成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

铝酸钙水泥熟料检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 201-2015铝酸盐水泥

本标准规定了铝酸盐水泥的术语和定义、分类、材料、技术要求、试验方法、检验规则和包装、标志、运输、贮存与使用等。本标准适用于铝酸盐水泥。

GB/T 4131-2014水泥的命名原则和术语

本标准规定了水泥的分类、命名原则和术语。本标准适用于水泥产品、与水泥性能和试验方法有关的术语。

GB/T 8423.2-2018石油天然气工业术语 第2部分:工程技术

GB/T 8423的本部分界定了石油天然气工业工程技术服务专用的术语及定义。本部分适用于石油天然气工程技术服务领域,石油天然气工业其他领域可参照使用。

GB/T 20472-2006硫铝酸盐水泥

本标准规定了硫铝酸盐水泥的术语与定义、组成材料、强度等级、自应力等级、技术要求、试验方法、检验规则、包装、标志、运输与贮存。 本标准适用于硫铝酸盐水泥。

GB/T 28911-2012石油天然气钻井工程术语

本标准规定了石油天然气钻井工程专用的术语。本标准适用于石油天然气钻井工程领域,也适用于石油天然气工业的其他领域。

GB/T 35162-2017道路基层用缓凝硅酸盐水泥

本标准规定了道路基层用缓凝硅酸盐水泥的术语和定义、组分、材料、强度等级、技术要求、试验方法、检验规则、出厂、交货与验收、包装、标志、运输与贮存等。本标准适用于道路工程施中稳定道路基层与底基层(包括水泥稳定碎石、水泥稳定砂砾、水泥稳定工业废渣、水泥稳定石屑和水泥稳定砂等)。

GB/T 37125-2018硫铝酸盐水泥熟料

本标准规定了硫铝酸盐水泥熟料的术语和定义、分级与代号、要求、试验方法、检验规则、包装、标志、运输和贮存。本标准适用于贸易的硫铝酸盐熟料。

MT/T 420-1995高水充填材料

本标准规定了高水充填材料的产品分类、技术要求、试验方法和检验规则等。\t本标准适用于煤矿巷旁充填用高水充填材料,用于煤矿其他工程的高水充填材料亦可参照使用。

JC/T 437-2010自应力铁铝酸盐水泥

本标准规定了自应力铁铝酸盐水泥的术语和定义、材料、自应力等级、技术要求、试验方法、检验规则和包装、标志、运输与贮存等。

JC/T 1099-2009硫铝酸钙改性硅酸盐水泥

本标准规定了硫铝酸钙改性硅酸盐水泥的术语和定义、组分与材料、强度等级、技术要求、试验方法、检验规则、标志、包装、运输及贮存。本标准适用于硫铝酸钙改性硅酸盐水泥。

JC/T 2282-2014快凝快硬硫铝酸盐水泥

本标准规定了快凝快硬硫铝酸盐水泥的术语和定义、组分和材料要求、强度等级、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于建筑工程、土木工程、道路、隧道、水利等工程紧急抢修及堵漏用的快凝快硬硫铝酸盐水泥。

