陶瓷釉料检测

陶瓷釉料检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 5000-2018日用陶瓷名词术语

本标准规定了日用陶瓷的名词术语和定义。本标准适用于日用陶瓷。

GB/T 23460.1-2009陶瓷釉料性能测试方法.第1部分:高温流动性测试.熔流法

GB/T 23460的本部分规定了陶瓷釉料高温流动性测试方法 熔流法。本部分适用于建筑卫生陶瓷及日用陶瓷釉料高温流动性的测试。本部分是一个相对的方法，依据本部分所得的试验结果，只有在试验釉与参比釉各项条件相同的情况下测试才具有可比性。

GB/T 29758-2013陶瓷用熔块

本标准规定了陶瓷用熔块的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于陶瓷用熔块。

GB/T 31567-2015用于空气-烟气、烟气-烟气再生式热交换器的搪瓷换热元件

本标准规定了再生式热交换器用搪瓷换热元件在集装前后的低要求。本标准适用于采用湿法浸涂、湿法流动涂搪、湿法喷涂、湿法静电喷涂、湿法电泳涂搪和干粉静电喷涂等各种涂搪工艺的搪瓷换热元件。

YB/T 4500-2016焦炉用大型表面复合预制件

本标准规定了焦炉用大型表面复合预制件的术语和定义、牌号、技术要求、试样制备、试验方法、质量评定程序、包装、标志、运输、储存和质量证明书。本标准适用于莫来石－堇青石质表面附着低膨胀微晶陶瓷釉层大型预制件，也适用于同材质非表面复合大型预制件，主要用于焦炉炉门、装煤口及煤气上升管等热工设备的内衬。

HG/T 4202-2011非颜料用二氧化钛

本标准规定了非颜料用二氧化钛的要求、试验方法、检验规则、标志、标签、包装、运输、贮存。本标准适用于电子元器件、搪瓷工业、化纤工业、电焊条工业、陶瓷釉料工业等行业使用的非颜料用二氧化钛。

HG/T 4822-2022工业硫酸钴

本文件规定了工业硫酸钴的分类、要求、试验方法、检验规则、 标志、标签、包装、运输、贮存。本文件适用于钴精矿、粗制钴盐和含钴废料生产的工业硫酸钴。 该产品主要用于制作电池材料、电子材料及其他钴盐的原料，还用 于陶瓷釉料、油漆催干剂、电镀以及生产含钴颜料等。

HG/T 5551-2019工业三氧化二硼（硼酐）

本标准规定了工业三氧化二硼（硼酐）的要求、试验方法、检验规则、标志、标签、包装、运输、贮存。\r 本标准适用于工业三氧化二硼（硼酐）。该产品主要用于电子玻璃、电子化工的原料，还用于有机合成的催化剂，搪瓷、陶瓷釉料的助熔剂，耐火材料、焊接材料、炉衬材料添加剂，防火涂料阻燃剂，硼铁冶炼等。

JC/T 1046.1-2007建筑卫生陶瓷用色釉料 第1部分:建筑卫生陶瓷用釉料

本标准规定了建筑陶瓷卫生陶瓷用釉料的术语、产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于建筑卫生陶瓷用釉料与熔块。

JC/T 2793-2023球黏土

本文件规定了球黏土的分类、要求、试验方法、检验规则、标志、包装、运输与贮存。\r本文件适用于建筑陶瓷、电瓷、日用陶瓷、卫生陶瓷、耐火材料、陶瓷釉料用天然球黏土和复合球黏土理化性能的测定。其他工业用球黏土也可参照使用。

