卫生设备用花洒检测

卫生设备用花洒检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 9195-2011建筑卫生陶瓷分类及术语

本标准规定了建筑卫生陶瓷的分类、术语和定义。本标准适用于建筑卫生陶瓷的设计、生产、质量检验、贸易、科学研究、教学等领域。

GB/T 16662-2008建筑给水排水设备器材术语

本标准规定了建筑给水排水设备和器材，包括卫生器具，水嘴，加压、调节和贮存设备，加热贮热设备，地漏，检查井，建筑水处理设备，游泳池、游乐池设备，冷却设备，水景设备，雨水利用设备，管材，管件，阀门，计量、检测仪表等方面的专用术语。本标准适用于建筑给水排水设备和器材的专用术语。

GB/T 35577-2017建筑节水产品术语

本标准界定了建筑节水产品的通用术语及中水和雨水利用、建筑室内节水器具、建筑节水灌溉、建筑节水设备仪器仪表等术语。本标准适用于建筑节水相关产品的设计、研究、计量和统计等。

JC/T 2116-2012非陶瓷类卫生洁具

本标准规定了非陶瓷类卫生洁具的术语和定义、分类、技术要求、试验方法、检验规则、标志和标识、包装、运输和贮存。本标准适用于建筑物内和公共场所使用的非陶瓷类卫生洁具。

QB/T 2806-2017温控水嘴

本标准规定了温控水嘴的术语和定义、分类及标记、使用条件、材料、配套装置、要求、单柄三控温控水嘴、检测与试验方法、检验规则、标记、包装、运输和贮存。\r 本标准适用公称压力：普通水压不大于0.5MPa和高水压不大于2MPa，冷水温度4℃～29℃，热水温度45℃～85℃的条件下，安装在盥洗室(洗手间、浴室等)、厨房等卫生设施上，出水口温度自动受预选温度控制的冷热水混合水嘴。

QB/T 4050-2010淋浴器

本标准规定了淋浴器（淋浴柱）的产品分类、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于公称压力不大于1.0MPa，水介质温度不大于90℃条件下，安装在盥洗室(洗手间、浴室)、淋浴房等卫生设施上使用的淋浴器。 本标准不适用于自带加热装置的淋浴器。

JGJ 367-2015住宅室内装饰装修设计规范

本规范适用于住宅的室内装饰装修设计，不适用属于历史文物保护的住宅的室内装饰装修设计。

DB11/ 343-2006用水器具节水技术条件

本标准规定了用水器具，包括：水嘴、便器冲洗阀、便器、水箱配件、卫生设备用软管、内螺纹连\n接阀门、直角阀、淋浴器、淋浴用花洒在应用时应达到的满足节水要求的技术指标。

DIN EN 249-2010卫生用具.交联铸塑丙烯胶片制淋浴盆.试验方法和要求.德文版本EN 249-2010

This European standard specifies the requirements for shower trays for domestic purposes made from crosslinked cast acrylic sheet conforming with EN 263 with the aim of ensuring that the product, when installed in accordance with the manufacturer´s instructions, will provide satisfactory performance in use. This standard is applicable to all sizes and shapes of shower trays.

DIN EN 15200-2007卫生设备.多功能淋浴间

This standard specifies requirements and test methods for multifunction shower cabinets (subsequently referred to as unit(s)), used for domestic purposes.This standard does not apply to shower cabinets and shower enclosures.NOTE For the purposes of this standard the term \"domestic purposes\" includes use in hotels, accommodation forstudents and similar buildings, except when special provisions e. g. medical, are required.

BS 6100-7-2008建筑和土木工程.词汇.第7部分:设备

This part of BS 6100 defines terms for the systems, installations andequipment that:a) provide water, electricity, heat, warm air and gases;b) facilitate internal communication and transport, lighting and wasteremoval.This standard does not define terms outside the curtilage of premises,e.g. water supply and public health engineering, which are both coveredin BS 6100-6.

BS EN 1112-2008卫生开关龙头.1型和2型供水系统用卫生开关龙头的淋浴出口.通用技术规范

This European Standard specifies: the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which showeroutlets shall comply; the procedures for testing these characteristics.This European Standard applies to shower heads and hand showers of any material used for ablutionarypurposes and intended for equipping and supplementing sanitary tapware for baths and showers.This European Standard applies to shower heads and hand showers connected downstream of the obturatorof the tapware.Integral and remote spray attachments incorporated in tapware (e.g. sink and wash basin mixing valves) arenot covered by this standard.Details of pressures and temperatures are given in Table 1.Table 1 — Conditions of use/Classifications

BS EN 14506-2005防饮用水回流污染设备 自动排水道 C型、H系列

This document specifies:a) field of application;b) requirements for automatic diverters;c) dimensional and the physico-chemical properties and the properties of general hydraulic, mechanical andacoustic design of automatic diverters;d) test method and requirements for verifying these properties. For sanitary tapware (see Clause 2) with integrateddevices, the automatic diverter is only considered to be a backflow protection device if it haspassed the requirements of this document and additionally those of the applicable product standard forthe draw off tap or mixing valve;e) marking and presentation;f) acoustics.This document specifies the characteristics of automatic diverters suitable for use in drinking water systems atpressures up to 1 MPa (10 bar) and temperatures up to 65 °C and for 1 h at 90 °C. They are intended only forinstallation with no downstream closing device.This document is applicable to the product type indicated as follows:i) integrated in spout (outlet);ii) integrated in the mixing body;iii) non-integrated (part of a set) above the maximum water level.This document is not applicable to the product type non-integrated below the maximum water level.

BS EN 15200-2007卫生器具.多功能淋浴房

This standard specifies requirements and test methods for multifunction shower cabinets (subsequentlyreferred to as unit(s)), used for domestic purposes.This standard does not apply to shower cabinets and shower enclosures.NOTE For the purposes of this standard the term \"domestic purposes\" includes use in hotels, accommodation forstudents and similar buildings, except when special provisions e. g. medical, are required.