电缆电缆及其原材料检测

发布时间：2024-06-21 作者：中析研究所浏览：

CJJ 167-2012城市轨道交通直线电机牵引系统设计规范

本规范适用于采用直线电机非粘着驱动、车辆装设短定子、轨道中部设置感应板、钢轮/钢轨作为支撑和导向、列车高速度为100km/h的新建城市轨道交通直线电机牵引系统工程的设计。

SJ 30030.10-2018宇航级和高可靠电连接器工艺控制要求第10部分:组件端接

本部分规定了宇航级和高可靠电连接器(以下简称宇高电连接器)组件端接工艺控制中人员、设备、材料、工艺过程、生产环境、禁限用工艺控制及检验要求等内容。本部分适用于宇高电连接器组件端接工艺过程的控制与检验。

EN ISO 13628-5-2009石油和天然气工业.水下采油系统的设计和操作.第5部分:海底缆线

This International Standard specifies the general, and some of the special, requirements on materials used for the construction of equipment used in gas welding, cutting and allied processes.

DIN EN 4056-001-2015航空航天系列.导线电缆扎匝.第001部分:技术规范;德文和英文版本EN 4056-001-2015

This European Standard specifies the characteristics, test methods, qualification and acceptance conditions of plastic cable ties, used for the bundling, fixing and/or marking of cable harnesses in aircraft. The cable ties should be installed with a qualified application tool, which controls the application force thus avoiding damage to the cable insulation. It defines the aerospace requirements not specified in EN 62275.

DIN EN ISO 13628-5-2010石油和天然气工业.水下采油系统的设计和操作.第5部分:海底缆线

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surface-subsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.

BS 6739-2009过程控制系统仪表的实施规范:安装设计和实施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.

BS EN 50411-2-5-2009光纤通信系统用纤维组织和闭合.产品规范.1型S&A类鼓风纤维微管道电缆用密封闭路

This specification contains the initial, start of life dimensional, optical, mechanical and environmental performance requirements which a fully installed blown fibre protected microduct closure must meet in order for it to be categorised as an EN standard product.These products are suitable for installation of and use with microduct fibre units, microduct optical fibre cables, microduct and protected microduct as defined within EN 60794-5.

BS EN 50411-2-9-2010光纤通信系统用纤维形成体和闭路.产品规范.S&A类鼓风纤维微管道电缆用非密封闭路

This specification contains the initial, start of life dimensional, mechanical and environmental performancerequirements which a fully installed blown fibre protected, non-sealed closure for duct and microductcable, must meet in order for it to be categorised as an EN standard product.These products are suitable for installation of and use with microduct fibre units, microduct optical fibrecables, microduct and protected microduct as defined within EN 60794-5.When the non-sealed closures are installed in subterranean environments it is mandatory to use sealedABF connectors meeting EN 50411-2-8 in order to guarantee the expected network performance andreliability.

BS EN ISO 13628-5-2009石油和天然气工业.水下采油系统设计和操作.水下脐带管

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.This part of ISO 13628 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.This part of ISO 13628 applies to umbilicals for static or dynamic service, with surface-surface, surfacesubsea and subsea-subsea routings.This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.This part of ISO 13628 applies only to tubes with the following dimensions: wall thickness, t < 6 mm, internal diameter, ID < 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.This part of ISO 13628 does not apply to a tube or hose rated lower than 7 MPa (1 015 psi).This part of ISO 13628 does not apply to electric cable voltage ratings above standard rated voltagesU0/U(Um) = 3,6/6(7,2) kV rms, where U0, U and Um are as defined in IEC 60502-1 and IEC 60502-2.