多功能控制装阀检测

GB/T 10827.1-2014工业车辆 安全要求和验证 第1部分:自行式工业车辆(除无人驾驶车辆、伸缩臂式叉车和载运车)

GB 10827的本部分规定了如ISO 5053所定义的下列自行式工业车辆(以下简称“车辆”)的安全要求及其验证方法:a) 平衡重式叉车;b) 前移式叉车(具有可伸缩的门架或货叉架);c) 插腿式叉车;d) 托盘堆垛车;e) 高起升平台搬运车;f) 操作台起升高度不大于1 200 mm的车辆;g) 侧面式叉车(单侧);h) 侧面堆垛式叉车(两侧和三向);i) 托盘搬运车;j) 双向和多向运行叉车;k) 牵引力不大于20 000N的牵引车;l) 平衡重式越野叉车;m) 其他以蓄电池、柴油、汽油或液化石油气为动力的工业车辆。对于操作台起升高度大于1 200 mm的车辆和/或带着载荷起升至1 200 mm以上运行的车辆,本部分应与ISO 3691-3一起使用。本部分不适用于自行式伸缩臂式叉车、无人驾驶车辆和载运车,ISO 3691-2、ISO 3691-4和ISO 3691-6分别适用于这些车辆。本部分不适用于在苛刻条件下(如极端天气、冷库应用、危险环境)工作的车辆,这些情况需要有特殊防护措施。本部分涉及了除以下情形外,有关机械在制造商预期用途下使用和可预见条件下误用的,如附录B所列的所有重大危险、危险状态或危险事件。本部分不包括下列情况可能发生的危险:--在制造过程中;--搬运能自由摆动的悬吊载荷时;--在公路上使用时;--在潜在爆炸性环境中操作时;--在与货架之间的单侧间隙小于500 mm的狭窄通道上使用时;--驾驶拖曳载荷的坐驾式车辆时,由于采用非人类工效学姿势而引起;--驾驶额定起重量大于10 000 kg

GB/T 14536.9-2008家用和类似用途电自动控制器. 电动水阀的特殊要求(包括机械要求)

GB 14536.1-2008中的该章，用下述内容代替：1.1本部分适用于家用和类似用途设备中或随这些设备一起使用的电动水阀，这些设备可以是使用电、燃气、油、固体燃料、太阳能等能源或是它们的组合，应用范围包括加热、空气调节及类似用途。本部分也适用于GB 4706所涉及的各类器具用的电动水阀。1.1.1本部分包含了对水阀的电气性能和阀的机械性能的要求，这两者会影响水阀预期操作。1.1.2本部分适用于电动水阀固有的安全性，适用于涉及到设备保护的操作值和操作程序，适用于家用和类似用途设备中或随这些设备一起使用的电自动控制器的试验。对于非一般家用设备用电动阀，而这些设备是由诸如商店或轻工工厂或农场的非农场的非人员使用的，也包含在本部分范围内。本部分不适用于专门用于工业设备的电动水阀。本部分不适用于：标称连接尺寸在DN 50以上的电动水阀；标称允许压力值在1.6Mpa以上的电动水阀；食品分配器；洗涤剂分配器；蒸汽阀。在本部分中，当不会引起误解时，下列术语有其特定含义：——“阀”一词指电动水阀（包括起动器和阀体组件）。——“起动器”一词意思是“电动机构或原动机构”。——“阀体”一词意思是“阀体组件”。——“设备”一词包括器具和控制系统。1.1.3本部分适用于起动器和相互匹配的阀体。1.1.4本部分适用于单个的阀、作为系统部件的阀和与多功能控制器机械地组合在一起的无电气输出的阀。

