圆锯床检测

GB/T 6477-2008金属切削机床.术语

本标准规定了金属切削机床的一般术语、车床、铣床、钻床、镗床、磨床、齿轮加工机床、螺纹加工机床、刨床和插床、拉床、锯床、组合机床及组合机床自动线、刻线机、管子加工机床、机床附件，运动、参数、零部件和加工方法的术语及其定义。本标准适用于一般用途的金属切削机床（以下简称机床）。

GB 16454-2008金属锯床.安全防护技术条件

本标准针对金属锯床存在的主要危险，规定了消除危险和减少风险的基本安全要求和/或措施。本标准适用于一般用途的卧式带锯床、立式带锯床、圆锯床和卧式弓锯床（以下简称锯床）。

HB/Z 99.4-1987飞机制造工艺工作导则.工艺文件编制工作条例

本条例规定了飞机工厂主要工艺文件的种类、编制要求、出版及更改方法。用于指导各飞机工厂工艺文件编制工作。　　本条例适用于各种新飞机（包括自行设计、实物测绘、仿制设计和改型设计的飞机）在研制、试制和批生产阶段的工艺文件编制，而且主要适用于钣金冲压、机械加工、部件装配、总装试飞等各的工艺文件编制合作生产及研究机的工艺文件编制可参照实施。

JB/T 3364.1-2011圆锯床.第1部分：型式与参数

JB/T 3364的本部分规定了圆锯床的系列构成、用途及性能、参数。本部分适用于新设计的冷锯金属的卧式圆锯床、摆式圆锯床和立式圆锯床。

JB/T 3364.2-2011圆锯床.第2部分：精度检验

JB/T 3364的本部分规定了圆锯床的几何精度和工作精度的要求及检验方法。本部分适用于大圆锯片直径315 mm～2000 mm的卧式圆锯床、摆式圆锯床和立式圆锯床。大圆锯片直径小于315 mm或大于2000 mm的圆锯床可参照本部分使用。

JB/T 3364.3-2011圆锯床.第3部分：技术条件

JB/T 3364的本部分规定了圆锯床的制造与验收的技术条件。本部分适用于大圆锯片直径为315 mm～2000 mm的卧式圆锯床、摆式圆锯床和立式圆锯床。大圆锯片直径小于315 mm或大于2000 mm的圆锯床可参照本部分使用。

JB/T 3364.4-2011圆锯床.第4部分：主轴端部连接尺寸

JB/T 3364的本部分规定了圆锯床主轴端部连接尺寸。本部分适用于新设计的冷锯金属的卧式圆锯床、摆式圆锯床和立式圆锯床。

JB/T 13096.1-2017数控圆锯床 第1部分:型式与参数

JB/T 13096的本部分规定了数控圆锯床的系列构成、型式与参数。本部分适用于新设计的冷锯金属数控圆锯床。

JB/T 13096.2-2017数控圆锯床 第2部分:数控卧式圆锯床 精度检验

JB/T 13096的本部分规定了数控卧式圆锯床的几何精度和工作精度的要求及检验方法。本部分适用于大圆锯片直径为450 mm~1 800 mm、大锯削规格为160 mm~600 mm的数控卧式圆锯床(以下简称机床)。其他规格的数控卧式圆锯床可参照本部分使用。

JB/T 13096.3-2017数控圆锯床 第3部分:数控卧式圆锯床 技术条件

JB/T 13096的本部分规定了数控卧式圆锯床制造与验收的技术要求。本部分适用于大圆据片直径为450 mm~1 800 mm、大据削规格为160 mm~600 mm的数控卧式圆锯床(以下简称机床)。其他规格的数控卧式圆锯床可参照执行。

JB/T 13096.4-2017数控圆锯床 第4部分:数控摆式圆锯床 精度检验

JB/T 13096的本部分规定了数控摆式圆锯床的几何精度、位置精度和工作精度的要求及检验方法。本部分适用于大圆锯片直径为250 mm~800 mm、大锯削规格为50 mm~260 mm的数控摆式圆锯床(以下简称机床)。其他规格的数控摆式圆锯床可参照本部分执行。