SL 677-2014水工混凝土施工规范

本标准适用于水利水电工程中1级、2级、3级水工建筑物的混凝土和钢筋混凝土施工,4级、5级水工建筑物可参照执行。

ASTM C1365-2006用X射线粉末衍射分析法测定硅酸盐水泥和硅酸盐水泥熔渣阶段比的标准试验方法

This test method allows direct determination of the proportion of some individual phases in cement or portland-cement clinker. Thus it provides an alternative to the indirect estimation of phase proportion using the equations in Specification C 150 (Annex A1). This test method assumes that the operator is qualified to operate an X-ray diffractometer and to interpret X-ray diffraction spectra. This test method may be used as part of a quality control program in cement manufacturing. This test method may be used in predicting properties and performance of hydrated cement and concrete that are a function of phase composition. QXRD provides a bulk analysis (that is, the weighted average composition of several grams of material). Therefore, results may not agree precisely with results of microscopical methods.1.1 This test method covers direct determination of the proportion by mass of individual phases in portland cement or portland-cement clinker using quantitative X-ray (QXRD) analysis. The following phases are covered by this standard: alite (tricalcium silicate), belite (dicalcium silicate), aluminate (tricalcium aluminate), ferrite (tetracalcium aluminoferrite), periclase (magnesium oxide), gypsum (calcium sulfate dihydrate), bassanite (calcium sulfate hemihydrate), anhydrite (calcium sulfate), and calcite (calcium carbonate).1.2 This test method specifies certain general aspects of the analytical procedure, but does not specify detailed aspects. Recommended procedures are described, but not specified. Regardless of the procedure selected, the user shall demonstrate by analysis of certified reference materials (CRM's) that the particular analytical procedure selected for this purpose qualifies (that is, provides acceptable precision and bias) (see Note 1). The recommended procedures are ones used in the round-robin analyses to determine the precision levels of this test method. Note 0A similar approach was used in the performance requirements for alternative methods for chemical analysis in Test Methods C 114.1.3 The values stated in SI units shall be regarded as the standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards, see Section 9.

ASTM C1365-2006(2011)用X射线粉末衍射分析法测定硅酸盐水泥和硅酸盐水泥熔渣阶段比的标准试验方法

This test method allows direct determination of the proportion of some individual phases in cement or portland-cement clinker. Thus it provides an alternative to the indirect estimation of phase proportion using the equations in Specification C150 (Annex A1). This test method assumes that the operator is qualified to operate an X-ray diffractometer and to interpret X-ray diffraction spectra. This test method may be used as part of a quality control program in cement manufacturing. This test method may be used in predicting properties and performance of hydrated cement and concrete that are a function of phase composition. QXRD provides a bulk analysis (that is, the weighted average composition of several grams of material). Therefore, results may not agree precisely with results of microscopical methods. 1.1 This test method covers direct determination of the proportion by mass of individual phases in portland cement or portland-cement clinker using quantitative X-ray (QXRD) analysis. The following phases are covered by this standard: alite (tricalcium silicate), belite (dicalcium silicate), aluminate (tricalcium aluminate), ferrite (tetracalcium aluminoferrite), periclase (magnesium oxide), gypsum (calcium sulfate dihydrate), bassanite (calcium sulfate hemihydrate), anhydrite (calcium sulfate), and calcite (calcium carbonate). 1.2 This test method specifies certain general aspects of the analytical procedure, but does not specify detailed aspects. Recommended procedures are described, but not specified. Regardless of the procedure selected, the user shall demonstrate by analysis of certified reference materials (CRMx0027;s) that the particular analytical procedure selected for this purpose qualifies (that is, provides acceptable precision and bias) (see Note 1). The recommended procedures are ones used in the round-robin analyses to determine the precision levels of this test method. Note 18212;A similar approach was used in the performance requirements for alternative methods for chemical analysis in Test Methods C114. 1.3 The values stated in SI units shall be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards, see Section 9.

EN 14647-2005铝酸钙水泥.成分,规范和一致性标准

This European Standard gives a general definition of calcium aluminate cement and its composition. It includes requirements for the mechanical, physical and chemical properties and also states the conformity criteria and the related rules.Calcium aluminate cement used as a constituent material of formulated mixes for specific applications (e.g. dry mixes) is outside the scope of this European Standard.

DIN EN 197-1-2011水泥.第1部分:普通水泥的成分,规格和合格标准;德文版本EN 197-1-2011

This European Standard defines and gives the specifications of 27 distinct common cements, 7 sulfate resisting common cements as well as 3 distinct low early strength blast fumace cements and 2 sulfate resisting low early strength alsdt furnace cements and their constituents.

上一篇电解电容器检测 下一篇公共场所及室内空气检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通