成分分析 · 材料检测 · 食品检测 · 环境检测

专业检测知识科普,帮您选对检测方案

咨询工程师

工业机器人轴承检测

发布时间:2024-06-21 作者:中析研究所 浏览:

GB/T 4754-2017国民经济行业分类

本标准规定了全社会经济活动的分类与代码。本标准适用于在统计、计划、财政、税收、工商等宏观管理中,对经济活动的分类,并用于信息处理和信息交换。

GB/T 16978-1997工业自动化 词汇

本标准定义了工业制造环境中有关的自动化名词术语。 注:本标准中的所有名词术语及其定义,均选自已经正式发布的ISO文件,这些文件均作为出处文件列出。下列每 一条定义后的数字|N|,即表示在附录A中所列的出处文件的序号。

GB/T 17780.1-2012纺织机械.安全要求.第1部分:通用要求

1.1 GB/T 17780的本部分针对纺织机械常见的危险及包含在GB/T 17780.2~17780.7中的有关零部件的危险规定了相应的安全要求。 1.2 本部分适用于纺织工业中有以下用途的机械和有关设备: ——纤维(短纤维和长丝)和其他原料制成纱线或非织造布(包括毡)的开、清、混、梳、精梳准备、纺纱和其他工序; ——纱线卷绕、并纱、捻线、变形工艺等以及机织和针织前的纱线准备工序; ——形成织物的机织、针织、花边织造以及其他类似工艺; ———带、绳、缆、索、麻线、网的编织等,搓绳机的卷取框除外; ——纤维、纱线、织物、编织带、绳索等的预处理,漂白、染色、印花和整理及出厂整装; ——成品的匹染; ——经编、纬编的整理,包括袜类,但不包括成品的缝合(即缝纫); ——机织、簇绒和其他生产地毯的工艺。 本部分适用于以上所列生产过程中的所有纺织机械和设备,包括能使单元机或联合机自动操作的设备,如纤维气流输送设备,但不包括机器间的运输装置。 GB/T 17780不涉及压力容器的具体要求。 1.3 本部分和其他部分提及的危险,仅限发生于机器的运输、装配、调整、使用、维护以及分解、拆卸和处理中。人工装卸也是机器正常操作的一部分。 1.4 GB/T 17780不适用于以下机械和相关设备: ——长丝和人造纤维的生产,包括形成初次成品(如长丝筒子、短纤维包); ——亚麻和类似原料的梳理; ——纺粘法和熔喷法非织造布的生产; ——服装、家用、产业用纺织品的缝制及非织造布的针刺和轧制; ——纺织成品的洗涤与干洗; ——纺织机械的维修(如梳针维护设备,印花机器组件的清洗); ——某些切割装置,如木料切割装置、激光切割、高压水枪、超声波装置。 注:附录E中的机械和设备用于纺织工业,但不包括在本部分范围内。 1.5 本部分及GB/T17780的其他部分不适用于在潜在爆炸性环境中使用的机械。 1.6 本部分及其他部分不适用于GB/T 17780.1~17780.7发布前制造的机器。

