焊接未退火奥氏体不锈钢管型制品检测

焊接未退火奥氏体不锈钢管型制品检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 21412.5-2017石油天然气工业 水下生产系统的设计和操作 第5部分:水下脐带缆

GB/T 21412的本部分规定了脐带缆及相关附属设备的设计、材料选择、制造、设计验证、试验、安装和操作要求，并给出了推荐作法，用于石油天然气工业。附属设备不包括上部组块硬件装置，这些硬件是指那些在上部组块悬挂终端之上，不与脐带缆永久连接的设备。本部分适用于单独的部件，如电缆、光纤、热塑性软管或金属管构成的脐带缆，或它们组合成的脐带缆。本部分适用于静态或动态运行的脐带缆，其路径可为水上-水上，水上-水下和水下-水下。本部分不适用于相关部件接头，除非这些接头影响到脐带缆或其附属设备的性能。本部分仅适用于以下尺寸的金属管：壁厚t＜6 mm，内径ID＜50.8 mm(2 in)。大于这些尺寸的产品应视为管/管道并且按照公认的管线/管道标准进行设计和制造。本部分不适用于额定压力小于7 MPa(1 015 psi)的金属管或软管。本部分不适用于额定电压高于标准额定电压U<下标0>/U(U<下标m>)＝3.6/6(7.2)kV rms的电缆，其中U<下标0>、U与U<下标m>由IEC 60502-1与IEC 60502-2定义。

GB 50235-2010工业金属管道工程施工规范

本规范适用于设计压力不大于42MPa，设计温度不超过材料允许使用温度的工业金属管道工程的施工。本规范不适用于下列工业金属管道的施工：1 石油、天然气、地热等勘探和采掘装置的管道；2 长输管道；3 核能装置的专用管道；4 海上设施和矿井的管道；5 采暖通风与空气调节的管道及非圆形截面的管道。

GB/T 51012-2014铀浓缩工厂工艺气体管道工程施工及验收规范

本规范适用于设计压力1Pa~0. 8MPa(G)、设计温度-80℃~100℃的铀浓缩工艺气体管道。

GB 51205-2016精对苯二甲酸工厂设计规范

本规范适用于精对苯二甲酸工厂生产装置和辅助生产设施的新建、扩建和改建工程的设计，不包括为精对苯二甲酸工厂服务的公用工程设施和办公设施。

SY/T 0608-2014大型焊接低压储罐的设计与建造

本标准适用于具有单一垂直回转轴，用于储存石油中间产品(气体或蒸气)、成品以及其他类似液体的大型钢制焊接低压地上储罐的设计与建造。本标准适用于设计压力(表压)小于0.1MPa (15lb/in<上标2>)，金属温度不高于120℃ (250℉)的储罐。本标准的基本规定适用于低日平均环境温度为-45℃ (-50℉)以上的建罐地区。附录S中的低压不锈钢储罐不受环境温度的限制。附录R适用于温度范围在-51℃～4. 5℃ (-60℉～+ 40℉)的冷藏产品的低压储罐。附录Q适用于温度不低于-198℃(-325℉)的液化烃气的低压储罐。本标准的规定可适用于：a)盛装或储存液面以上存在气相空间的液体储罐。b)单独盛装或储存气体或蒸气的储罐，但不适用于悬挂式的气体储罐。与按本标准建造储罐的罐体相连接的内部和外部接管，超出以下范围的不在本标准规定范围内：a)螺栓连接法兰的第一个法兰密封面。b)罐体外侧螺纹连接的第一个螺纹接头。c)焊接连接的第一道环向接头。

UL 399-2008饮用水冷却器

1.1 These requirements cover self-contained drinking-water coolers which employ hermetic refrigerantmotor-compressors and which are designed for connection to alternating-current circuits rated not greaterthan 600 volts in accordance with the National Electrical Code, NFPA 70. The requirements also apply towater coolers which supply both hot and cold water.1.2 These requirements do not include additional requirements applicable to equipment designed for usein hazardous locations as defined in the National Electrical Code, NFPA 70.1.3 A product that contains features, characteristics, components, materials, or systems new or differentfrom those covered by the requirements in this standard, and that involves a risk of fire, electric shock, orinjury to persons shall be evaluated using the appropriate additional component and end-productrequirements as determined necessary to maintain the acceptable level of safety as originally anticipatedby the intent of this standard. A product whose features, characteristics, components, materials, orsystems conflict with specific requirements or provisions of this standard cannot be judged to comply withthis standard. Where considered appropriate, revision of requirements shall be proposed and adopted inconformance with the methods employed for development, revision, and implementation of this standard.

