橡胶绝缘低压电缆检测

GB 50303-2015建筑电气工程施工质量验收规范

本规范适用于电压等级为35kV及以下建筑电气安装工程的施工质量验收。

GB 50536-2009煤矿综采采区设计规范

本规范适用于新建、改建及扩建的矿井可行性研究、初步设计和施工图等各阶段的综采采区设计,以及生产矿井的综采采区设计。

GB 51145-2015煤矿电气设备安装工程施工与验收规范

本规范适用于煤矿建设电气设备安装工程的施工及验收。

YB 4408-2014高炉TRT系统电气设备安装工程施工验收规范

本规范适用于高炉TRT系统电气设备安装工程施工验收。

CJJ 89-2012城市道路照明工程施工及验收规程

本标准适用于电压为10kV及以下城市道路照明工程的施工及验收。工程施工时应按批准的设计图纸进行施工。

JTJ 280-2002港口设备安装工程技术规范

本规范适用于新建、改建和扩建港口设备安装工程的施工及验收。

DB50/T 283-2008城市道路维护工程施工及验收规程

本标准规定了城市道路维护工程施工及验收工作的技术规则，包括术语、基本规定、路面、路基、人行道、广场及附属设施、排水、架空线路、低压电缆线路、道路照明装置、变压器、箱式变电站、配电装置、控制系统及接地装置等内容。本标准适用于重庆市辖区内城市道路维护工程的施工及验收。本标准不适用于桥梁、隧道、绿化等维护工程。

UL 1838-2003低压景观照明系统

Applies to low-voltage landscape lighting systems and components that may consist of an isolating type power unit, wiring, and luminaire. Only covers equipment where the maximum output of each secondary circuit is 25 A, 15 V ac (21.2 V peak) open circuit voltage, 300 VA. The luminaires intended for garden, walkway, patio areas, or similar outdoor locations and for certain indoor locations such as atriums and shopping malls. The power units may be installed indoors or outdoors. The equipment is intended to be installed in accordance with the National Electrical Code, ANSI/NFPA 70.

BS 6195-2006电缆.线圈端导线用橡胶或硅橡胶绝缘软电缆及电线

This British Standard specifies requirements for various types ofinsulation, voltage categories and dimensions for a standard range ofinsulated flexible cables and flexible cords (commonly known as “coilend leads”), that are intended to be connected directly and permanentlyto a coil winding or other component of electrical apparatus.The types of cable specified in this standard are as follows:Type 4 cable, voltage categories A, C, D, E and F, for a designatedtemperature of 90 °C (flame retardant, rubber insulated coil leads);Type 5 cable, voltage categories A, C, D, E and F, for a designatedtemperature of 180 °C (180 °C silicone rubber insulated coil leads).NOTE A guide to the use of the cables specified in this British Standard isgiven in Annex A. A summary of the tests applicable to the cables is given inAnnex B.

BS 8512-2008电缆.木制卷筒上电缆的储存、处理、安装和处置用实施规程

This British Standard gives recommendations for the storage andhandling of cables for fixed installations, rated up to 1 900/3 300 V, thatare packaged on wooden cable drums suitable for storage outdoors.NOTE The recommendations could also be applied to:• cables of higher rated voltages that are packaged on wooden drums;and• cables of similar size, on similar wooden drums, and made tostandards and specifications not specifically quoted here.This standard does not cover metal drums, cable spools or cable reels,or trailing and reeling cables.

BS EN 45510-2-9-2008发电站设备的采购指南.电气设备.布线系统

This standard gives guidance on writing the technical specification for the procurement of equipment for use inelectricity generating stations (power stations). This Guide for procurement is not applicable to equipment for use inthe nuclear reactor plant area of nuclear power stations. Other possible applications of such equipment have notbeen considered in the preparation of this Guide.This Guide on cabling systems deals with a wide range of activities and may be used for any or all of these activitiesby selection of the relevant parts e.g.:- provision of support for cable;- laying of cable;- completion of cable ends;The Guide covers the installation of power cable up to and including 20,8/36 (42) kV and the supply and installation ofcontrol and instrumentation cable. The supply of power cable is covered by EN 45510-2-8.The Guide includes the installation of protective conductor cable for earthing and equipotential bonding up to the mainearthing busbar(s), but not the below ground earth-electrode network.The equipment covered by this Guide is defined by its function rather than design type. Therefore, the guidance tothe specification is stated in performance terms rather than being specified by a detailed description of theequipment to be supplied.This Guide indicates to potential purchasers how their specification should be prepared so that- the equipment type and capacity interfaces correctly with other elements of the systems,- predicted performance is achieved,- ancillary equipment is properly sized,- reliability, availability and safety requirements are achieved,- proper consideration is given to the evaluation process and the quality measures to be applied.This Guide does not determine the type of specification (e.g. detailed, performance, functional) or the extent ofsupply for any given contract which is normally decided on the basis of the purchaser's project strategy. It does notcover- any commercial, contractual or legal issues which are normally in separate parts of an enquiry,- any allocation of responsibilities which are determined by the contract.This Guide does not prescribe the arrangement of the documents in the enquiry.NOTE As a comprehensive European environmental policy is still under preparation, this Guide does not address theenvironmental implications of the equipment.

BS EN 50143-2009无荷载额定输出电压大于1000 V小于等于10000 V的信号和发光放电管装置用电缆

EN 50143 applies to single core cables of rated voltages up to and including 5/10 kV (Uo/U) used with electricsigns and high-voltage luminous-discharge-tube installations. These cables are for use in installationscomplying with EN 50107.The particular types of cables are specified in Clauses 7 to 10 of this standard.

BS EN 61138-2007便携式接地和短路设备用电缆

This International Standard applies to flexible cables with insulation based on ethylenepropylene rubber (EPR), polyvinyl chloride (PVC) or silicone rubber (SiR) for portable earthingand short-circuiting equipment.For this type of cable no rated voltage is given as such cables are exclusively intended forearthing and short-circuiting equipment.The particular types of cable and their code designations are specified in Clause 6 of thisstandard.The test methods specified in this standard are given in }EN 50395, EN 50396~,IEC 60811 and IEC 62230.NOTE In addition to the requirements given in this standard, mechanical requirements and requirements for themarking for the complete equipment should be taken into account. These requirements can be found in IEC 61230.