十字螺丝刀检测

GB/T 32442-2015可拆装家具拆装技术要求

本标准规定了可拆装家具的术语和定义、安装技术要求、装配精度要求、拆卸技术要求及包装、运输和贮存。本标准适用于木制材料为基材或木制材料与部分金属材料相结合的可拆装家具，并以典型可拆装家具产品为例进行详述，其他各类可拆装家具产品可参照执行。

GB/T 37410-2019地面用太阳能光伏组件接线盒技术条件

本标准规定了地面用太阳能光伏组件接线盒的结构要求和性能要求，以及测试方法。本标准适用于直流电压小于或等于1 500 V且符合标准GB/T 20047.1—2006中应用等级Ⅱ的光伏组件用接线盒。安装在组件上用于控制、监视或者类似操作的电子装置，可参考本标准。

GA 885-2010公安单警装备.警用制式刀具

本标准规定了公安单警装备警用制式刀具的术语和定义、编号、技术要求、试验方法、检验规则及包装、运输与贮存。本标准适用于公安单警装备警用制式刀具的生产、检验与订购。

UL 346-2005防火信号系统用水流量指示器

1.1 These requirements cover vane type waterflow indicators intended for use in fire protective signaling systems to be employed in ordinary indoor locations, in accordance with the National Fire Alarm Code, NFPA 72. 1.2 Waterflow indicators covered by these requirements include sizes 3/4 inch and larger. The indicator sizes refer to the nominal inside diameter of the main sprinkler pipe or tubing on which they are installed. 1.3 A vane type waterflow indicator is an assembly of a mechanism having electrical contacts arranged to transmit a coded or noncoded signal when the vane, located in the supply pipe (riser) of a sprinkler system, is moved by the flow of water in the pipe. This flow is normally caused by the opening of one or more sprinkler heads resulting from a fire condition. The signaling contacts are intended to be connected to circuits of private fire protective signaling systems. 1.4 These requirements do not cover pressure-operated waterflow indicators.

UL 2097-2006电子设备用双绝缘系统的参考标准

These requirements cover double insulation systems intended for use in ungrounded electronic equipment marked \"Double Insulation,\" \"Double Insulated,\" or with the double-insulation symbol intended to be employed in accordance with the National Electrical Code, ANSI/NFPA 70. Equipment marked \"Double Insulation,\" \"Double Insulated,\" or with the double-insulation symbol shall comply with the applicable requirements in this standard and in the standard covering the particular type of equipment - the end-product standard. In cases where the end-product standard contains requirements for double insulation, the end-product standard takes precedence. It is intended that the requirements in this standard be applied to end products marked as described unless the end-product standard specifies different requirements. These requirements were developed for categories that do not have double insulation requirements, to provide guidance about double insulation systems, and to promote consistent approaches to double insulation. Double insulation requirements for electronic equipment are applicable to the double insulation systems used in products contained in various end-product, component and systems standards. Guidelines and Applications for Double Insulation Systems for Electronic Equipment in Appendix a covers: a) Level of Protection Provided by Double Insulation, b) Methods to Address Product-Specific Double Insulation Requirements, and c) Guidelines for Including Double Insulation Requirements in an End-Product Standard. A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire, electric shock, or injury to persons shall be evaluated using the appropriate additional component and end-product requirements to determine that the level of safety as originally anticipated by the intent of this standard is maintained. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard shall not be judged to comply with this standard. Where appropriate, revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

STAS 7546/3-1980螺钉和螺母用装配工具．十字螺丝刀尺寸

Prezentul standard stabileşte dimensiunile şurubelniţelor pentru locaşuri cruciforme, destinate montării şi demontării elementelor de fixare şi asamblare filetate la care capul este prevăzut cu locaş cruciform STAS 7545-78

DIN 5208-2013十字槽头镙钉用梅花改锥

The document specifies the requirements for dimensions and for other characteristics of double offset screwdrivers for cross point screws.

DIN 7427-2009螺钉和螺母装配工具.机用螺钉旋具插头用带内六角头的连接件.技术规范

This standard deals with square drive sockets and hexagon drive extensions for hexagon insert bits, machine operated; it includes the dimensions of the connecting parts. The hexagon drive ends are fixed in accordance with DIN 3126 and ISO 1173 respectively.

DIN 14800-9-2013消防和救援车辆用消防设备. 第9部分:金属加工和木工用工具箱

The document contains the composition of tools chests for metalworking and woodworking which are carried as fire brigade-technical equipment on fire brigade vehicles.

DIN 65253-2002带内细齿的螺钉用的L形扳手

The document applies to L-wrenches for screws with internal serrations. The dimensions of the screwdriver tip are in accordance with DIN 2325. These wrenches are used e.g. for cheese head screws with internal serration in accordance with LN 29950.