QB/T 1546-2016陶瓷釉料熔融温度范围测定方法

本标准规定了采用高温显微镜测定陶瓷釉料熔融温度范围的原理与方法。本标准适用于陶瓷釉料和熔剂原料熔融温度范围的测定。

YS/T 949-2014废旧有色金属术语定义

本标准规定了废旧有色金属的术语和定义。本标准适用于废旧有色金属废件、废料的回收、加工和贸易等过程。

ASTM C126-2009陶瓷釉面结构粘土饰面砖，饰面砖和固体砌体装置的标准规范

1.1 This specification covers structural clay load-bearing facing tile and facing brick and other x201C;solid masonry unitsx201D; made from clay, shale, fire-clay, or mixtures thereof, with or without the addition of grog or other mixtures, having a finish consisting of a ceramic glaze fused to the body at above 1500x00B0;F (655x00B0;C) making them inseparable, excluding natural salt-glazed ware. Two grades, based on permissible variation in face dimensions, and two types are covered, as follows: 1.1.1 Grade S (select), for use with comparatively narrow mortar joints. 1.1.2 Grade SS (select sized or ground edge), for use where variation of face dimension must be very small. 1.1.3 Type I (single-faced units), for general use where only one finished face will be exposed. 1.1.4 Type II (two-faced units), for use where two opposite finished faces will be exposed. 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of brick and tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 5) of this standard is beyond the scope of this specification. 1.3 Brick and tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength requirements of this specification. (See firing and fired bond in Terminology C 1232.) 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test portion (Section 15) of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C126-2010陶瓷上釉结构用饰面砖、面砖以及实心砖石砌块标准规范

1.1 This specification covers structural clay load-bearing facing tile and facing brick and other x201C;solid masonry unitsx201D; made from clay, shale, fire-clay, or mixtures thereof, with or without the addition of grog or other mixtures, having a finish consisting of a ceramic glaze fused to the body at above 1500x00B0;F (655x00B0;C) making them inseparable, excluding natural salt-glazed ware. Two grades, based on permissible variation in face dimensions, and two types are covered, as follows: 1.1.1 Grade S (select), for use with comparatively narrow mortar joints.

ASTM C126-2011上釉陶瓷结构用饰面瓷砖,面砖和实心砌块的标准规范

1.1 This specification covers structural clay load-bearing facing tile and facing brick and other x201C;solid masonry unitsx201D; made from clay, shale, fire-clay, or mixtures thereof, with or without the addition of grog or other mixtures, having a finish consisting of a ceramic glaze fused to the body at above 1500x00B0;F (655x00B0;C) making them inseparable, excluding natural salt-glazed ware. Two grades, based on permissible variation in face dimensions, and two types are covered, as follows: 1.1.1 Grade S (select), for use with comparatively narrow mortar joints. 1.1.2 Grade SS (select sized or ground edge), for use where variation of face dimension must be very small. 1.1.3 Type I (single-faced units), for general use where only one finished face will be exposed. 1.1.4 Type II (two-faced units), for use where two opposite finished faces will be exposed. 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of brick and tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 5) of this standard is beyond the scope of this specification. 1.3 Brick and tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test portion (Section 15) of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C126-2012上釉陶瓷结构用饰面瓷砖、面砖和实心砌块的标准规格

1.1x00a0;This specification covers structural clay load-bearing facing tile and facing brick and other x201c;solid masonry unitsx201d; made from clay, shale, fire-clay, or mixtures thereof, with or without the addition of grog or other mixtures, having a finish consisting of a ceramic glaze fused to the body at above 1500x00b0;F (655x00b0;C) making them inseparable, excluding natural salt-glazed ware. Two grades, based on permissible variation in face dimensions, and two types are covered, as follows: 1.1.1x00a0;Grade S (select), for use with comparatively narrow mortar joints. 1.1.2x00a0;Grade SS (select sized or ground edge), for use where variation of face dimension must be very small. 1.1.3x00a0;Type I (single-faced units), for general use where only one finished face will be exposed. 1.1.4x00a0;Type II (two-faced units), for use where two opposite finished faces will be exposed. 1.2x00a0;The property requirements of this specification apply at the time of purchase. The use of results from testing of brick and tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 4) of this standard is beyond the scope of this specification. 1.3x00a0;Brick and tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4x00a0;The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6x00a0;The following precautionary caveat pertains only to the test portion (Section 11) of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C126-2012a上釉陶瓷结构用饰面瓷砖、面砖和实心砌块的标准规格

