锥形衬套检测

GB/T 281-2013滚动轴承 调心球轴承 外形尺寸

本标准规定了符合GB/T 273.3-1999的调心球轴承及带紧定套的调心球轴承(以下简称轴承)的外形尺寸。本标准适用于调心球轴承的设计和选型。

GB/T 288-2013滚动轴承 调心滚子轴承 外形尺寸

本标准规定了符合GB/T 273.3-1999的调心滚子轴承和带紧定套的调心滚子轴承(以下简称轴承)的外形尺寸。本标准适用于调心滚子轴承的设计和选型。

GB/T 9160.1-2017滚动轴承 附件 第1部分:紧定套和退卸衬套

GB/T 9160的本部分规定了锥度为1∶12和锥度为1∶30的紧定套、紧定衬套和退卸衬套的代号方法、尺寸、技术要求、检测方法、检验规则以及标志和防锈包装等。本部分适用于尺寸系列符合GB/T 273.3的滚动轴承用紧定套和退卸衬套的生产、检验和验收。

GB/T 35147-2017石油天然气工业 机械动力传输挠性联轴器 一般用途

本标准规定了在石油、石化和天然气工业中两个机器旋转轴之间传输动力联轴器的一般用途。该应用通常指联轴器在不超过4 000 r/min的情况下传输动力,两机器(刚性轴机器)之间的一阶横向振动临界转速高于运转速席范围。若达成一致,可适用于以上限制之外的应用。本标准涵盖联轴器的设计、材料、检验、试验,以及连接传动轴的方法(包括锥形套筒和其他专用装置。本标准适用于联接设备上用来调节横向偏移、角偏差和轴向位移,而不需施加额外机械载荷的联轴器。本标准涵盖的联轴器包括齿式联轴器(及其他机械接触类型的联轴器)、金属挠性元件联轴器和各种弹性元件联轴器。以上联轴器可以是整体金属制件或可以包含非金属材料部件,如复合材料部件。本标准不适用于特殊类型的联轴器,如离合式、液压式、涡流式、固定式和径向花键式联轴器。本标准未定义联轴器特殊应用场合下的选型。

GB 51011-2014煤矿选煤设备安装工程施工与验收规范

本规范适用于选煤设备安装工程的施工与验收。

YS/T 5421-2014有色金属矿山设备安装工程质量检验评定标准

本标准适用于有色金属矿山设备安装工程质量的检验评定。

JB/T 11008-2010高速部分流泵

本标准规定了石油、重化学和天然气工业用高速部分流泵(以下简称泵)的型式与基本参数、设计、检查和试验、交付准备、标志、包装、运输和贮存等。本标准适用于采用齿轮箱增速和电动机变频增速的高速部分流泵。

JB/T 12264-2015滚动轴承和关节轴承 电子媒体查询结构 用特征词汇标识的特征和性能指标

本标准建立了一个用于识别滚动轴承、关节轴承、轴承座及附件的查询结构和特征词汇，主要应用于电子媒体，如互联网。本标准不包括查询程序。

DIN EN 14986-2017工作在潜在易爆环境中电扇的设计;德文版本EN 14986-2017

1.1 This European Standard specifies the constructional requirements for fans constructed to Group II G (of explosion groups IIA, IIB and hydrogen) categories 1, 2 and 3, and Group II D categories 2 and 3, intended for use in explosive atmospheres. NOTE Operation conditions for the different categories of fans used in this European Standard are defined in Clause 4. 1.2 This European Standard does not apply to group I fans (fans for mining), cooling fans or impellers on rotating electrical machines, cooling fans or impellers on internal combustion engines. NOTE 1 Requirements for group I fans are given in EN 1710. NOTE 2 The requirements for electrical parts are covered by references to electrical equipment standards. 1.3 This European Standard specifies requirements for design, construction, testing and marking of complete fan units intended for use in potentially explosive atmospheres in air containing gas, vapour, mist and/or dusts. Such atmospheres may exist inside (the conveyed fluid), outside, or inside and outside of the fan. 1.4 This European Standard is applicable to fans working in the range of ambient atmospheres having absolute pressures ranging from 0,8 bar to 1,1 bar, temperatures ranging from -20 °C to +60 °C, maximum volume fraction of 21 % oxygen content and an aerodynamic energy increase of less than 25 kJ/kg.

DIN EN ISO 13709-2010石油、石化和天然气工业用离心泵

This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services.This International Standard is applicable to overhung pumps, between-bearings pumps and vertically suspended pumps (see Table 1). Clause 9 provides requirements applicable to specific types of pump. All other clauses of this International Standard are applicable to all pump types. Illustrations are provided of the various specific pump types and the designations assigned to each specific type.

DIN EN ISO 13710-2005石油、石油化学和天然气工业.往复式变容真空泵

This Europaen Standard contains requirements on positive reciprocating displacement pumps.

DIN EN ISO 14691-2009石油、石化和天然气工业.机械动力传输用软管.通用设备

This International Standard specifies the requirements for couplings for the transmission of power between therotating shafts of two machines for general-purpose applications in the petroleum, petrochemical and naturalgas industries. Such applications typically require couplings to transmit power at speeds not exceeding4 000 r/min, between machines in which the first lateral critical speed is above the running speed range(stiff-shaft machines). It can, by agreement, be used for applications outside these limits.NOTE 1 Recommendations are included in the Introduction as to when the use of ISO 10441 should be considered.This International Standard is applicable to couplings designed to accommodate parallel (or lateral) offset,angular misalignment and axial displacement of the shafts without imposing excessive mechanical loading onthe coupled machines. Couplings covered by this International Standard include gear (and other mechanicalcontact types), metallic flexible-element and various elastomeric types. Such couplings can be of all metalconstruction or can include components of non-metallic materials, such as composites.This International Standard covers design, materials of construction, inspection and testing of couplings andmethods of attachment of the coupling to the shafts (including tapered sleeve and other proprietary devices).This International Standard does not apply to special types of couplings, such as clutch, hydraulic, eddy-current, rigid and radial-spline types.This International Standard does not define criteria for the selection of coupling types for specific applications.NOTE 2 In many cases, couplings covered by this Intemational Standard are manufacturers' catalogue items.