成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

电气和电子设备用机电开关检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 9536-2012电气和电子设备用机电开关.第1部分:总规范

本部分规定了电气和电子设备用的机电开关。 本部分适用的开关: a)借助导电部件(触头)的机械运动来断开、接通或转换电路连接的装置;b)大额定电压为480V;c)大额定电流为63A。本部分不适用于供信息处理系统使用的键盘和辅助键盘。本部分也可适用于机电琴键(按键)开关。开关系列将在对应本总规范的详细规范中描述。

GB/T 22663-2008工业机械电气设备.电磁兼容.机床抗扰度要求

本标准规定了用于工业环境或类似用途,线间额定电压不超过1000Va.c或者1500Vd.c的机床电磁兼容的抗扰度要求。本抗扰度标准也可用于评估在其他环境中使用的机床,这些环境(住宅、轻工业环境等)比工业环境要求的抗扰度水平低。本标准不适用于安装在特殊的电磁环境中的机床,例如:存在强电磁场(如在广播发射台附近),或在有电力网强脉冲环境(如发电站)的机床。在这些场合中使用的设备及系统,需采取相应的降低电磁影响的措施。本标准涉及电磁抗扰度的频率范围为0Hz至400GHz。其他频率不在标准考虑之列。

GB 23712-2009工业机械电气设备.电磁兼容.机床发射限值

本标准规定了用于工业环境或类似用途,线间额定电压不超过1000Va.c.或者1500Vd.c.的机床的电磁发射限值,但不包括电火花加工机床(EDM)。本标准涉及电磁发射的频率范围为9 kHz~400GHz。其他频率不在本标准考虑之列。

JB/T 13034-2017器具电子开关电气性能要求及试验方法

本标准规定了器具电子开关进行开关功能操作、发热、耐久性、电子开关的不正常工作和故障条件、控制特性、保护特性、开关电子器件寿命试验等电气性能试验的电气性能要求、试验方法和检验规则。本标准适用于器具开关中的电子开关(以下简称开关)进行电气性能设计、试验时的要求及试验方法,这些电子开关包括独立安装的、附装的、拼合的或者靠激发传感器(可在实体上或电气上与开关结合在一起,也可分开配置,还可能包含操动件或传感器与开关之间的信号传输,例如,电气的、光的、声的或温度的信号传输)操作的开关。在特殊环境下使用的器具电子开关电气性能要求及试验方法也可参照执行。

DL/T 593-2016高压开关设备和控制设备标准的共用技术要求

本标准适用于电压3.0kV及以上、频率为50Hz的电力系统中运行的户内和户外交流高压开关设备和控制设备。除非在特定类型开关设备和控制设备有关的产品标准中另有规定,本标准适用于所有的高压开关设备和控制设备。

EN 746-2-2010工业热加工工艺设备.燃烧和燃料储运系统安全要求

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (InThis standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers: fuel pipework downstream of and including the manual isolating valve; burner(s), burner system and ignition device; safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy. For thermal or catalytic post combustion and waste incineration,This European Standard applies only to auxiliary burners designed to start-up and/or support the process. The pressure hazard of the piping and components covered byThis standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE. NOTE EN 1539, Dryers and ovens, in which flammable substances are released-Safety requirementsThis European Standard is not applicable to combustion and fuel handling systems of welding and soldering machines; up-stream of the IThE manual isolating valve.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system. Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with inThis standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.

GSO IEC 61020-1-2014电气和电子设备用机电开关.第1部分:总规范

This generic specification relates to electromechanical switches intended for use in electrical and electronic appliances. Switches covered by this specification: a) are devices which open, close, or change the connection of a circuit by the mechanical motion of conducting parts (contacts); b) have a maximum rated voltage of 480 V; c) have a maximum rated current of 63 A. This generic specification does not include keyboards and keypads which are intended for use in information-handling systems. Electromechanical key switches may be included under the scope of this generic specification. Switch families shall be described in any detail specifications that will reference this generic specification.

