铰接门和转门检测
GB/T 17454.3-2017机械安全 压敏保护装置 第3部分:压敏缓冲器、压敏板、压敏线及类似装置的设计和试验通则
GB/T 17454的本部分给出了GB/T 17454.1或GB/T 17454.2没有规定的带或不带外部复位装置的压敏保护装置的一般规则和要求。这些压敏保护装置中的大多数是针对特定应用定制生产的，不能以“标准现货供应”的形式提供。本部分也给出了以下压敏保护装置的具体要求：a) 压敏缓冲器；b) 压敏板；c) 压敏线(触发线)。本部分针对的是压敏装置的安全性和可靠性设计问题，而非具体应用中的适用性。本部分不适用于：——规定与任何具体应用相关的压敏保护装置尺寸；——用于正常运行的符合GB 5226.1的停止装置，包括紧急停机。如果压敏保护装置用于老年人、残疾人或儿童容易接近的地方，还需提出附加要求。
GB/T 20909-2017钢门窗
本标准规定了钢门窗的术语和定义、分类、规格和标记、一般要求、要求、试验方法、检验规则、标志、包装、运输及贮存。本标准适用于工业与民用建筑用钢窗和民用建筑用钢门。
JG/T 514-2017建筑用金属单元门
本标准规定了建筑用金属单元门的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于民用建筑用金属单元门。
NF E31-356-2008采暖锅炉.带强制通风燃烧器的采暖锅炉.标称热输出≤10MW和大工作温度为110℃
La présente Norme européenne spécifie les exigences et les méthodes d'essai pour la conception, la fabrication, la sécurité et l'utilisation rationnelle de l'énergie pour des chaudières standard et des chaudières à basse température (\"chaudière\" au sens de \"corps de chaudière\") en acier et en fonte, devant être équipées de brûleurs à air soufflé commercialisés séparément, conformes aux normes applicables aux brûleurs (pour les brûleurs automatiques à air soufflé pour combustibles gazeux, voir l'EN 676 et pour les brûleurs à fioul à pulvérisation, voir l'EN 267) jusqu'à une puissance utile nominale de 10 MW. Ces chaudières fonctionnent, selon les instructions du fabricant, soit en dépression (à tirage naturel), soit en pression (chaudières pressurisées) dans la chambre de combustion.La présente Norme européenne spécifie les exigences relatives aux chaudières dont la température normale de service est comprise entre 100 oC et 110 oC ; elle est structurée en \"deux volets\"Pour les chaudières dont la température de coupure du thermostat limiteur de sécurité ne dépasse pas 110 oC, la directive relative aux équipements sous pression (DEP) exige l'application des \"règles de l'art en usage\",Pour les chaudières dont la température de coupure du thermostat limiteur de sécurité est supérieure à 110 oC, la présente Norme européenne spécifie les exigences de la DEP indiquées dans l'Annexe ZB.
NF P26-332-2008建筑五金件.防火门/防烟门部件用电控开门系统.要求、试验方法、应用和保养
La présente Norme européenne spécifie les exigences, les méthodes d'essai et les critères de performances par rapport auxquels la compatibilité des composants et leurs performances peuvent être évaluées lorsqu'ils sont utilisés en combinaison pour former un système de retenue contrôlé électriquement. Elle spécifie également les exigences d'intégrité de ces systèmes de retenue lorsqu'ils sont connectés à des systèmes de détection et d'alarme incendie ou à d'autres systèmes, y compris l'échange de signaux, ainsi que les données techniques pour les interfaces.La présente Norme européenne donne les exigences pour la mise en couvre de systèmes de retenue contrôlés électriquement sur les portes coupe-feu/pare-fumée dans les bâtiments pour lesquels des portes à fermeture automatique sont exigées. Elle couvre la planification, la conception (voir Annexe A), l'installation (voir Annexe B), la mise en service, l'utilisation et la maintenance (voir Annexe E) de systèmes de retenue destinés à protéger la vie et/ou des biens. Ces derniers peuvent se présenter sous la forme de systèmes de retenue indépendants ou de composants de système de retenue contenus dans un boîtier séparé.Les systèmes de retenue contrôlés électriquement fabriqués, installés et entretenus conformément à la présente Norme européenne sont recommandés chaque fois qu'une fonction fiable de retenue et de fermeture automatique est requise pour un bloc-porte coupe-feu/pare-fumée en cas d'incendie.
DIN EN 948-1999铰接门或旋转门.耐静扭力测定
The document applies to all vertically hinged or pivoted doors. The document specifies the method to be used to determine the permanent deformation caused when static stress in torsion is applied to an open door leaf fixed in its own door frame as part of a doorset.
