电能表用电池检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 15284-2022多费率电能表特殊要求

本文件规定了多费率电能表(以下简称“仪表”)的术语和定义、技术要求、试验方法、检验规则、标识和文件、包装及贮存。本文件适用于新制造的、在电压不超过600 V的50 Hz或60 Hz电网中测量和控制电能的仪表。本文件仅适用于时间开关为数字显示，并用电池或电容等作为工作储备的仪表。本文件不适用于时间开关为模拟标度盘的仪表，也不适用于机电式仪表。

GB/T 20866-2007基于户用脉冲计量表的数据采集器

本标准规定了数据采集器的术语、技术要求、试验方法、检测规则、标志、包装、运输和贮存。本标准适用于数据采集器的设计、制造、试验和检测。本标准中所指的数据采集器是指适用于住宅工商业用户的基于干簧管、光耦、霍尔等脉冲电路技术的电能表、燃气表、自来水表、中水表、直饮水表、热水表、热能表等计量表的信号采集、处理、传输的设备。

GB/T 26831.5-2017社区能源计量抄收系统规范第5部分:无线中继

GB/T 26831的本部分规定了在无线仪表抄读网络中实施中继时的通信协议要求。本部分是GB/T 26831.4的扩充。它支持R2模式的路由，但不支持S模式和T模式的路由。本部分适用于支持无线路由网络的仪表抄读。

GB/T 32856-2016高压电能表通用技术要求

本标准规定了用于测量电压6 kV~35 kV、频率50 Hz的电力网络中高压侧电能的高压电能表(下文简称“仪表”)的术语和定义、电气参数标准值、机械结构要求、环境条件、电气要求、准确度要求、使用和贮存及可靠性要求、检验规则。本标准适用于新制造的高压电能表，并且仅适用于其型式试验。

GB/T 51077-2015电动汽车电池更换站设计规范

本规范适用于电动汽车电池更换站的设计。

CJJ/T 227-2014城市照明自动控制系统技术规范

本规范适用于新建、扩建、改建的城市照明自动控制系统的设计、施工、验收和运行维护。

JTS 196-9-2014集装箱码头堆场装卸设备供电设施建设技术规范

本规范适用于港口集装箱码头堆场装卸设备供电设施的设计、安装和维护。

JJG 691-2014多费率交流电能表检定规程

本规程适用于参比频率为50 Hz或60 Hz的多费率交流电能表(简称多费率表)的首次检定及后续检定。本规程适用于具有数字显示器时间开关的,并用电池(或电容)做备用工作电源的多费率表。对于具有分时计量的多功能电能表,其相同的检定项目执行本规程。本规程不适用于多费率表的现场检验。

YD/T 2312-2011无绳电话机节能参数和测试方法

本标准规定了无绳电话机的座机、子机及子机充电器在各种工作状态下的节能参数和测试方法。本标准适用于接入公众电话网使用的工作频率为45/48MHz、符合GB/T 17113规定的模拟无绳电话机以及工作频率在2.4000～2.4835GHz范围内、符合YD/T1349规定的数字无绳电话机。

DB31/T 1055-2017电动汽车无线充电系统第2部分:设备要求

本部分规定了上海市电动汽车无线充电系统充电站的供电系统、充电位、监控系统、电能计量、通信系统、防护要求、电动汽车无线充电系统地面设施和车载设备的技术要求、检验规则、试验方法、标志、包装和贮运等要求。本部分适用于上海市采用无线充电方式的地面设施和车载设备的配置、订货和检验，亦适用于上海市电动汽车无线充电设施新建、扩建和改建工程，以及电动汽车的生产和改装，也适用于上海市电动汽车无线充电系统的充电站和充电位设计和建设工作。

DIN EN 13757-5-2016仪表通信系统. 第5部分: 无线计量总线中继; 德文版本EN 13757-5-2015

This European Standard specifies the protocols to use when performing relaying in wireless meter readout networks. This European Standard is an extension to wireless meter readout specified in EN 13757-4. It supports the routing of modes P and Q, and simple single-hop repeating of modes S, T, C, F and N. The main use of this European Standard is to support simple retransmission as well as routed wireless networks for the readout of meters. NOTE Electricity meters are not covered by this standard, as the standardization of remote readout of electricity meters is a task for IEC/CENELEC.

BS EN 62055-31-2005电表.付费系统.第31部分:特殊要求.电度表用固定付费系统(1和2类)

This part of IEC 62055 applies to newly manufactured, static watt-hour payment meters of accuracy classes 1 and 2 for direct connection, for the measurement of alternating current electrical energy consumption of a frequency in the range 45 Hz to 65 Hz that include a load switch for the purpose of interruption or restoration of the electricity supply to the load in accordance with the current value of the available credit maintained in the payment meter. It does not apply to static watt-hour payment meters where the voltage across the connection terminals exceeds 600 V (line-to-line voltage for meters for polyphase systems).It applies to payment meters for indoor application only, where the payment meter shall be mounted as for normal service (i.e. together with a specified matching socket where applicable).Payment meters are implementations where all the main functional elements are incorporated in a single enclosure, together with any specified matching socket. There are also multi-part installations where the various main functional elements, such as the measuring element, the user interface unit, token carrier interface, and the load switch are implemented in more than one enclosure, involving additional interfaces. This part of IEC 62055 does not apply to multipart payment metering installations.Functional requirements that apply to payment meters are also defined in this part of IEC 62055, and include informative basic functional requirements and tests for the prepayment mode of operation in Annex A. Allowances are made for the relatively wide range of features, options, alternatives, and implementations that may be found in practice. The diverse nature and functionality of payment meters prevent the comprehensive specification of detailed test methods for all of these requirements. However, in this case, the requirementsare stated in such a way that tests can then be formulated to respect and validate the specific functionality of the payment meter being tested.This part of IEC 62055 does not cover specific functionality or performance requirements for safety, circuit protection, isolation or similar purposes that may be specified through reference to other specifications or standards.This part of IEC 62055 does not cover software requirements. Software requirements for basic energy meter metrology are under consideration for the IEC 62059 series of standards, and in other organisations.This part of IEC 62055 covers type-testing requirements only. For acceptance testing, the concepts given in IEC 61358 may be used as a basic guideline.Dependability aspects are addressed in the IEC 62059 series of standards.This part of IEC 62055 does not cover conformity tests and system compliance tests that may be required in connection with legal or other requirements of some markets.