金属移动脚手架检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 24957-2010冷冻轻烃流体船上膜式储罐和独立棱柱形储罐的校准物理测量法

本标准规定了用于运输冷冻轻烃流体的船上膜式储罐和独立棱柱形储罐的内部测量方法。除实际的测量过程外，还规定了用于货物数量计量的校准表和修正表编制的计算程序。对于膜式储罐，本标准的程序是利用安装膜使用的脚手架来支承测量设备，而对于独立棱柱形储罐，应使用其他的安全方式进入到要求测量的位置。

GB 26164.1-2010电业安全工作规程.第1部分：热力和机械

本部分规定了从事电力生产的热力和机械作业的人员在生产现场或工作中的基本安全工作要求。本部分适用于从事电力生产的所有人员和进入电力生产现场的有关人员。

GB/T 50214-2013组合钢模板技术规范

本规范适用于工业与民用建筑及一般构筑物的现浇混凝土工程和预制混凝土构件所用的组合钢模板的设计、制作、施工和验收。

GB 51221-2017城镇污水处理厂工程施工规范

本规范适用于新建、扩建和改建的城镇污水处理厂工程施工。

SH/T 3555-2014石油化工工程钢脚手架搭设安全技术规范

本规范规定了钢脚手架的材料与构配件、通用脚手架结构形式和构造的要求;规定了脚手架结构设计、脚手架的计算、脚手架搭设的施工与管理的要求。本规范适用于石油化工、煤化工、天然气化工等工程建设钢脚手架搭设的结构设计、施工、验收与使用过程的管理。

JGJ/T 275-2013密肋复合板结构技术规程

本规程适用于8层及8层以下且房屋高度不超过24m的多层密肋复合板结构及9层及9层以上或房屋高度超过24m的高层密肋复合板结构。非抗震设计和抗震设防烈度为6度至8度抗震设计的密肋复合板结构,其适用的房屋大高度应符合本规程的有关规定。本规程不适用于建造在危险地段以及发震断裂小避让距离内的密肋复合板结构。

JGJ/T 414-2018建筑施工模板和脚手架试验标准

本标准适用于建筑工程和市政工程用模板、支撑架和脚手架的检验及试验。

JGJ/T 416-2017建筑用真空绝热板应用技术规程

本规程适用于民用建筑中采用建筑用真空绝热板的建筑节能工程的设计、施工及验收。

DB64/ 558-2009建筑工人安全操作规程

本标准规定了建筑工人安全操作的术语和定义、总则、一般规定、架子工、瓦工、抹灰工、石工、木工、钢筋工、混凝土工、普通工、电工、安装电工、防水工、起重吊装工、金属焊割作业工、油漆工、测量工、机械设备维修工、水暖工、铆工、通风工、筑炉工、保温工、桩基施工、大模片施工、钢结构及网架施工、装饰装修施工、拆除施工、土方及筑路机械、桩工机械、吊装及垂直运输机械、混凝土机械、中小型施工机具、市政工程的操作。

DIN-Fachbericht 151-2007技术产品文件.设备管理文件.建筑物文件

The standard describes the extent and the content of the documentation which is handed over when a building is transitioned from the constructionphase to the usingphase.

BS PD CEN/TR 13833-2003施工企业的资格鉴定

This European Standard specifies the definitions, procedures, criteria and their assessment as well as therespective documentation related to a system of qualification of construction enterprises.

ANSI Z245.41-2008废弃物和可回收材料用设备技术和操作.混合的可回收材料的处理设备.安全要求

This American National Standard is applicable to all persons who design, manufacture, assemble, modify,operate, clean, maintain, service, or repair material recovery facilities (MRFs) which engage in receiving,storing, and processing commingled recyclable materials which have been previously collected orotherwise diverted from the solid waste stream. This standard does not apply to scrap processingfacilities (North American Industry Classification system code number 42193, formerly Standard IndustrialClassification number 5093), unless the scrap processing facility operates a MRF, which MRF would thenbe subject to this standard.The safety requirements are divided into 7 sections and are applicable as described in 1.1.1 through1.1.3.1.1.1 Sections 1 through 3 provide general information and definitions and shall apply to all materialrecovery facilities (MRFs) covered by this standard.1.1.2 Sections 4 through 6 provide for physical plant, processing machinery and mobile equipmentrequirements that shall apply to both new and existing MRFs.1.1.3 Section 7 provides for safety programs and safety requirements that shall apply to both new andexisting MRFs.

ANSI/ASSE A10.8-2011脚手架安全要求

This standard establishes safety requirements for the construction, operation, maintenance, and use of scaffolds used in the construction, alteration, demolition, and maintenance of buildings and structures. This standard does not cover permanently installed suspended scaffold systems or aerial platforms. Please note that this standard is based on the 2001 version of the A10.8 Standard, which was administratively withdrawn by ANSI. Since the standard was withdrawn it is viewed/processed as a new standard, but the new document is based on the 2001 administratively withdrawn standard.