JB/T 13096.5-2017数控圆锯床 第5部分:数控摆式圆锯床 技术条件

JB/T 13096的本部分规定了数控摆式圆锯床制造与验收的技术要求。本部分适用于大圆锯片直径为250 mm~800 mm、大锯削规格为50 mm~260 mm的数控摆式圆锯床(以下简称机床)。其他规格的数控摆式圆锯床可参照本部分执行。

JB/T 14480.1-2023数控旋转圆锯床 第1部分：精度检验

本文件规定了数控旋转圆锯床的轴线代号与命名、一般要求、几何精度检验、数控轴线的定位精度与重复定位精度检验及工作精度检验。\r本文件适用于大圆锯片直径250mm～800mm，大锯削规格50mm～200mm的数控旋转圆锯床精度的检验活动。

JB/T 14480.2-2023数控旋转圆锯床 第2部分：技术规范

本文件规定了数控旋转圆锯床的一般要求、附件和工具、加工与装配质量、机床噪声、机床安全卫生、机床空运转试验、机床负荷试验及机床精度检验。\r本文件适用于大圆锯片直径250mm～800mm，大锯削规格50mm～260mm的数控旋转圆锯床的制造。

EN 12267+A1-2010食品加工机械.圆锯床.安全和卫生要求

This European Standard specifies requirements for the design and manufacturing of circular saw machines (see Figures 1 and 2). The machines covered by this European Standard are used to cut bone and meat. The circular saw machines covered by this European Standard do not include circular saw machines for processing of wood and similar materials and the requirements of EN 1870-1 do not apply. Circular saw machines for domestic use are not included in this European Standard. This European Standard applies only to machines which are manufactured after the date of issue of this European Standard. This European Standard covers the following types of machines: Circular saw machines with a feed table and a fixed product pusher The distance \"A\" from the floor to the top surface of the feed table is from 800 mm to 1050 mm. The saw blade diameter is between 350 mm and 400 mm (see Figure 1). Circular saw machines installed in a cutting line (e. g. conveyor belt or roller conveyor), e. g. with a protective component which can be lifted on the feed and discharge side. The saw blade diameter is between 350 mm and 400 mm (see Figure 2). Key 12345678910111213 Product pusher Handle Feed table Interlocking switch for feed table ON / OFF switch Chip pan Operator side Protective hood Hinge Saw blade 350 mm - 400 mm diameter Interlocking switch for chip pan Machine rack Locking device 12345 Protective hood Roller conveyor or belt conveyor Feed side Casing Chip pan Figure 1 - Circular saw machine with machine base Figure 2 - Circular saw machine in cutting line Circular saw machines comprise a machine base, a fixed, foldable feed table, a product pusher, a protective hood which can be lifted, a saw blade, a drive and electrical components, depending on machine type. Circular saw machines with a machine base can be wheel-mounted (see Figure 1). This European Standard deals with all significant hazards, hazardous situations and events relevant to circular saw machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard deals with the hazards which can arise during commissioning, operation, cleaning, use, maintenance and decommissioning of the machine. On floor-type circular saw machines (see Figure 3) the product to be cut is placed by hand onto the feed table and pushed against the cutting zone of the saw blade by means of the product pusher and sawed. On circular saw machines which are installed in a cutting line (see Figure 4) the product to be cut is pushed by hand via the conveyor belt or roller conveyor against the cutting zone of the saw blade and sawed.