EN 10297-1-2003机械和一般工程用途的无缝圆形钢管.交货技术条件.第1部分:非合金钢管和合金钢管

This part of EN 10297 specifies the technical delivery conditions for seamless circular tubes made of non-alloy andalloy steels for mechanical and general engineering purposes

EN ISO 13628-5-2009石油和天然气工业.水下采油系统的设计和操作.第5部分:海底缆线

This International Standard specifies the general, and some of the special, requirements on materials used for the construction of equipment used in gas welding, cutting and allied processes.

DIN EN 10253-3-2009对焊管配件.第3部分:无特殊检验要求的锻制奥氏体和奥氏体-铁素体(二相)不锈钢

1.1 This part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austeniticand austenitic-ferritic (duplex) stainless steel without specific inspection requirements.It specifies:-- steel grades;-- mechanical properties;-- dimensions and tolerances;-- requirements for inspection and testing;-- inspection documents;-- marking;-- handling and packaging.1.2 Limitation of useThe allowed pressures and temperatures are the responsibility of the customer according to the state of theart and in application of the safety coefficients in the application regulations, codes and standards.In common, joint coefficient is used in the calculation of the thicknesses of components which include one orseveral butt welds, other than circumferential:-- for equipment subject to random non-destructive testing: 0,85;-- for equipment not subject to non-destructive testing other than visual inspection: 0,7.1.3 Unless otherwise specified in this part of EN 10253 the general technical delivery requirements inEN 100021 apply.

DIN EN 10253-4-2008对焊管配件.第4部分:具有特殊检验要求的锻制奥氏体和铁素体－奥氏体(二相)不锈钢

1.1 This European Standard specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at Iow temperature or at elevated temperatures. It specifies: -- the type of fittings; -- type A (see 7.2) -- type B (see 7.3) -- the steel grades; -- the mechanical properties; -- the dimensions and tolerances; -- the requirements for inspection and testing; -- the inspection documents; -- the marking; -- the handling and packaging. NOTE In the case of a harmonised supporting standard for materials, presumption of conformity to the Essential Requirement(s) (ESRs) is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently the technical data stated in the material standard should be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive (PED) are satisfied. 1.2 Unless otherwise specified in this European Standard the general technical delivery requirements in EN 10021 apply.

DIN EN ISO 13628-5-2010石油和天然气工业.水下采油系统的设计和操作.第5部分:海底缆线

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surface-subsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.

DIN EN ISO 13628-15-2012石油和天然气工业.海底生产系统的设计与操作.第15部分:海底结构和歧管(ISO 13628-15-2011).英文版 EN ISO 13628-15-2011

This part of ISO 13628 addresses specific requirements and recommendations for subsea structures and manifolds, within the frameworks set forth by recognized and accepted industry specifications and standards. As such, it does not supersede or eliminate any requirement imposed by any other industry specification. This part of ISO 13628 covers subsea manifolds and templates utilized for pressure control in both subsea production of oil and gas, and subsea injection services.

DIN EN ISO 13631-2003石油和天然气工业.封装往复式空气压缩机

The document gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of package skid-mounted, reciprocating, separable or integral compressors with lubricated cylinders and their prime movers, for use in the petroleum and natural gas industries for the compression of hydrocarbon gas.#,,#

DIN EN ISO 13706-2012石油、石化和天然气工业.风冷热交换器

This International Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum, petrochemical and natural gas industries. This International Standard is applicable to air-cooled heat exchangers with horizontal bundles, but the basic concepts can also be applied to other configurations.