NF C83-410-1-2019电气和电子设备的机电开关. 第1部分: 总规范

Domaine d'applicationLa présente partie de l'IEC 61020 spécifie la terminologie, les symboles, les méthodes d'essai et d'autres informations nécessaires pour assurer la cohérence des spécifications particulières applicables aux interrupteurs électromécaniques.Le présent document concerne les interrupteurs électromécaniques destinés à être utilisés dans les dispositifs électriques et électroniques. Les interrupteurs relevant du présent document:sont des dispositifs qui ouvrent, ferment ou commutent un circuit par le mouvement mécanique de leurs parties conductrices (contacts) ;ont une tension assignée maximale de 480 V;ont un courant assigné maximal de 63 A.Le présent document ne s'applique pas aux claviers prévus pour être utilisés dans les systèmes de traitement de l'information. Les interrupteurs électromécaniques à touche peuvent relever du domaine d'application du présent document.Les familles d'interrupteurs sont décrites dans des spécifications particulières faisant référence au présent document.Le présent document est une norme de qualité de fonctionnement destinée à décrire les méthodes d'appréciation afin de clarifier les capacités d'un interrupteur.Les exigences relatives à la sécurité des interrupteurs pour installations électriques fixes domestiques et analogues sont données dans l'IEC 60669 (toutes les parties) .Les exigences relatives à la sécurité des interrupteurs pour appareils sont données dans l'IEC 61058 (toutes les parties) .

DIN EN 746-2-2011工业热处理设备.第2部分:燃烧和燃料处理系统的安全要求;德文版本EN 746-2-2010

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (In this standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers:- fuel pipework downstream of and including the manual isolating valve;- burner(s), burner system and ignition device;- safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy.For thermal or catalytic post combustion and waste incineration, this European Standard applies only to auxiliary burners designed to start-up and/or support the process.The pressure hazard of piping and components covered by this standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system.Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with in this standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.

DIN EN 62047-5-2012半导体器件.微电机装置.第5部分:射频(RF)微电子机械系统(MEMS)开关(IEC 62047-5-2011).德文版本 EN 62047-5-2011

This standard describes terminology, definition, symbols, test methods that can be used to evaluate and determine the essential ratings and characteristic parameters of RF MEMS switches.

BS EN 746-2-2010工业热加工设备.燃烧和燃料处理系统的安全性要求

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners thatare part of Industrial Thermoprocessing Equipment. (In this standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion andfuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under theconditions foreseen by the manufacturer.This European Standard covers: fuel pipework downstream of and including the manual isolating valve; burner(s), burner system and ignition device; safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous,liquid and solid fuels or any combustion of them to release thermal energy.For thermal or catalytic post combustion and waste incineration, this European Standard applies only toauxiliary burners designed to start-up and/or support the process.The pressure hazard of the piping and components covered by this standard is within the limits of maximumpressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances fromthe products processed in the IThE.This European Standard is not applicable to combustion and fuel handling systems of welding and soldering machines; up-stream of the IThE manual isolating valve.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE controlpanel/protective system.Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with in thisstandard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which ismanufactured before the date of its publication as EN.

BS EN 50370-1-2005电磁兼容性(EMC).机床用产品系列标准.排放

This standard deals with the electromagnetic emission (radio frequency protection) of machine tools, excluding electro discharge machines (EDM), designed exclusively for industrial and similar purposes that use electricity, the rated voltage of the machine tool not exceeding 1 000 V AC or 1 500 V DC between lines.\nMachine tools may incorporate motors, heating elements or their combination, may contain electric or electronic circuitry, and may be powered by the mains, or any other electrical power source.\nThis standard does not cover fixed installations as defined in the Guide to the Application of Directive 89/336/EEC, published by the European Commission.\nEmission requirements in the frequency range 9 kHz to 400 GHz are covered. No measurements need to be performed at frequencies where no requirements are specified.

BS EN 50370-2-2003电磁兼容性(EMC).机床用产品系列标准.抗扰性

This standard deals with the electromagnetic immunity of machine tools designed exclusively for industrial and similar purposes that use electricity, the rated voltage of the machine tool not exceeding 1 000 V a.c. or 1 500 V d.c. between lines.\nMachine tools may incorporate motors, heating elements or their combination, may contain electric or electronic circuitry, and may be powered by the mains, or any other electrical power source.\nThis immunity standard may also be used for assessment of equipment used in other environments, which require less stringent immunity levels (residential, light industry...) than the industrial environment.\nThis standard is not intended for the EMC conformity assessment of modules to be placed on the market separately.\nThis standard is not intended for complying with Machinery Directive 98/37/EC. Hence safety considerations are not covered by this standard.\nThis standard does not cover fixed installations as defined in the Guide to the Application of Directive 89/336/EEC, published by the European Commission.\nThis standard does not apply to apparatus intended to be used in locations where special electromagnetic conditions prevail, such as the presence of high electromagnetic fields (e.g. in the vicinity of a broadcast transmitting station) or where high pulses occur on the power network (e.g. in a power generator station). In these instances special mitigation measures may have to be employed.\nImmunity requirements in the frequency range 0 Hz to 400 GHz are covered. No measurements need to be performed at frequencies where no requirements are specified.

上一篇氮化硅电热元件检测 下一篇智能电自动控制器检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通