GB/T 14536.21-2008家用和类似用途电自动控制器.电动油阀的特殊要求，包括机械要求

GB 14536.1中的该章，用下述内容代替: 代替: 1. 1本部分适用于家用和类似用途设备中或随这些设备一起使用的电动油阀，这些设备可以是使用电、燃气、油、固体燃料、太阳能等能源或是它们的组合，应用范围包括加热、空气调节及类似用途。 本部分也适用于使用NTC或PTC热敏电阻的电动油阀，其要求包含在附录J中。 1.1.1本部分适用于电动油阀固有的安全性，适用于涉及到设备保护的操作值和操作程序，适用于家用和类似用途设备中或随这些设备一起使用的电自动控制器的试验。也适用于工业用途的，没有相应 标准的，如中央加热、空调、热处理等用的电动油阀。 本部分也适用于GB 4706.1所涉及的各类器具用的电动油阀。 本部分包含了对油阀的电气性能和阀的机械性能的要求，这两者会影响油阀预期操作。 本部分不适用于专门用于工业设备的电动油阀。 对于非一般家用设备用电动油阀，而这些设备是由诸如商店或轻工工厂或农场的非人员使用的，也包含在本部分范围内。本部分说明了一些机械特征在\"在考虑中\"。直到机械要求包含在本部分中，每个使用本部分的应说明这些要求。 1.1.2本部分适用于那些人工控制器，当其电气上或机械上构成电动油阀。 本部分不适用于标称连接尺寸在DN 150以上的电动油阀。\"阀\"一词指电动油阀(包括原动机构和阀体组件)。 1.1.3与电动油阀一起送到测试试验室的电起动器在本部分中评估。独立的电起动器在GB 14536.16 中评估，该标准为电起动器的特殊要求。 1.1.4本部分适用于单个的阀、作为系统部件的阀和与多功能控制器机械地组合在一起的无电气输出的阀。

GB/T 30597-2014燃气燃烧器和燃烧器具用安全和控制装置通用要求

本标准规定了使用GB/T 13611规定的城镇燃气的燃气燃烧器和燃烧器具用安全和控制装置及其组件(以下简称“控制装置”)的术语和定义、分类和分组、结构和材料、要求、试验方法、标识、安装和操作说明书、包装、运输和贮存。本标准适用于以下控制装置:--自动和半自动阀;--燃烧控制装置;--熄火保护装置;--燃气和空气比例调节装置;--压力调节装置;--旋塞阀总成;--温度控制装置;--多功能控制装置;--压力传感装置;--阀门检验系统。

HG/T 20505-2014过程测量与控制仪表的功能标志及图形符号

本标准适用于化工自控设计中仪表回路号、仪表位号的编制以及仪表图形符号的规定及应用。

CJ/T 336-2010冷凝式家用燃气快速热水器

本标准规定了加热生活用水的冷凝式家用燃气快速热水器的分类和型号、材料和结构、要求、试验方法、验收规则及标志和说明书、包装、运输和贮存。本标准适用于除人工煤气之外符合GB/T 13611规定燃气、额定热输入不大于70kW的强制排气式冷凝热水器、强制给排气式冷凝热水器和室外型冷凝热水器。

HB 7504.10-1997飞行模拟器设计和性能的数据要求 液压系统

本标准规定了飞行模拟器液压系统的数据要求。　　本标准适用于民用飞机飞行模拟器，军用模拟器可参照使用。　　本标准为飞行模拟器承制方、使用方、飞机设备的订购方和有关管理机构，提供建造和验证符合空勤人员训练要求的、足够逼真的飞行模拟器所必须的数据范围和内容。　　本标准不是确定飞行模拟器数据要求的唯一方法。

SL/T 244-1999水文缆道机电设备及测验仪器通用技术条件

本标准规定了适用于水面宽500m、水深30m,流速5m/s、吊重400kg以下的中小型江河水文缆道测验设备及仪器的定义、分类、组成、型号命名、技术要求、试验方法、检验规则及标志、包装、运输、贮存等要求。

NB/T 20358.8-2018核电厂建设工程预算定额 第8部分:核岛自动化控制仪表安装工程

本部分规定了核电厂建设工程预算定额中的核岛自动化控制仪表安装工程定额。本部分适用于压水堆核电机组新建、扩建工程的核岛工程，以及BOP工程中的核岛废液贮罐厂房、常规岛废液贮罐厂房、放射性固体废物处理辅助厂房、固体废物暂存库、放射性机修及去污车间等有核安全要求的子项。其他核电堆型和核工程可参考使用。

