卫生设备用冷热混合水龙头检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 16662-2008建筑给水排水设备器材术语

本标准规定了建筑给水排水设备和器材，包括卫生器具，水嘴，加压、调节和贮存设备，加热贮热设备，地漏，检查井，建筑水处理设备，游泳池、游乐池设备，冷却设备，水景设备，雨水利用设备，管材，管件，阀门，计量、检测仪表等方面的专用术语。本标准适用于建筑给水排水设备和器材的专用术语。

GB 50096-2011住宅设计规范

为保障城镇居民的基本住房条件和功能质量，提高城镇住宅设计水平，使住宅设计满足安全、卫生、适用、经济等性能要求，制定本规范。本规范适用于城镇新建、改建和扩建住宅的建筑设计。住宅设计必须执行有关方针、政策和法规，遵守安全卫生、环境保护、节约用地、节约能源资源等有关规定。住宅设计除应符合本规范外，尚应符合现行有关标准的规定。

GB 50333-2013医院洁净手术部建筑技术规范

本规范适用于医院新建、改建、扩建的洁净手术部工程的设计、施工和验收。

GB 50555-2010民用建筑节水设计标准

本标准适用于新建、改建和扩建的居住小区、公共建筑区等民用建筑节水设计,亦适用于工业建筑生活给水的节水设计。

GB/T 50604-2010民用建筑太阳能热水系统评价标准

为贯彻实施能源节约、环境保护、建设节约型社会，推进在建筑上利用太阳能热水系统，规范民用建筑太阳能热水系统的评价，规定本标准。本标准适用于评价新建、改建和扩建民用建筑上使用的太阳能热水系统，以及在既有民用建筑上增设、改造的太阳能热水系统。评价太阳能热水系统应依据因地制宜的原则，结合建筑类型及其所在地域的太阳能资源、自然环境、经济发展水平、社会习俗等特点进行评价。民用建筑太阳能热水系统的评价，除应符合本标准外，尚应符合现行有关标准的规定。

GB 50687-2011食品工业洁净用房建筑技术规范

本规范适用食品加工和生产的新建、改建和扩建厂房中洁净用房的设计、施工、工程检测和工程验收。

GB 50881-2013疾病预防控制中心建筑技术规范

1.0.1 为适应我国疾病预防控制事业的发展，保证省、地(市)、县级疾病预防控制中心(以下简称 “疾控中心”)建筑在设计、施工和验收方面符合使用功能、安全、卫生、节能、环保等的基本要求，制定本规范。1.0.2 本规范适用于疾控中心建筑的新建、改建和扩建工程的建筑设计、施工和验收。本规范不适用于生物安全四级实验室。1.0.3 疾控中心的建设，必须坚持科学、合理、实用、规范的原则，应正确处理现状与发展、需要与可能的关系。应在满足基本功能、实现工艺设计要求的同时，体现标准化、智能化、人性化的特点。1.0.4 疾控中心的建设应符合现行有关疾病预防控制中心建设标准的规定。1.0.5 有生物安全要求的实验室，应符合现行标准《生物安全实验室建筑技术规范》GB 50346、《实验室生物安全通用要求》GB 19489的有关规定。动物实验室应符合现行标准《实验动物环境及设施》GB 14925及《实验动物设施建筑技术规范》GB 50447的有关规定。1.0.6 疾控中心建筑的设计、施工和验收除应执行本规范外，尚应符合现行有关标准的规定。

GB/T 51100-2015绿色商店建筑评价标准

本标准适用于绿色商店建筑的评价。

GB/T 51293-2018城市轨道交通给水排水系统技术标准

本标准适用于城市轨道交通工程给水排水系统的设计、施工及验收。

JGJ/T 229-2010民用建筑绿色设计规范

本标准适用于新建、改建和扩建民用建筑的绿色设计。

DIN EN 200-2008卫生设备用水龙头.1型和2型的供水系统用单一水龙头和组合水龙头.通用技术规范

This European Standard specifies: a) the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in: 1) a supply system of Type 1 (see Figure 1); 2) a supply system of Type 2 (see Figure 2); b) the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics of nominal size 1/2 and 3/4 single taps and combination taps; c) test methods to verify the characteristics. The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carried out during manufacture.) This European Standard applies to draw-off taps (single taps and combination taps) for use with sanitary appliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use with baths, wash basins, bidets, showers and sinks. Figure 1 shows a supply system of Type 1 with a pressure range of (0,05 to 1,0) Mpa [(0,5 to 10) bar]. Figure 2 shows a supply system of Type 2 with a pressure range of (0,01 to 1,0) Mpa [(0,1 to 10) bar]. This European Standard applies to sanitary draw-off taps of nominal size 1/2 and 3/4 (PN 10). The conditions of use and classifications are given in Table 1. The Table 2 gives the performance characteristics to be noted if the tap is used outside the recommended operating range.

DIN EN 817-2008卫生用水龙头.机械混合阀(PN 10).一般技术规范

This European Standard specifies:-- the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, endurance and acoustic characteristics with which mechanical mixing valves need to comply;-- test methods to verify the characteristics.The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carriedout during manufacture.This European Standard applies to PN 10 mechanical mixing valves for use with sanitary appliances installed inrooms used for bodily hygiene (cloakrooms, bathrooms, etc.) and in kitchens, i.e. for use with baths, wash basins,bidets, showers and sinks.The conditions of use and classifications are given in O.