DIN EN 1634-2-2009门、百页窗和可开启窗户建筑五金组件和元件用防火和烟雾控制试验 第2部分:建筑五金组件用防火特性试验
This European Standard specifies a method for characterizing the influence on fire performance ofitems of building hardware for incorporation into hinged or pivoted vertically installed fire doorassemblies (having either one or two leaves) or vertically installed openable window assemblies, ofknown fire resistance of up to and including 240 minutes integrity (and where relevant insulation) inaccordance with EN 1634-1. It applies to the testing of building hardware for use on hinged andpivoted doors and openable windows which include framed glazed doors and windows, but not glassdoors. It does not include a test for durability or other performance characteristics, which should beevaluated according to the product standard for the item of building hardware or as given inEN 14600.The method is suitable for characterizing building hardware for use on non-metallic door or windowassemblies consisting of cellulosic materials or mineral boards faced with cellulosic materials, hung ineither cellulosic, mineral cored or metal frames: or conventional steel doors made from sheet steel,not more than 1,5 mm thick, hung in steel frames (steel doors include doors filled with mineral boardor mineral fibre cores but not steel clad timber/cellulosic doors). The size of these assemblies can beup to that given in the field of direct application for the door leaf construction concerned.This method is not directly appropriate for evaluating building hardware for use on glass or glazeddoors with decorative perimeter framing. The appropriateness of this method of test can beestablished by reference to the flow chart given in Annex A.This European Standard does not constitute a fire resistance test for a leaf, window, frame,intumescent seal, or anything other than the selected item of building hardware. The use of anyresulting field of direct application is restricted to leaf and frame constructions which have beensuccessfully tested to EN 1634-1. The method has been developed primarily to permit the evaluationof building hardware for hinged or pivoted door assemblies and openable windows, but the method isalso suitable for evaluating some items of building hardware, which are non-edge mounted, for usewith sliding doors and openable windows.
DIN EN 12896-1-2016公共运输.参照数据模型.第1部分:一般概念
The main objective of the present standard is to present the Public Transport Reference Data Model based on: - the Public Transport Reference Data Model published 2006 as EN 12896 and known as Transmodel V5.1, - the model for the Identification of Fixed Objects for Public transport, published 2009 as EN 28701 and known as IFOPT, incorporating the requirements of - EN 15531-1, EN 15531-2, EN 15531-3, CEN/TS 15531-4 and CEN/TS 15531-5: Service interface for real-time information relating to public transport operations (SIRI), - CEN/TS 16614-1 and CEN/TS 16614-2: Network and Timetable Exchange (NeTEx),
DIN EN 16122-2012住宅用和非住宅用储存设备.强度,耐久性和稳定性测定试验方法.德文版本EN 16122-2012
This European Standard specifies tests methods for the determination of strength, durability and stability for all types of domestic and non-domestic storage furniture including domestic kitchen furniture. It does not apply to office, industrial, catering equipment and retail storage, nor to industrial storage lockers.
DIN EN 16361-2016电动人行门.产品标准、性能特性.带动力操控装置的非摆动式行人门具的初始设计.德文版本EN 16361-2013+A1-2016
This European Standard specifies requirements and test/assessment/calculation methods for external and internal power operated pedestrian doorsets, other than swing type, initially designed for installation with power operation. Such doorset constructions may be operated electro-mechanically, electro-hydraulically or pneumatically. These doorsets include power operated pedestrian sliding doorsets, revolving doorsets, balanced (sliding/swing) doorsets and folding doorsets with one or more horizontally moving leaves. This European Standard applies to power operated pedestrian doorsets with flush or panelled leaves, complete with: integral fanlights, if any; side panels that are contained within a single frame for inclusion in a single aperture, if any. The intended uses of the products covered by this European Standard are: doorsets for external use in escape routes and other declared specific uses and/or uses subject to other specific requirements, in particular noise, energy, tightness and safety-in-use in construction works; doorsets for internal use in escape routes, communication and other declared specific uses and/or uses subject to other specific requirements, in particular noise, energy and safety-in-use in construction works. The products covered by this European Standard are not assessed for structural applications of the building. This European Standard does not cover operation in environments where the electromagnetic disturbances are outside the range of those specified in EN 61000-6-2. This European Standard does not apply to: external pedestrian doorsets according to EN 14351-1; internal pedestrian doorsets according to prEN 14351-2; fire resistance and/or smoke control characteristics according to EN 16034; lifts doorsets; vehicles doorsets; doorsets used in industrial processes; doorsets in partition walls; doorsets outside the reach of people (such as crane gantry fences); turnstiles; platform doorsets. This European Standard does not cover special
DIN EN ISO 13856-3-2013机械安全性.压敏保护装置.第3部分:压敏减震器、压敏平板和压敏带和类似装置设计和测试的通用原则(ISO 13856-3-2013).德文版本EN ISO 13856-3-2013
This part of ISO 13856 establishes general principles and specifies requirements for the design and testing of those pressure-sensitive protective devices, with or without an external reset facility, that are not specified in either ISO 13856-1 and ISO 13856-2, the majority of which are produced for specific applications and are not available as off-the-shelf items.
