机械型现场组装式光纤活动连接器检测
GB 50673-2011有色金属冶炼厂电力设计规范
本规范适用于有色金属冶炼厂新建、改建和扩建工程的电力设计。
GB 51204-2016建筑电气工程电磁兼容技术规范
本规范适用于新建、扩建和改建的民用建筑和一般工业建筑的电气工程电磁兼容的设计、施工、检测及验收。
MT 5010-1995煤矿安装工程质量检验评定标准
本标准适用于煤矿矿井及选煤厂的工业设备、钢结构井架、井筒装备、工作压力小于和等于10MPa的工业管道、小于和等于110kV的电气装置、通信、集控和架空索道等安装工程的质量检验评定。本标准主要是根据颁发的有关技术标准和施工验收规范并参照行业有关规范、标准等编制的。本标准未包括的工程项目及设备,建设单位可组织设计、施工单位按照本标准的制定原则,根据设计文件及设备出厂技术文件的要求自行补充临时标准,经省、市、自治区煤炭主管部门批准后执行,并报煤炭工业部备案。
SL 531-2012大坝安全监测仪器安装标准
本标准适用于各级水库大坝嫉测仪器安装与管理。20Om以上或特别重要大坝的安全监测仪器安装应进行专门研究。
JG/T 439-2014家居配线箱
本标准规定了家居配线箱的术语、分类和标记、一般规定、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于住宅套(户)内的家居配线箱。
YD/T 2341.1-2011现场组装式光纤活动连接器.第1部分：机械型
本部分规定了机械型现场组装式光纤活动连接器（又称机械型光纤快速连接器，以下简称机械型现场连接器）的要求、测量和试验、质量评定程序、检验规则、标志、包装、运输及贮存。本部分适用于机械型现场组装式光纤活动连接器。
YD/T 2341.2-2011现场组装式光纤活动连接器.第2部分：热熔型
本部分规定了热熔型现场组装式光纤活动连接器（又称热熔型光纤快速连接器，以下简称热熔型现场连接器）的要求、测量和试验、质量评定程序、检验规则、标志、包装、运输和贮存。本部分适用于热熔型现场连接器。
EN ISO 13628-5-2009石油和天然气工业.水下采油系统的设计和操作.第5部分:海底缆线
This International Standard specifies the general, and some of the special, requirements on materials used for the construction of equipment used in gas welding, cutting and allied processes.
BS EN ISO 13628-5-2009石油和天然气工业.水下采油系统设计和操作.水下脐带管
This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surfacesubsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.This part of ISO 13628 does not apply to a tube or hose rated lower than 7 MPa (1 015 psi).This part of ISO 13628 does not apply to electric cable voltage ratings above standard rated voltagesU0/U(Um) = 3,6/6(7,2) kV rms, where U0, U and Um are as defined in IEC 60502-1 and IEC 60502-2.
