备可参照执行。

JB/T 10426.1-2004风力发电机组.制动系统.第1部分:技术条件

本部分规定了水平轴并网型风力发电机组制动系统的组成形式、工作条件、基本性能、试验方法、检验规则、标志和包装运输等基本要求。　　本部分适用于水平轴并网型风力发电机组由空气制动装置联合传动系统中机械制动装置组成的制动系统，以及由传动系统中低速轴机械制动联合高速轴机械制动装置组成的制动系统。

JB/T 10917-2008钳盘式制动器

本标准规定了钳盘式制动器（以下简称制动器）的术语和定义、型式、技术要求、试验方法和检验规则等。本标准适用于以气缸、液压缸、电磁铁为驱动装置的钳盘式制动器。

JB/ZQ 4746-2006气动钳盘式制动器

气动钳盘式制动器

DIN 19704-1-2014钢制液压结构件.第1部分:设计和计算准则

This standard is to be used for the calculation and construction of hydraulic steel structures consisting of steel constructions, mechanical engineering components and the electric equipment. These structures cover movable sealing devices (\"locks\") including sealings and mountings, the drives and the connecting components between the lock body and the driving devices. This standard is applicable to hydraulic steel structures which are to be built from scratch. If this standard is intended to be applied for purposes of reconstruction, repair or addition of components to existing older steel structures, it shall be distinguished by declaration to which components this standard applies. This standard also applies to inspection covers and components such as intake rakes, bollards, fenders and channel bridges. It may be applied analogously to penstocks including valves and controls. This standard is not applicable to dolphins, training works, shore enclosures, landing piers and offshore structures (e. g. offshore platforms, jack-up platforms). For small and less loaded structures, were the product of multiplying water pressure (in kN/m2) and dam area (in m2) under water weight is less than 50 (in kN), the user may deviate from the requirements of this standard provided there is no objection by the building owner. Requirements for hydraulic steel engineering according to this standard include steel constructions which are under strain of stagnant or flowing waters. They cover movable sealing devices and parts securely connected with the massive type of construction, such as track supports and bearing area. Steel structures build in conjunction with hydraulic steel structures, but which are not exposed to water pressure are to be designed and calculated according to the applicable construction regulations. Requirements for mechanical engineering according to this standard are applicable to machine structures responsible for the movement and the bearings of lock devices, e.

DIN EN 15179-2010轨道交通.制动系.机动车制动系统要求;德文版本EN 15179-2007

This document defines basic requirements for the braking of passenger coaches in trains hauled by locomotives as described in EN 14198, using UIC air brakes (RIC traffic) operating on routes of the European railways and their infrastructure systems.