EN 12267-2003食品加工机械.圆锯床.安全和卫生要求.包含修改件A1-2010

This European Standard specifies requirements for the design and manufacturing of circular saw machines (see Figures 1 and 2). The machines covered byThis European Standard are used to cut bone and meat. The circular saw machines covered byThis European Standard do not include circular saw machines for processing of wood and similar materials and the requirements of EN 1870-1 do not apply. Circular saw machines for domestic use are not included inThis European Standard.This European Standard applies only to machines which are manufactured after the date of issue of this European Standard.This European Standard covers the following types of machines: Circular saw machines with a feed table and a fixed product pusher The distance \"A\" from the floor to the top surface of the feed table is from 800 mm to 1050 mm. The saw blade diameter is between 350 mm and 400 mm (see Figure 1). Circular saw machines installed in a cutting line (e. g. conveyor belt or roller conveyor), e. g. with a protective component which can be lifted on the feed and discharge side. The saw blade diameter is between 350 mm and 400 mm (see Figure 2). Key 12345678910111213 Product pusher Handle Feed table Interlocking switch for feed table ON / OFF switch Chip pan Operator side Protective hood Hinge Saw blade 350 mm-400 mm diameter Interlocking switch for chip pan Machine rack Locking device 12345 Protective hood Roller conveyor or belt conveyor Feed side Casing Chip pan Figure 1-Circular saw machine with machine base Figure 2-Circular saw machine in cutting line Circular saw machines comprise a machine base, a fixed, foldable feed table, a product pusher, a protective hood which can be lifted, a saw blade, a drive and electrical components, depending on machine type. Circular saw machines with a machine base can be wheel-mounted (see Figure 1).This European Standard deals with all significant hazards, hazardous situations and events relevant to circular saw machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).This European Standard deals with the hazards which can arise during commissioning, operation, cleaning, use, maintenance and decommissioning of the machine. On floor-type circular saw machines (see Figure 3) the product to be cut is placed by hand onto the feed table and pushed against the cutting zone of the saw blade by means of the product pusher and sawed. On circular saw machines which are installed in a cutting line (see Figure 4) the product to be cut is pushed by hand via the conveyor belt or roller conveyor against the cutting zone of the saw blade and sawed.

NF E64-607-9-2012木工机械的安全性.圆形电锯.第9部分:手工装载和/或卸载的整体送料横切用双刃锯条圆锯床

La présente Norme européenne traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, tels qu'énumérés à l'Article 4, applicables aux machines à scier à deux lames de scie circulaires, pour tronçonnage, à avance mécanisée et à chargement et/ou déchargement manuels, ci-après désignées \"machines\". Ce sont des machines conçues pour la coupe de bois massif, de panneaux de particules, de panneaux de fibres, de contreplaqué ainsi que ces matériaux lorsque leurs surfaces ou leurs chants sont recouverts de matière plastique et/ou de plastique/alliages légers stratifiés, lorsqu'elles sont utilisées normalement et dans les conditions prévues par le fabricant, incluant une mauvaise utilisation raisonnablement prévisible.Le présent document n'est pas applicable aux : machines conçues pour le tronçonnage de grumes ; tronçonneuses à deux lames à coupe ascendante.Le présent document n'est pas applicable aux machines fabriquées avant la date de sa publication comme norme EN.

TS EN 12267+A1-2013食品加工机械. 圆锯床. 安全和卫生要求

This European Standard specifies requirements for the design and manufacturing of circular saw machines (see Figures 1 and 2). The machines covered by this European Standard are used to cut bone and meat. The circular saw machines covered by this European Standard do not include circular saw machines for processing of wood and similar materials and the requirements of EN 1870-1 do not apply. Circular saw machines for domestic use are not included in this European Standard. This European Standard applies only to machines which are manufactured after the date of issue of this European Standard. This European Standard covers the following types of machines: Circular saw machines with a feed table and a fixed product pusher - The distance \"A\" from the floor to the top surface of the feed table is from 800 mm to 1050 mm. The saw blade diameter is between 350 mm and 400 mm (see Figure 1). - Circular saw machines installed in a cutting line (e.g. conveyor belt or roller conveyor), e.g. with a protective component which can be lifted on the feed and discharge side. The saw blade diameter is between 350 mm and 400 mm (see Figure 2).