成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

控制变压器和内置控制变压器的电源检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 5226.33-2017机械电气安全 机械电气设备 第33部分:半导体设备技术条件

GB/T 5226的本部分规定了半导体设备相关的制造、测量、组装和测试的电气、电子和可编程电子设备及系统的安全要求。本部分所论及的设备是从机械电气设备的电源引入处开始的(见5.1)。本部分适用的电气设备或电气设备部件,其标称电压不超过1 000 Va.c.或1 500 Vd.c.,额定频率不超过200 Hz。对于更高的电压或频率,可能需要特殊的要求。本部分包括针对电气安全隐患的防护措施和针对非电气安全隐患的电气联锁保护电路,但不涵盖由其他标准或法规规定的对人身安全保护的所有要求(如化学品危险、机械危险、辐射危害)。每种类型的机械适应其特定要求以提供足够的安全。下列半导体制造设备的电气装置应提供附加和特殊技术要求:——使用、加工或生产易爆材料;——在易燃易爆环境中使用;——当生产或使用某种材料时有特殊风险;——作为起重机械(包括在IEC 60204-32)。本部分不包括半导体设备的性能或功能特性规范。本部分不涉及对人类健康可能造成影响的源于半导体设备的排放(如电磁场,噪声)。本部分没有规定电磁兼容性(EMC)的要求。

GB 50303-2015建筑电气工程施工质量验收规范

本规范适用于电压等级为35kV及以下建筑电气安装工程的施工质量验收。

JT/T 1044-2016港口螺旋式连续卸船机

本标准规定了港口螺旋式连续卸船机的技术要求、试验方法、检验规则,以及标志、包装、运输和储存。本标准适用于港口干质散货连续卸船作业的卸船机,其他使用螺旋式取料及输送装置的干质散货处理机械亦可参照使用。

JTG/T F72-2011公路隧道交通工程与附属设施施工技术规范

1.0.1为指导公路隧道交通工程与附属设施施工及施工管理,保证公路隧道的安全及服务水平,进一步提高公路隧道交通工程与附属设施施工质量,制定本规范。1.0.2本规范适用于高速公路及一、二级公路的新建隧道,其他隧道可参照执行。1.0.3公路隧道交通工程与附属设施施工必须符合在安全生产方面的有关规定,采取完备的安全生产措施,保障人员、设施的安全。1.0.4公路隧道交通工程与附属设施施工不得危及、破坏隧道主体结构的安全。1.0.5公路隧道交通工程与附属设施施工必须符合在环境保护方面的有关规定。1.0.6公路隧道交通工程与附属设施施工应贯彻的技术经济政策,积极采用成熟可靠的新技术、新工艺、新材料和新设备。1.0.7公路隧道交通工程与附属设施施工除应符合本规范外,尚应符合现行有关标准的规定。

UL 1776-2002高压清洗机

These requirements cover inverters ,converters ,charge controllers ,and output controllers intended for use in stand-alone(not grid connected) or utility-interactive (grid-connected) power systems .Utility-interactive inverters and converters are intended to be installed in parallel with an electric supply system or an electric utility to supply common loads.

BS 6739-2009过程控制系统仪表的实施规范:安装设计和实施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.

BS EN 60076-4-2002电力变压器.电光脉冲和转换脉冲测试指南.电力变压器和电抗器

This part of IEC 60076 gives guidance and explanatory comments on the existing procedures forlightning and switching impulse testing of power transformers to supplement the requirements ofIEC 60076-3. It is also generally applicable to the testing of reactors (see IEC 60289),modifications to power transformer procedures being indicated where required.Information is given on waveshapes, test circuits including test connections, earthingpractices, failure detection methods, test procedures, measuring techniques and interpretationof results.Where applicable, the test techniques are as recommended in IEC 60060-1 and IEC 60060-2.

BS EN 60204-32-2008机械安全.机械的电气设备.起重机要求

This part of IEC 60204 applies to the application of electrical and electronic equipment andsystems to hoisting machines and related equipment.

BS EN 60204-33-2011机械安全.机械的电气设备.半导体制造设备要求

This part of IEC 60204 applies to electrical and electronic equipment associated withsemiconductor fabrication equipment for the manufacture, measurement, assembly, and test ofsemiconductors.NOTE 1 In this standard, the term electrical includes electrical, electronic, and programmable electronic matters(i.e. electrical equipment means electrical, electronic, and programmable electronic equipment).NOTE 2 In the context of this standard, the term person refers to any individual and includes those persons whoare assigned and instructed by the user or his agent(s) in the installation, use, and care of the fabricationequipment in question.The electrical equipment covered by this standard commences at the point of connection of thesupply to the electrical equipment (see 5.1), and includes proper instruction for its safeinstallation.NOTE 3 For the requirements for the electrical supply installation in buildings, see IEC 60364 series.This part is applicable to the electrical equipment or parts of the electrical equipment thatoperate with nominal supply voltages not exceeding 1 000 V for alternating current (a.c.) andnot exceeding 1 500 V for direct current (d.c.), and with nominal supply frequencies notexceeding 200 Hz. For higher voltages or frequencies, special requirements may be needed.NOTE 4 Electrical equipment within which derived voltages exceed these supply voltage limits is within the scopeof this standard.Included are requirements for protective measures against electrical safety hazards as well aselectrical interlock circuits that protect against non-electrical hazards. However, it does notcover all the requirements that are needed or required by other standards or regulations inorder to safeguard persons from hazards other than electrical hazards (e.g. chemical hazards,mechanical hazards, radiation hazards). Each type of machine has unique requirements to beaccommodated to provide adequate safety.Additional and special requirements can apply to the electrical equipment of fabricationequipment that:• use, process, or produce potentially explosive material;• are used in potentially explosive and/or flammable atmospheres;• have special risks when producing or using certain materials;• are hoisting machines (which are covered by IEC 60204-32).This standard does not include specifications for performance or functional characteristics ofthe fabrication equipment.This standard does not deal with the possible effects on human health that can result fromemissions (for example EMFs, noise) from the fabrication equipment.This standard does not specify requirements for electromagnetic compatibility (EMC).

上一篇轻型电动车辆中用的电池检测 下一篇电动自行车用镍蓄电池检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通