BS EN 179-2008建筑五金件.逃离线路用门拉手或推板控制的紧急出口装置.要求和试验方法
This European Standard specifies requirements for the manufacture, performance and testing ofemergency exit devices mechanically operated by either a lever handle or a push pad for the purposeof achieving a safe exit under an emergency situation on escape routes.The suitability of an emergency exit device for use on smoke/fire-resisting door assemblies isdetermined by fire performance tests conducted in addition to the performance tests required by thisEuropean Standard. Annex B indicates additional requirements for these products.This European Standard covers emergency exit devices, which are either manufactured and placedon the market in their entirety by one producer, or produced by more than one producer andsubsequently placed on the market as a kit in a single transaction.
BS EN 1125-2008建筑五金件.逃离线路用水平杆控制的应急出口装置.要求和试验方法
This European Standard specifies requirements for the manufacture, performance and testing of panic exitdevices mechanically operated by either a horizontal push-bar or a horizontal touch-bar, specificallydesigned for use in a panic situation on escape routes.The suitability of a panic exit device for use on fire/smoke resisting door assemblies is determined by fireperformance tests conducted in addition to the performance tests required by this European Standard.Annex B indicates additional requirements for these products.This European Standard covers panic exit devices which are either manufactured and placed on themarket in their entirety by one producer or produced by more than one producer and subsequently placedon the market as a kit in a single transaction.
BS EN 1634-2-2008建筑五金件的门,百叶窗和可开启窗户附件及组件.建筑五金组件耐火特性试验
This European Standard specifies a method for characterizing the influence on fire performance ofitems of building hardware for incorporation into hinged or pivoted vertically installed fire doorassemblies (having either one or two leaves) or vertically installed openable window assemblies, ofknown fire resistance of up to and including 240 minutes integrity (and where relevant insulation) inaccordance with EN 1634-1. It applies to the testing of building hardware for use on hinged andpivoted doors and openable windows which include framed glazed doors and windows, but not glassdoors. It does not include a test for durability or other performance characteristics, which should beevaluated according to the product standard for the item of building hardware or as given inEN 14600.The method is suitable for characterizing building hardware for use on non-metallic door or windowassemblies consisting of cellulosic materials or mineral boards faced with cellulosic materials, hung ineither cellulosic, mineral cored or metal frames: or conventional steel doors made from sheet steel,not more than 1,5 mm thick, hung in steel frames (steel doors include doors filled with mineral boardor mineral fibre cores but not steel clad timber/cellulosic doors). The size of these assemblies can beup to that given in the field of direct application for the door leaf construction concerned.This method is not directly appropriate for evaluating building hardware for use on glass or glazeddoors with decorative perimeter framing. The appropriateness of this method of test can beestablished by reference to the flow chart given in Annex A.This European Standard does not constitute a fire resistance test for a leaf, window, frame,intumescent seal, or anything other than the selected item of building hardware. The use of anyresulting field of direct application is restricted to leaf and frame constructions which have beensuccessfully tested to EN 1634-1. The method has been developed primarily to permit the evaluationof building hardware for hinged or pivoted door assemblies and openable windows, but the method isalso suitable for evaluating some items of building hardware, which are non-edge mounted, for usewith sliding doors and openable windows.
BS EN 12896-2006道路运输和交通远程信息管理.公共运输.参照数据模型
1.1 GeneralThe European reference data model for public transport is an offer to public transport companies and otherproviders of services related to the process of passenger transportation and information, to suppliers ofsoftware products supporting these processes, and to consultants and other experts acting in the field ofpublic transport in the widest sense.The reference data model can support the development of software applications, their interaction orcombination in an integrated information system, and the system‘s organisation and information managementwhich rules the utilisation of the existing telematics environment in a company (or group of companies)running computer applications supporting the different functional areas of public transport.Although primarily designed to document the information needs of a public transport company in a welldefined and structured way, the reference data model can also serve as a starting point and reference for thedefinition of a database schema. A database schema is needed for the physical implementation of datastorage systems to be used by applications directly, or for exchange of data between applications viainterfaces. Apart from that, such a database will often additionally be used as a source of information for thecompany management and/or as an information pool for all employees who may need access to theinformation basis of the company.1.2 OverviewThe data model describes elementary data needed fornetwork description; andversions management.that are used in several functional domains as basic concepts.The data model describes the information needs related to the following functional domains:tactical planning (vehicle scheduling, driver scheduling, rostering);personnel (driver) disposition;operations monitoring and control;passenger information;fare collection;management information and statistics.The standard takes into account the:multi-modal public transport operation;multiple operators environment.Licensed Copy: Wang Bin, na, Mon May 15 07:59:15 BST 2006, Uncontrolled Copy, (c) BSI
BS EN 14727-2005实验室设备.实验室用存储设备.要求和试验方法
This European Standard specifies requirements and test methods for storage units (see 3.1) used in laboratories.This European Standard specifies strength, durability and safety requirements to prevent serious injury through normal functional use, as well as misuse that might reasonably be expected to occur.Safety, depending on the structure of the building, is not included e.g. the strength of wall hanging cabinets includes only the cabinet and its parts. The wall and the fixing in the wall are not included.It should be understood that the tests do not ensure that structural failure will not eventually occur as a result of habitual misuse or after an excessively long period of service.Assessment of ageing, degradation and the heating effect of appliances are not included nor are ergonomic aspects or resistance to fire.
