成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

热电偶用陶瓷绝缘管检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 9316-2007摄影用电子闪光装置安全要求

1.1 本标准给出了电子闪光装置的安全要求。 1.2 本标准适用于储能不超过2000J的不被水滴或水溅的下列摄影用电子闪光装置及其相关装置: a)单个闪光装置,可有一个以上可同时闪亮的闪光头。 b)连续多次曝光摄影用闪光装置。 c)与摄影用电子闪光装置连接的电池充电器和电源装置;它可能是电源插头的一部分。 d)附属装置,例如:说明书中列举的光量调节器及闪光同步器等。 本标准不适用于频闪装置。 就电源而言,适用于下列几种类型: a)用电网电源工作的闪光装置; b)用电池工作的闪光装置; c)电网电源和电池均可用的闪光装置。 1.3 本标准不适用于对地额定电源电压超过250V(有效值)的装置。 1.4 本标准仅涉及闪光装置的安全不涉及其他性能(见第3章)。

GB/T 9978.1-2008建筑构件耐火试验方法.第1部分:通用要求

GB/T的本部分规定了各种结构构件在标准受火条件下确定其耐火性能的试验方法。

GB/T 18036-2008铂铑热电偶细丝的热电动势测量方法

本标准规定了用熔丝法和比较法测量铂铑热电偶丝热电动势的方法。本标准适用于测量直径为0.05mm~0.1mm范围内的铂铑热电偶细丝。其他贵金属和贱金属热电偶细丝的热电动势测量也可参照进行。

GB 19510.1-2009灯的控制装置 第1部分:一般要求和安全要求

本部分规定了使用250V以下直流电或50H<下标z>或60H<下标z>的1000V以下交流电的灯的控制装置的一般要求和安全要求。本部分还适用于尚未标准化的灯所使用的控制装置。本部分涉及的试验均为型式试验。

GB/T 30429-2013工业热电偶

本标准规定了工业热电偶的分类、技术要求、试验方法、检验规则、包装和标志。本标准适用于分度表和允差符合GB/T 16839.1和GB/T 16839.2的可拆卸的、主要用于氧化气氛的工业热电偶。对于其他型式的工业热电偶,可参照采用本标准的全部或部分条文。

GB 51037-2014微组装生产线工艺设备安装工程施工及验收规范

本规范适用于新建、改建及扩建的微组装生产线工艺设备的安装工程施工、调试、试运行及验收。

GB 51145-2015煤矿电气设备安装工程施工与验收规范

本规范适用于煤矿建设电气设备安装工程的施工及验收。

JJF 1184-2007热电偶检定炉温度场测试技术规范

本规范适用于(300~1500)℃范围内包括带温控器和不带温控器的卧式管式热电 偶检定炉(以下简称检定炉)温度场的测试。对于立式管式检定炉、退火炉的温度场测试,可参照本规范执行。

JB/T 7494-1994仪器仪表材料产品分类

本标准规定了引用标准、分类规则、产品分类。 本标准适用于仪器仪表材料产品,可作为计划、统计、管理、标准制订的依据。

UL 17-2008燃油器具用通风或烟囱连接件调节器

The dodument cover requirements for electrically operated damper assemblies, that are intended for installation in the vent or chimney connector of automatically operated oil-fired appliances employing an atomizing type oil burner. The damper assembly is intended to restrict or block the connector opening when the burner is not firing. These requirements cover automatic vent or chimney connector dampers for oil-fired appliances having a flue gas temperature not in excess of 538 ?C (1000 ?F), unless marked for a lower temperature. The vent or chimney connector dampers covered under these requirements are not for use on oil-fired appliances that employ vaporizing type oil burners. Automatic vent or chimney connector dampers are intended for installation in accordance with the following standards of the National Fire Protection Association: a) Oil-Burning Equipment, NFPA 31. b) Chimneys, Fireplaces, and Vents, NFPA 211. c) National Electrical Code, ANSI/NFPA 70. A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-product requirements to maintain the level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

UL 38-2008火灾报警系统用手动信令盒

1.1 These requirements cover manual signaling boxes for fire alarm systems intended for permanentinstallation and used in ordinary locations in accordance with the National Electrical Code, NFPA 70, and the National Fire Alarm Code, NFPA 72.1.2 A manual signaling box is an assembly of a mechanism having electrical contacts designed totransmit a signal when an integral part is operated manually. The signaling contacts are intended to beconnected to circuits of fire alarm systems. The types of boxes covered by these requirements are coded boxes and non-coded boxes, including signaling boxes, fire and guard’s tour reporting stations, and guard’s tour reporting stations for suppressed-signal tour combinations.1.3 A manual signaling box having a pre-wound signaling mechanism and equipped with a trippingelectromagnet to permit automatic actuation by separate detectors, and similar combination devices, shall be evaluated with regard to compliance with the applicable requirements for both manual signaling boxes and electrically-actuated transmitters.1.4 A manual signaling box shall be constructed for use with system-control units, electrically-actuatedtransmitters, or similar units that will permit its application in compliance with applicable codes andstandards of the National Fire Protection Association.1.5 These requirements do not cover electrically-actuated transmitters.

UL 296-2003燃油炉

These revisions are to the UL 296 proposals announced in the March 18, 2005 issue of ANSI's \"Standards Action.

UL 346-2005防火信号系统用水流量指示器

1.1 These requirements cover vane type waterflow indicators intended for use in fire protective signaling systems to be employed in ordinary indoor locations, in accordance with the National Fire Alarm Code, NFPA 72. 1.2 Waterflow indicators covered by these requirements include sizes 3/4 inch and larger. The indicator sizes refer to the nominal inside diameter of the main sprinkler pipe or tubing on which they are installed. 1.3 A vane type waterflow indicator is an assembly of a mechanism having electrical contacts arranged to transmit a coded or noncoded signal when the vane, located in the supply pipe (riser) of a sprinkler system, is moved by the flow of water in the pipe. This flow is normally caused by the opening of one or more sprinkler heads resulting from a fire condition. The signaling contacts are intended to be connected to circuits of private fire protective signaling systems. 1.4 These requirements do not cover pressure-operated waterflow indicators.

上一篇氮化硅陶瓷密封环检测 下一篇碳化硅密封环检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通