GB/T 25742.1-2010机器状态监测与诊断 数据处理、通信与表示 第1部分:一般指南

GB/T 25742的本部分规定了为机器状态监测与诊断的数据处理、通信与表示的软件规范制定的一般指南。

GB/T 31301.4-2015制鞋机械 安全要求 第4部分:鞋类成型机

GB/T 31301的本部分规定了鞋类成型机的结构、运输、安装、调试、设定、示教或过程转换、操作、清洗、维护、报废、拆解的相关安全要求。本部分包含操作者对机器的预期使用、及可预见的误用所产生的与鞋类成型机相关的全部重大危险、危险状态和危险事件(参见附录A)。本部分适用于制鞋工业内用于生产鞋及鞋配件的鞋类成型机器,包括:--连帮鞋成型机(见图1、图2和图3);--单底和鞋配件成型机(见图4~图10);--整鞋及靴成型机(见图11)。本部分也适用于上述机器用于生产鞋及其配件之外的其他产品,且生产这些产品不需要对机器进行模具之外的其他改动。本部分也适用于以下附加设备:喷雾装置、注射装置、浇注装置、喷嘴清洗器、拉料杆、模具清洗装置、活化装置、准备阶段和后处理机器人和设备(见图N.1)。本部分不适用于以下机器,除非其用于连帮鞋成型或反应成型:--使用固定注射装置和固定模具位置(夹紧装置)的成型机;--使用固定测量和混料装置及直线结构(模架)活动工作站的成型机。

GB/T 34884-2017滚动轴承 工业机器人谐波齿轮减速器用柔性轴承

本标准规定了工业机器人谐波齿轮减速器用柔性轴承(以下简称轴承)的代号方法、外形尺寸、技术要求、检测及试验方法、检验规则、标志和包装。本标准适用于轴承的生产、检验和验收。

GB/T 34897-2017滚动轴承 工业机器人RV减速器用精密轴承

本标准规定了工业机器人RV减速器用精密轴承(以下简称轴承)及轴承单元的分类、代号方法、结构型式、外形尺寸、技术要求、检测放法、检验规则、标志和防锈包装。本标准适用于轴承及轴承单元的生产、检验和验收。

GB/T 35127-2017机器人设计平台集成数据交换规范

本标准规定了机器人设计平台的数据集成框架、CAD系统与静力学分析系统、动力学仿真分析系统集成的流程和数据模型。本标准适用于机器人设计开发平台的数据集成框架和数据模型的研发过程。

JC/T 2260-2014墙材工业用码坯机器人

本标准规定了墙材工业用码坯机器人(以下简称码坯机器人)的术语和定义、型式、型号与基本参数、技术要求、试验条件和试验方法、检验规则以及标志、包装、运输和贮存。本标准主要适用于墙材工业烧结制品用码坯机器人。

JC/T 2500-2018陶瓷砖自动码包机

本标准规定了陶瓷砖自动码包机(以下简称码包机)的术语和定义、分类、型号和基本参数、要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于陶瓷砖自动码包机。

WJ 2675-2005兵器产品CAPP工艺设计用基本术语.机械类

本标准定义了兵器产品CAPP工艺设计机械类术语。本标准适用于机械类兵器产品使用CAPP系统进行的工艺设计。

YC/T 384.2-2018烟草企业安全生产标准化规范 第2部分:安全技术和现场规范

YC/T 284的本部分规定了烟草企业安全生产标准化的安全技术和现场规范要求,包括设备设施、作业活动、作业环境和现场运行的安全要求。本部分适用于省级烟草公司(局)、省级工业公司等省级公司、烟草加工和烟草商业生产经营单位。其中,烟草商业生产经营单位特指地市级烟草公司,烟草加工单位含烟叶复烤、卷烟制造、雪茄烟制造、再造烟叶生产的单位。烟草配套和多元化投资的其他生产经营单位,如醋酸纤维、烟草印刷等单位可参照执行。