DIN EN 1112-2008卫生设备用水龙头.1型和2型供水系统用卫生设备水龙头的淋浴喷头.一般技术规范

This European Standard specifies:-- the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which shower outlets shall comply;-- the procedures for testing these characteristics.This European Standard applies to shower heads and hand showers of any material used for ablutionarypurposes and intended for equipping and supplementing sanitary tapware for baths and showers.This European Standard applies to shower heads and hand showers connected downstream of the obturatorof the tapware.Integral and remote spray attachments incorporated in tapware (e.g. sink and wash basin mixing valves) arenot covered by this standard.Details of pressures and temperatures are given in Table 1.

DIN EN 15200-2007卫生设备.多功能淋浴间

This standard specifies requirements and test methods for multifunction shower cabinets (subsequently referred to as unit(s)), used for domestic purposes.This standard does not apply to shower cabinets and shower enclosures.NOTE For the purposes of this standard the term \"domestic purposes\" includes use in hotels, accommodation forstudents and similar buildings, except when special provisions e. g. medical, are required.

BS 5546-2010额定输入不超过70kW的家用燃气供热水装置的安装和维修规范

This British Standard specifies requirements for the selection,installation, inspection, commissioning and maintenance of gas‑firedwater-heating appliances, which have a rated heat input notexceeding 70 kW, based on net calorific value.It applies to water-heating appliances utilizing 1st, 2nd or 3rd familygases designed to operate in the condensing or non‑condensingmode for the supply of hot water for domestic purposes in domesticdwellings or domestic dwellings in commercial premises.This standard does not apply to:a) water-heating appliances with a rated input of over 70 kW;b) hot water supply systems in multiple dwellings supplied from acentral source.It does not cover the detailed design and installation of the whole hotwater distribution system, which was specified in BS 5449.This standard applies to water-heating appliances which carry aCE mark and also to previously used water-heating appliances whichdo not carry the CE mark (see 5.3.1).

BS 6100-7-2008建筑和土木工程.词汇.第7部分:设备

This part of BS 6100 defines terms for the systems, installations andequipment that:a) provide water, electricity, heat, warm air and gases;b) facilitate internal communication and transport, lighting and wasteremoval.This standard does not define terms outside the curtilage of premises,e.g. water supply and public health engineering, which are both coveredin BS 6100-6.

BS 6465-4-2010卫生器具.公共厕所业务守则条款

This part of BS 6465 gives recommendations on the location, numbers,siting, design and management of public toilets. It is applicable to theprovision of new facilities and to the retention and refurbishment ofexisting facilities.This standard is applicable to the following types of public toilet facilities:a) municipal public on-street toilets;b) off-street publicly available toilets (e.g. in shopping malls);c) automatic public conveniences (APCs);d) street urinals;e) facilities for disabled people, from the point of view of scale ofprovision and location;f) baby changing and ancillary toilet facilities.

BS EN 200-2008卫生用水龙头.1型和2型供水设备用单一水龙头和组合水龙头.通用技术规范

This European Standard specifies:a) the field of application for pillar taps, bib taps, single and multi-hole combination taps for use in:1) a supply system of Type 1 (see Figure 1);2) a supply system of Type 2 (see Figure 2);b) the dimensional, leaktightness, pressure resistance, hydraulic performance, mechanical strength, enduranceand acoustic characteristics of nominal size ½ and ¾ single taps and combination taps;c) test methods to verify the characteristics.The tests described in this European Standard are type tests (laboratory tests) and not quality control tests carriedout during manufacture.This European Standard applies to draw-off taps (single taps and combination taps) for use with sanitaryappliances installed in rooms used for bodily hygiene (cloakrooms, bathrooms etc.) and in kitchens, i.e. for use withbaths, wash basins, bidets, showers and sinks.Figure 1 shows a supply system of Type 1 with a pressure range of (0,05 to 1,0) Mpa [(0,5 to 10) bar].Figure 2 shows a supply system of Type 2 with a pressure range of (0,01 to 1,0) Mpa [(0,1 to 10) bar].This European Standard applies to sanitary draw-off taps of nominal size ½ and ¾ (PN 10).The conditions of use and classifications are given in Table 1. The Table 2 gives the performance characteristics tobe noted if the tap is used outside the recommended operating range.

BS EN 246-2003卫生设备用水龙头.流速调节器通用规范

This European Standard specifies:\n— the dimensional, mechanical, hydraulic and acoustic characteristics with which flow rate regulators should comply;\n— the procedures for testing these characteristics. This European Standard is applicable to:\n— flow rate regulators intended to be mounted on tapware used with sanitary appliances in toilets, washrooms and kitchens (single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);\n— flow rate regulators used under the following pressure and temperature conditions:\nFlow rate regulators can only be connected downstream of the obturator of the tap.

BS EN 806-2-2005人类消费用水的建筑物内部输水设备规范.设计

This document gives recommendations, and specifies requirements, on the design of potable water installations within buildings and for pipework outside buildings but within the premises (see EN 806-1) and applies to new installations, alterations and repairs.