1.1x00a0;This specification covers structural clay load-bearing facing tile and facing brick and other x201c;solid masonry unitsx201d; made from clay, shale, fire-clay, or mixtures thereof, with or without the addition of grog or other mixtures, having a finish consisting of a ceramic glaze fused to the body at above 1500x00b0;F (655x00b0;C) making them inseparable, excluding natural salt-glazed ware. Two grades, based on permissible variation in face dimensions, and two types are covered, as follows: 1.1.1x00a0;Grade S (select), for use with comparatively narrow mortar joints. 1.1.2x00a0;Grade SS (select sized or ground edge), for use where variation of face dimension must be very small. 1.1.3x00a0;Type I (single-faced units), for general use where only one finished face will be exposed. 1.1.4x00a0;Type II (two-faced units), for use where two opposite finished faces will be exposed. 1.2x00a0;The property requirements of this specification apply at the time of purchase. The use of results from testing of brick and tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 4) of this standard is beyond the scope of this specification. 1.3x00a0;Brick and tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4x00a0;The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6x00a0;The following precautionary caveat pertains only to the test portion (Section 10.2) of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C126-2013上釉陶瓷结构用饰面瓷砖、面砖和实心砌块的标准规格

1.1x00a0;This specification covers structural clay load-bearing facing tile and facing brick and other x201c;solid masonry unitsx201d; made from clay, shale, fire-clay, or mixtures thereof, with or without the addition of grog or other mixtures, having a finish consisting of a ceramic glaze fused to the body at above 1500x00b0;F (655x00b0;C) making them inseparable, excluding natural salt-glazed ware. Two grades, based on permissible variation in face dimensions, and two types are covered, as follows: 1.1.1x00a0;Grade S (select), for use with comparatively narrow mortar joints. 1.1.2x00a0;Grade SS (select sized or ground edge), for use where variation of face dimension must be very small. 1.1.3x00a0;Type I (single-faced units), for general use where only one finished face will be exposed. 1.1.4x00a0;Type II (two-faced units), for use where two opposite finished faces will be exposed. 1.2x00a0;The property requirements of this specification apply at the time of purchase. The use of results from testing of brick and tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 5) of this standard is beyond the scope of this specification. 1.3x00a0;Brick and tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4x00a0;The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6x00a0;The following precautionary caveat pertains only to the test portion (Section 11.2) of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C126-2014内置穿过式金属探测器操作灵敏度设置调整的标准操作规程

1.1x00a0;This specification covers structural clay load-bearing facing tile and facing brick and other x201c;solid masonry unitsx201d; made from clay, shale, fire-clay, or mixtures thereof, with or without the addition of grog or other mixtures, having a finish consisting of a ceramic glaze fused to the body at above 1500x00b0;F (655x00b0;C) making them inseparable, excluding natural salt-glazed ware. Two grades, based on permissible variation in face dimensions, and two types are covered, as follows: 1.1.1x00a0;Grade S (select), for use with comparatively narrow mortar joints. 1.1.2x00a0;Grade SS (select sized or ground edge), for use where variation of face dimension must be very small. 1.1.3x00a0;Type I (single-faced units), for general use where only one finished face will be exposed. 1.1.4x00a0;Type II (two-faced units), for use where two opposite finished faces will be exposed. 1.2x00a0;The property requirements of this specification apply at the time of purchase. The use of results from testing of brick and tile extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 5) of this standard is beyond the scope of this specification. 1.3x00a0;Brick and tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4x00a0;The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6x00a0;The following precautionary caveat pertains only to the test portion (Section 11.2) of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.