UL 1740-2007机器人和自动设备

These requirements cover robots and robotic equipment rated 600 V or less and intended for installation in accordance with the National Electrical Code, ANSI/NFPA 70. Since end-use installation of a robot and robotic equipment may vary for each user application, guidelines for end-product installation may be evaluated to the applicable sections of ANSI/RIA R15.06, Standard for Industrial Robots and Robot Systems-Safety Requirements. Portions of the requirements in this Standard have been excerpted from the Robotic Industries Associations (RIA) Standard for Industrial Robots and Robot Systems - Safety Requirements, ANSI/RIA R15.06. These requirements cover robotic equipment and systems intended for indoor and outdoor use in applications such as parts assembly, parts transfer, automated material handling, inspection, loading, diecasting, deburring, welding, paint spraying, clinical/diagnostic systems, pharmaceutical applications, commercial food processing, automated vehicle refueling systems, library book handling/sorting, clean room applications, medical use for surgery, mobile robots, automated guided vehicles, automated storage/retrieval systems, and the like. Unique features or functions associated with the robotic application, not specifically addressed in this Standard, shall also be evaluated to other applicable Standards/requirements. These may include, but are not limited to, Electrical Equipment for Laboratory Use; Part 1: General Requirements, UL 3101-1; Medical and Dental Equipment, UL 544; Power Operated Pumps for Petroleum Product Dispensing Systems, UL 79. In addition to the requirements in this Standard, robots and robotic systems shall also comply with the applicable sections of the Electrical Standard for Industrial Machinery, ANSI/NFPA 79. Robots and robotic systems intended for use in hazardous locations, as defined by the National Electrical Code ANSI/NFPA 70, shall also comply with the requirements in Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II, and III, Division 1, Hazardous (Classified) Locations, UL 913. In the following text, a requirement that applies to one type of equipment, such as a controller or teach pendant, will be identified by a specific reference. In the absence of a specific reference or if the term robot or robotic equipment is employed, it is to be understood that the requirement applies to all types of equipment covered by this Standard.

NF G83-102-2008制鞋机械.靴模机械.安全要求

La présente Norme européenne s'applique aux machines de moulage pour chaussures utilisées dans l'industrie de la chaussure pour la production de chaussures et d'articles chaussants.Ces machines sont :- les machines de moulage direct des semelles ;- les machines de moulage d'éléments de chaussures et de semelles (voir Figures 4 à 10) ;- les machines pour moulage complet de chaussures et bottes.La présente Norme européenne s'applique également aux machines mentionnées lorsqu'elles sont utilisées pour des produits autres que les chaussures et articles chaussants, dans la mesure où ces produits ne nécessitent pas d'autre modification qu'un moule différent.La présente Norme européenne spécifie les prescriptions de sécurité relatives à la construction, au transport, à l'installation, à la mise au point, au réglage, à l'apprentissage ou au changement de procédé de fabrication, au fonctionnement, au nettoyage, à la maintenance, à la mise hors service, au démontage et, pour autant que cela concerne la sécurité, à la mise au rebut des machines mentionnées en 1.1.Elle traite de tous les phénomènes dangereux significatifs, situations et événements dangereux applicables aux machines de moulage pour chaussures, lorsqu'elles sont utilisées selon l'usage prévu et dans des conditions de mauvais usage raisonnablement prévisibles par le fabricant.

DIN 6892-2012无锥度连接的驱动式紧固件.直行键.计算和设计

This Standard establishes principles of design and calculation for parallel key connections whose parts are made of metallic materials. This Standard applies primarily to parallel key connections used in machines.

DIN 51233-2014材料试验机械.安全规范.总则

This document specifies safety requirements for materials testing machines, which help to attain the protective aimes for users, described in the relevant regulations and standards.

DIN EN 1845-2008制鞋机械.鞋模机械.安全要求

1.1 This European Standard applies to footwear moulding machines which are intended for use in the shoeindustry for the production of footwear and footwear components.These machines are:-- direct-on sole moulding machines (see Figures 1, 2 and 3);-- unit sole and footwear component moulding machines (see Figures 4 to 10);-- full shoe and boot moulding machines (see Figure 11).This European Standard applies also to the mentioned machines when used for other products than footwearand footwear components, as far as these products require no other changes than a different mould.1.2 This European Standard specifies safety requirements for construction, transport, installation,adjustment, setting, teaching or process change-over, operation, cleaning, maintenance, decommissioning,dismantling and, as far as safety is concerned, disposal for machines mentioned in 1.1.It deals with all significant hazards, hazardous situations and events relevant to footwear moulding machines,when they are used as intended and under conditions of misuse which are reasonably foreseeable by themanufacturer (see Clause 4).1.3 The following machines are excluded from the scope of this European Standard unless used for direct-on sole moulding or reaction moulding:-- moulding machines with static injection units and static mould stations (clamping units);-- moulding machines with static metering and mixing units and mobile stations with linear configuration (mould carriers).1.4 The European Standard does not deal with hazards created by the mixing and metering unit.NOTE For metering and mixing units, see EN 1612-1.The use of machines within the scope of this European Standard in industries other than those specified in 1.1may give rise to hazards not considered during its preparation.NOTE For this application see also EN 201 and prEN 1612-2.1.5 This European Standard also applies to the following additional equipment for material handling andoperation which are an integral part of the machine:-- spraying devices, injection units, casting units, nozzle cleaners, sprue pullers, mould front edge cleaners, activating devices, robots and equipment for preparatory and subsequent treatment (see Figure M.1).1.6 This European Standard assumes the machines:-- are operated by adequately trained persons;-- are used with adequate workplace lighting (see EN 12464-1).1.7 This document is not applicable to footwear moulding machines which are manufactured before thedate of publication of this European Standard by CEN.