EN 30-1-1-2008家用燃气灶具.第1-1部分:安全性.一般性;包含修改件A1-2010

This European Standard specifies the construction and performance characteristics as well as the requirements and methods of test for the safety and marking of freestanding and built-in domestic cooking appliances burning the combustible gases given in 4.1 according to the categories specified in 4.2, referred to in the text as \"appliances\".This European Standard covers the following types of domestic cooking appliances, as defined in Clause 3, and belonging to the classes defined in 4.3 (see Table 1): independent freestanding hotplates; independent built-in hotplates; independent hotplates and grills; table cookers; freestanding ovens; built-in ovens; freestanding or built-in grills; griddles; freestanding cookers; built-in cookers. Unless specifically excluded hereafter,This European Standard applies to these appliances or their component parts, whether or not the component parts are independent or incorporated into a single appliance, even if the other heating components of the appliance use electrical energy (e. g. combined gas-electric cookers).This European Standard includes requirements covering the electrical safety of equipment incorporated in the appliance that is associated with the use of gas. It does not include requirements covering the electrical safety of electrically-heated component parts or their associated equipment1).This European Standard does not apply to: a) outdoor appliances; b) appliances connected to a combustion products evacuation duct; c) appliances having a pyrolitic gas oven; d) appliances having covered burners which are not in conformity with the constructional requirements of 5.2.8.2.2; e) appliances incorporating flame supervision devices and having an automatic ignition device for which the duration of the ignition attempt is limited by design; f) appliances equipped with a burner that is periodically ignited and extinguished under the control of an automatic on/off device; 1) Refer to the electrical safety rules. g) appliances equipped with an oven and/or with a grill having a fan: 1) either for the supply of combustion air or for the evacuation of the products of combustion; 2) or for the circulation of the products of combustion within the compartments; h) appliances supplied at pressures greater than those defined in 7.; i) appliances having one or more burners that are capable of remote operation (type1 or type 2), unless the burner(s) concerned are thermostatically controlled oven burners of time-controlled ovens that are designed for a delayed start without the user being present; j) appliances incorporating one or more hotplate or grill burners that enable the user to program the cooking cycle, including the start and/or the end of the cycle.This European Standard does not cover the requirements relating to third family gas cylinders, their regulators and their connection.This European Standard only covers type testing.

NF D35-354-2008专用液化石油气装置用规范.家用无烟道空间加热器(包括扩散式催化燃烧加热器)

La présente Norme européenne spécifie les prescriptions, les méthodes d'essais et le marquage des appareils domestiques de chauffage non raccordés à un conduit d'évacuation des produits de la combustion, y compris les appareils à combustion catalytique diffusive, dont le débit calorifique nominal est inférieur à 4,2 kW (HS), alimentés par des gaz de la 3e famille sous la pression nominale de service ne dépassant pas 50 mbar, désignés dans le texte par \"appareils\".La présente Norme européenne est applicable aux types d'appareils suivants : appareils fixes fonctionnant au butane commercial et/ou au propane commercial ; appareils portatifs ou mobiles fonctionnant soit au butane commercial, soit au butane commercial et au propane commercial, y compris ceux qui ont un compartiment d'installation pour une bouteille portative rechargeable de gaz de pétrole liquéfié.Aucune prescription particulière concernant le rendement thermique n'est définie pour ces types d'appareils car toute la chaleur produite par le processus de la combustion se dégage dans l'espace à chauffer ; les exigences concernant la combustion, qui relèvent de la sécurité, garantissent la combustion du combustible gazeux.La présente Norme européenne ne concerne pas les appareils incorporant des dispositifs électriques de contrôle du gaz.L'annexe A donne les détails concernant les catégories d'appareils commercialisées dans les divers pays.Les exigences pour les appareils données dans cette norme européenne supposent que l'alimentation en gaz à partir de la bouteille soit contrôlée par un détendeur dont la pression nominale maximale de détente atteint 50 mbar.La présente norme européenne ne concerne pas les bouteilles de gaz de pétrole liquéfié, ni leurs détendeurs associés, ni les tubes et tuyaux flexibles, qui doivent être conformes aux réglementations nationales en vigueur. La présente norme couvre uniquement les essais de type.

