船用高压手动球阀检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB 51156-2015液化天然气接收站工程设计规范

本规范适用于陆上新建、扩建和改建的液化天然气接收站工程的设计。

HG/T 20507-2014自动化仪表选型设计规范

本规范适用于化工行业新建、扩建和改造项目中的自动化仪表选型设计。

HG/T 21608-2012液体装卸臂工程技术要求

本标准适用于公称压力CL150、CL300或PN2.5、PN6、PN10、PN16、PN25、PN40、PN63，设计温度-196℃～250℃范围内，通过液体装卸臂实现汽车槽车、火车槽车或槽船装卸各种石油化工液体介质。

CB/T 3191-2013船用高压手动球阀

本标准规定了船用高压手动球阀(以下简称球阀)的分类和标记、要求、试验方法、检验规则、标志与包装。本标准适用于工作压力为6.4 MPa~32 MPa,介质为空气、二氧化碳及液压油等管路系统用球阀的设计、制造和验收。

CB/T 3495.16-1997船舶工业档案管理规则.著录标引细则和主题词表

本标准规定了船舶工业档案著录标引的细则及著录标引用的汉语主题词表。本标准适用于船舶工业档案的著录标引工作。

CB 4288-2013船厂起重设备安全技术要求

本标准规定了船舶行业各企业用起重设备的安全技术要求。本标准适用于门座起重机、门式起重机、桥式起重机、浮式起重机、汽车起重机、塔式起重机、降机、卷扬机等起重机械的日常检查工作。也适用于自制、改造的起重设备的日常检查工作。其他类型起重设备可参照执行。

CB/Z 800-2004船用阀门选用指南

本指导性技术文件给出了船舶动力管路和船舶系统管路中阀门的功能、使用方法、在各管路系统中的选用、安装方法等的指南。\t本指导性技术文件适用于船舶动力管路和船舶系统管路中阀门的选用。

JB/T 3750-1984产品类种划分

本标准适用于机械工业部所生产的产品。作为计划、统计管理工作的产品类中划分的统一依据。本标准不包括大型成套设备。

JB/T 9236-2014工业自动化仪表产品型号编制原则

本标准规定了工业自动化仪表产品(以下简称产品)型号的编制原则。本标准适用于编制产品的型号。本标准不适用于DDZ-S系列仪表、KF系列气动基地式仪表和工业控制计算机系统,它们的型号编制原则另行规定。

EN ISO 13628-1-2005石油和天然气工业.水下采油系统的设计和操作.第1部分:一般要求和建议 ISO 13628-1-2005

This part of ISO 13628 provides general requirements and overall recommendations for development of complete subsea production systems, from the design phase to decommissioning and abandonment.This part of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with more detailed requirements for the subsystems which typically form part of a subsea production system. However, in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) more detailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbons from one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floating or subsea) or onshore, or to inject water/gas through subsea wells.This part of ISO 13628 and its related subsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are not specifically discussed because of their limited use. However, the information presented is applicable to those types of equipment.If requirements as stated inThis part of ISO 13628 are in conflict with, or are inconsistent with, requirements as stated in the relevant complementary parts of ISO 13628, then the specific requirements in the complementary parts take precedence.

DIN EN ISO 13628-7-2007石油和天然气工业.水下采油系统的设计和操作.第7部分:完井/修井提升管系统

This standard gives requirements and recommendations for the design, analysis, materials, fabrication testing and operation of subsea completion/workover (C/WO) riser systems run from a floating vessel.#,,#

BS EN ISO 13628-1-2005+A1-2010石油和天然气工业.水下采油系统的设计和操作.第1部分:一般要求和推荐规范

This part of ISO 13628 provides general requirements and overall recommendations for development ofcomplete subsea production systems, from the design phase to decommissioning and abandonment. Thispart of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with moredetailed requirements for the subsystems which typically form part of a subsea production system. However,in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) moredetailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbonsfrom one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floatingor subsea) or onshore, or to inject water/gas through subsea wells. This part of ISO 13628 and its relatedsubsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are notspecifically discussed because of their limited use. However, the information presented is applicable to thosetypes of equipment.If requirements as stated in this part of ISO 13628 are in conflict with, or are inconsistent with, requirementsas stated in the relevant complementary parts of ISO 13628, then the specific requirements in thecomplementary parts take precedence.