DIN EN ISO 11111-1-2016纺织机械.安全要求.第1部分:通用要求(ISO 11111-1-2016).德文版本EN ISO 11111-1-2016

This part of ISO 11111 specifies safety requirements for frequently occurring hazards common to the types of textile machinery and the hazards of certain machine elements covered by ISO 11111-2 to ISO 11111-7. The standard series is complemented by the type C standards ISO 9902 (parts 1 to 7) with respect to noise emission measurement and ISO 23771 with respect to measures for the reduction of noise emissions. It is applicable to machinery plant and related equipment intended to be used in the textile industry for specified processes.

DIN EN ISO 16089-2016机床.安全性.固定式磨床(ISO 16089-2015).德文版本EN ISO 16089-2015

This EN ISO Standard specifies the requirements and/or measures to eliminate the hazards or reduce the risks in the following groups of stationary grinding machines which are designed primarily to shape metal by grinding: Group 1: Manually controlled grinding machines without power operated axes and without numerical control Group 2: Manually controlled grinding machines with power operated axes and limited numerically controlled capability, if applicable Group 3: Numerically controlled grinding machines NOTE 1 For detailed information on the groups of grinding machines, see the definitions in 3.1 and 3.4. NOTE 2 Requirements in this EN ISO Standard are, in general, applicable to all groups of grinding machines. If requirements are applicable to some special group(s) of grinding machines only, then the special group(s) of grinding machine(s) is/are specified. NOTE 3 Hazards arising from other metalworking processes (e. g. turning and laser processing) are covered by other Standards

上一篇直线轴承检测 下一篇推力关节轴承检测

相关阅读

了解更多检测知识

道桥材料检测

道桥材料检测覆盖水泥、沥青、集料、钢筋及结构混凝土等对象,通过取样规范、力学试验、化学分析与无损检测等手段,测定强度、变形、耐久等关键指标。本文按样品制备、检测方法、指标测定到判定标准的步骤展开,说明各环节操作要点,并给出第三方检测机构的选择要素,可用于工程质量控制与验收参考。

2026-11-13 | [其他]

洗衣凝珠检测

洗衣凝珠检测围绕成分、性能与安全三大维度展开,涵盖取样规范、HPLC法测定活性物含量、表面活性剂鉴定与酶活分光光度法测定、去污力与溶解性能试验、微生物限量与重金属指标判定。本文按流程分述各检测方法与操作要点,供质量控制与委托检测参考。

2026-11-09 | [其他]

绿色食品检测

绿色食品检测覆盖农药残留、重金属、微生物限量及理化品质等维度。本文按样品制备、GC-MS农残测定、ICP-MS重金属测定、平板计数法微生物检验的顺序说明操作要点,并阐述灵敏度、回收率等方法验证指标与判定标准,适合标志申报与质量控制场景参考。

2026-11-07 | [其他]