BS 6180-2011建筑物内及附近用防护栅栏.实施规程

This British Standard gives recommendations and guidance for the design and construction of temporary and permanent barriers to be provided in and about buildings and places of assembly, such barriers being positioned and designed to protect persons from various hazards and to restrict or control the movement of persons or vehicles.This British Standard applies to:a) barriers that indicate routes;b) barriers capable of stopping or diverting moving vehicles within areas where vehicle speed is restricted to a maximum of 16 km/h (4.44 m/s, 10 mile/h);c) walls, glazing and other elements of buildings or structures where such elements act as protective barriers;d) areas other than spectator areas of sports halls and buildings used for spectator sports.This British Standard does not apply to:1) barriers for resisting impact from vehicles travelling at speeds greater than 16 km/h, e.g. bridge parapets beyond the curtilage of a building, or highway safety barriers (see BS 6779);2) barriers used in building operations and works of engineering construction;3) safety barriers, with or without opening gate features, for the protection of children up to 24 months, where the safety requirement is covered by a specific safety standard, e.g. BS EN 1930;4) permanent means of access to machinery (see BS EN ISO 14122, all parts);5) barriers used in spectator areas of sports halls, and buildings used for spectator sports (see BS EN 13200, all parts).

BS 7993-2011316不锈钢系统用双套管连接器和组合管道.规范和试验方法

This British Standard specifies the characteristics of, and performancerequirements for, the tube connector (compression) end(s) of twin ferruleconnectors made of 316 stainless steel. It also specifies requirementsfor 316 stainless steel tubes.The twin ferrule connectors in this standard are suitable for use with annealedstainless steel tubes with outside diameters from 2 mm to 38 mm and1/16 in to 2 in.This British Standard is applicable to twin ferrule connectors that are intendedfor the connection of plain end tubes to other tubes and to ports in accordancewith BS EN ISO 6149-1, BS EN ISO 1179 and BS EN ISO 9974-1, and other portsagreed between the purchaser and manufacturer. It provides external envelope,tube-end-to-tube-end and tube-end-to-port dimensions that facilitate designingsystems that use twin ferrule connectors.NOTE These twin ferrule connectors can also be used with other austenitic stainlesssteel tubes, typically 304, 316L, 321, etc.

BS EN 10253-3-2008对焊管接头.无特殊检验要求的锻制奥氏体和奥氏体-铁素体(二相)不锈钢

1.1 This part of EN 10253 specifies the technical delivery requirements for seamless and welded buttweldingfittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austeniticand austenitic–ferritic (duplex) stainless steel without specific inspection requirements.It specifies: steel grades; mechanical properties; dimensions and tolerances; requirements for inspection and testing; inspection documents; marking; handling and packaging.1.2 Limitation of useThe allowed pressures and temperatures are the responsibility of the customer according to the state of theart and in application of the safety coefficients in the application regulations, codes and standards.In common, joint coefficient is used in the calculation of the thicknesses of components which include one orseveral butt welds, other than circumferential: for equipment subject to random non-destructive testing: 0,85; for equipment not subject to non-destructive testing other than visual inspection: 0,7.1.3 Unless otherwise specified in this part of EN 10253 the general technical delivery requirements inEN 100021 apply.

BS EN 10253-4-2008对焊管道接头.具有特殊检验要求的锻制奥氏体和铁素体－奥氏体(二相)不锈钢

1.1 This European Standard specifies the technical delivery requirements for seamless and welded butt-weldingfittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic andaustenitic-ferritic (duplex) stainless steel which are intended for pressure and corrosion resisting purposes at roomtemperature, at low temperature or at elevated temperatures.It specifies: the type of fittings; type A (see 7.2) type B (see 7.3) the steel grades; the mechanical properties; the dimensions and tolerances; the requirements for inspection and testing; the inspection documents; the marking; the handling and packaging.NOTE In the case of a harmonised supporting standard for materials, presumption of conformity to the EssentialRequirement(s) (ESRs) is limited to technical data of materials in the standard and does not presume adequacy of the materialto a specific item of equipment. Consequently the technical data stated in the material standard should be assessed against thedesign requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive (PED) aresatisfied.1.2 Unless otherwise specified in this European Standard the general technical delivery requirements inEN 10021 apply.