DIN EN 449-2008专用液化石油气装置用规范.无排气口的居室暖器(包括扩散催化燃烧的加热器)

This European Standard specifies the requirements, the test methods and the marking of domestic flueless spaceheaters, including diffusive catalytic combustion heaters, having a nominal heat input (Hs), not exceeding 4,2 kWburning 3rd family gases at nominal operating pressures not exceeding 50 mbar. referred to in the text as'appliances'.This European Standard is applicable to the following types of appliances:a) fixed heaters burning commercial butane and/or commercial propane;b) portable or mobile heaters burning either commercial butane, or, commercial butane and commercial propane including those that incorporate a LPG container installation compartment for a transportable refillable liquefied petroleum LPG container.There are no specific thermal efficiency requirements appropriate to these types of appliance as:c) all the heat produced by the combustion process is released into the space to be heated;d) the requirements with regard to the combustion performance, which is a safety matter, ensure the effective burning of the fuel gas.It does not cover appliances incorporating electrically operated gas control systems.Annex A gives the details of the categories of appliances marketed in various countries.Requirements for appliances given in this standard assume that the supply of gas from the container will begoverned by a pressure regulator having a maximum nominal outlet pressure of 50 mbar.This European Standard does not cover LPG containers for liquefied petroleum gas neither their associatedregulator nor tubing and flexible hoses which shall comply with national requirements in force.This European Standard only covers type testing.

DIN EN 13278-2014前开式独置燃气加热器.德文版本EN 13278-2013

This European Standard specifies the requirements and test methods for the construction, safety, marking and rational use of energy of open fronted gas-fired independent space heaters with and without a fan to assist with the transportation of flue gases. Although the fan may be mounted outdoors, this standard only covers appliances where the body of the appliance is indoors. This standard applies to types B11AS, B11BS, B14AS, and B14BS open fronted gas-fired independent space heating appliances that incorporate an atmospheric burner, that are connected directly to an open flue or to a device to evacuate the products of combustion (open-flued appliances), that have a nominal heat input not exceeding 20 kW (based on the net calorific value) and that are delivered with the gas-carrying components, burner (s), combustion chamber and heat exchanger fully assembled.

BS EN 449-2002+A1-2007专用液化石油气设施的规范.家用无烟道空间加热器(包括扩散式催化燃烧加热器)

This European Standard specifies the requirements, the test methods and the marking of domestic flueless spaceheaters, including diffusive catalytic combustion heaters, having a nominal heat input (Hs), not exceeding 4,2 kWburning 3rd family gases at nominal operating pressures not exceeding 50 mbar, referred to in the text as'appliances'.This European Standard is applicable to the following types of appliances:a) fixed heaters burning commercial butane and/or commercial propane;b) portable or mobile heaters burning either commercial butane, or, commercial butane and commercial propaneincluding those that incorporate a LPG container installation compartment for a transportable refillable liquefiedpetroleum LPG container.There are no specific thermal efficiency requirements appropriate to these types of appliance as:c) all the heat produced by the combustion process is released into the space to be heated;d) the requirements with regard to the combustion performance, which is a safety matter, ensure the effectiveburning of the fuel gas.It does not cover appliances incorporating electrically operated gas control systems.Annex A gives the details of the categories of appliances marketed in various countries.Requirements for appliances given in this standard assume that the supply of gas from the container will begoverned by a pressure regulator having a maximum nominal outlet pressure of 50 mbar.This European Standard does not cover LPG containers for liquefied petroleum gas neither their associatedregulator nor tubing and flexible hoses which shall comply with national requirements in force.This European Standard only covers type testing.

BS EN 656-2000燃气集中供暖锅炉.标称热输入值70KW-300KW的B型锅炉

This standard specifies the requirements and test methods concerning, in particular the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as \"boilers\".\nThis standard applies to boilers of type B, as listed in 4.2:\n- that use one or more combustible gases of the three gas families at the pressures stated in Tables 14 and 15;\n- that have a nominal heat input (net CV basis) exceeding 70 kW, but not exceeding 300 kW, including modular boilers;\n- where the temperature of the heat transfer fluid does not exceed 105 ℃ during normal operation;\n- where the maximum operating pressure in the water circuit does not exceed 6 bar.\nThe standard applies to boilers designed for sealed water systems or for open water systems.\nThe standard does not contain all the requirements necessary for boilers:\n- intended to be installed in the open or in living rooms;\n- permanently fitted with more than one flue outlet;\n- where the combustion circuit is sealed with respect to the room where the boiler is installed;\n- of the condensing type;\n- of the low temperature type;\n- intended to be connected to a common flue having mechanical extraction;\n- fitted with a forced draught burner in accordance with EN 676;\n- producing hot water for domestic purposes.\nThis standard only covers type testing.