吐鲁番葡萄检测

吐鲁番葡萄检测围绕样品采集制备、农药残留GC-MS与HPLC分析、糖度及营养成分分光光度测定、重金属与微生物联检等环节展开。检测依据食品安全国家标准中的限量要求判定,报告可用于收购分级、市场准入及地理标志产品核查,检测流程规范、结果可追溯。

2026-10-31 | [其他]

食品过敏原检测

食品过敏原检测覆盖样本制备、ELISA蛋白筛查、PCR基因成分鉴定及LC-MS/MS质谱确证等环节。检测针对乳、蛋、花生、坚果、麸质等常见致敏成分,以检出限、特异性、回收率等指标评价方法性能,判定结果用于交叉污染控制、标签标示与进出口合规管理。

2026-10-29 | [其他]

二硫化钼检测

二硫化钼检测围绕物相结构、微观形貌、粒度分布与化学纯度展开,常用X射线衍射鉴别2H与1T晶型及杂相,拉曼光谱判断层数与缺陷状态,扫描电镜观察颗粒形貌,激光粒度法测定粒径分布,ICP光谱定量杂质元素。本文按制样、表征、指标判定的流程介绍各方法操作要点与适用场景。

2026-10-29 | [其他]

我们的优势

选择中析研究所的八大理由

资质齐全

旗下实验室依法依规开展检测,报告科学公正,获监管与客户广泛认可。

设备先进

上千台精密仪器定期检定校准,量值溯源体系完善。

专家团队

多领域技术专家,十年以上经验,破解各类疑难检测。

标准覆盖广

覆盖GB、行标及ISO、ASTM等国际标准,可定制方案。

周期短

常规项目7-10个工作日出报告,流程标准高效。

加急服务

支持加急检测通道,助力客户快速完成质量把关。

一对一服务

工程师全程对接,需求沟通到报告解读全流程陪伴。

数据保密

严格保密制度,客户样品与检测数据安全无忧。

旗下实验室资质

我司旗下实验室具备CMA资质认定及CNAS认可,具体项目是否在资质认定/实验室认可范围内请与工程师确认。

CMA检验检测机构资质认定证书

CMA检验检测机构资质认定证书

CNAS实验室认可证书

CNAS实验室认可证书

ISO管理体系认证证书

ISO管理体系认证证书

高新技术企业证书

高新技术企业证书

中国分析测试协会会员单位

中国分析测试协会会员单位

中国质量协会会员证书

中国质量协会会员证书

AAA级信用企业证书

AAA级信用企业

绿色低碳诚信示范创建企业证书

绿色低碳诚信示范创建企业

仪器设备

1000余台精密设备 · 点击查看原图

气相色谱-质谱联用仪

气相色谱-质谱联用仪 GC-MS

复杂有机组分的定性鉴定与未知物剖析利器。

高效液相色谱仪

高效液相色谱仪 HPLC

食品添加剂、药品成分等热敏物质的精准检测。

电感耦合等离子体发射光谱仪

电感耦合等离子体发射光谱仪 ICP-OES

一次进样同时读出数十种金属元素含量。

傅里叶变换红外光谱仪

傅里叶变换红外光谱仪 FTIR

通过特征吸收峰快速判断材料种类与分子结构。

X射线荧光光谱仪

X射线荧光光谱仪 XRF

几分钟完成元素快检,且不损伤样品。

扫描电子显微镜

扫描电子显微镜 SEM

放大数十万倍观察表面微观结构,锁定失效根源。

液相色谱-质谱联用仪

液相色谱-质谱联用仪 LC-MS

农兽药残留等痕量物质的高灵敏确证检测。

气相色谱仪

气相色谱仪 GC

溶剂残留、香气成分等挥发性物质的专业检测。

在线工程师 一对一服务

检测需求不知从何入手?立即联系在线工程师,一对一解答检测疑问,免费获取检测方案与报价。

VR实验室720°全景 NEW · 全新上线 VR实验室上线啦! 720°全景实景观览 · 足不出户走进实验室 立即体验 检测咨询 · 立即在线沟通