灭火器压力指示器检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB 4351.1-2005手提式灭火器第1部分;性能和结构要求

本部分规定了手提式灭火器的定义、分类、规格与型号、技术要求、试验方法、检验规则、标志等要求。本部分适用于手提式灭火器。

GB/T 4351.3-2005手提式灭火器第3部分;检验细则

本部分规定了以控制和验收手提式灭火器(以下简称灭火器)安全与质量性能为目的的计数抽样检查规则。本部分适用于产品质量检验部门对经生产定型后，稳定连续生产的灭火器，作成批出厂或入库时产品质量的验收检查，适用于对产品作定型检验时，生产过程稳定性的检查及定型后核实是否继续保持规定稳定性的周期检查。产品的质量监督检查及订货合同等技术文件可引用并执行本部分的规定。

GB 7258-2017机动车运行安全技术条件

本标准规定了机动车的整车及主要总成、安全防护装置等有关运行安全的基本技术要求，以及消防车、救护车、工程救险车和警车及残疾人专用汽车的附加要求。本标准适用于在我国道路上行驶的所有机动车，但不适用于有轨电车及并非为在道路上行驶和使用而设计和制造、主要用于封闭道路和场所作业施工的轮式专用机械车。

GB 8109-2005推车式灭火器

本标准规定了推车式灭火器的定义、分类、灭火剂、驱动气体、充装量和型号、性能要求、试验方法、检验规则和标志等要求。本标准适用于总质量大于25kg，但不大于450kg的推车式灭火器。本标准不适用于灭D类火的推车式灭火器。

GB 16151.1-2008农业机械运行安全技术条件.第1部分:拖拉机

GB 16151的本部分规定了拖拉机的整机及其发动机、传动系、行走系、转向系、制动系、照明及信号等装置、液压悬挂及牵引装置、驾驶室等部件有关运行安全和排气污染物控制、噪声控制的基本技术要求。本部分适用于在我国使用的轮式、履带和手扶拖拉机和拖拉机运输机组的安全检验，其他用于农业作业的具有拖拉机功能的动力机械参照使用。

GB/T 34031-2017船用产品点火保护试验方法

本标准规定了使用丙烷和空气混合气体测试船用产品点火保护功能的试验要求、程序和方法。本标准适用于船用产品点火保护功能的试验和验收，船用防爆设备、本质安全设备以及在氢和空气混合气体中使用的部件可参照使用。

GB 50444-2008建筑灭火器配置验收及检查规范

本规范适用于工业与民用建筑中灭火器的安装设置、验收、检查和维护。本规范不适用于生产或储存炸药、弹药、火工品、花炮的厂房或库房。

HB 7583-1998飞机区域安全性分析

本标准规定了飞机区域安全性分析的程序与准则。　　本标准适用于军用和民用飞机区域安全性分析。直升机也可参照执行。

SY/T 6628-2005陆上石油天然气生产环境保护推荐作法

本标准为陆上石油天然气提供了环境保护的可靠作法，适用于承包商和作业者。本标准适用于所有生产设施和采出水处理设施。作业范围包括从井场到道路设计、修建直至油井报废、井场恢复作业、天然气加压传输或开发作业。本标准不包括注气采油。

SY/T 6776-2010海上生产设施设计和危险性分析推荐作法

本推荐作法为敞开式海上平台生产设施的设计和布置推荐了低要求和指南，同时对海上生产设施的各种基本风险分析程序进行统一简要的描述。本推荐作法对几种适用于平台风险分析的程序进行了讨论，并对工艺安全信息和风险分析提出了低要求。以满足API RP 75的要求。本推荐作法针对常规生产作业有关的永久性和临时性的设施。所给出的指导原则与相关行业规范、作法和标准结合使用后应能达到可接受的安全等级。

WS/T 442-2014临床实验室生物安全指南

本标准规定了二级(涵盖一级)生物安全防护级别临床实验室的设施、设备和安全管理的基本要求。本标准适用于涉及生物因子操作的临床实验室。

TB 10014-2012铁路工程地质钻探规程

本规程适用于铁路工程地质、水文地质钻探及物探测井、孔内测试钻孔的钻探工作。

UL 8-2005水基试剂灭火器

1.1 These requirements cover the construction and performance, exclusive of performance during fire tests, of portable water based agent fire extinguishers. These fire extinguishers are intended to be utilized in accordance with the Standard for Portable Fire Extinguishers, NFPA 10 and with the National Fire Code of Canada. 1.2 The requirements for performance during fire testing of water based agent fire extinguishers are specified in the Binational Standard for Rating and Fire Testing of Fire Extinguishers, ANSI/UL 711 CAN/ULC-S508. 1.3 As used in these requirements, the term \"extinguisher\" refers to all extinguishers or any part thereof covered by these requirements, unless specifically noted otherwise. This new edition of ANSI/UL 8 CAN/ULC-S554 is a binational standard that has been harmonized with the requirements of Canada. This edition includes a title change, an expansion of the standard scope to specify Canadian installation requirements, reorganized and renumbered requirements, and the addition of operating instructions pictographs to the marking section.

EN 3-10-2009便携式灭火器.第10部分:提供与EN 3-7一致的便携式灭火器评估［代替:CEN EN 3-6］

This European Standard specifies the minimum requirements for attesting the conformity of portable fire extinguishers to EN 3-7, as well as the requirements for the quality and production control of the fire extinguishers. It specifies the documentation to be provided regarding: identification of the applicant; identification of the manufacturer, if not the applicant; identification of subcontractor(s), if applicable; identification of the extinguisher; documents provided with the extinguisher; CE marking; quality management system; extinguishing media toxicological information. It specifies methods for: type testing; factory assessment; controls during production. NOTE 1 A test report and a satisfactory audit supporting documentation could form the basis for an applicant to request a certification of his product from an EA accredited certification body. Additional requirements can be made by national regulations and/or quality marks. NOTE 2 Where appropriate, component family testing could be applied.

EN 746-2-2010工业热加工工艺设备.燃烧和燃料储运系统安全要求

This part of EN 746 together with EN 746-1 specifies safety requirements for single and multiple burners that are part of Industrial Thermoprocessing Equipment. (InThis standard referred to as IThE).This document deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems that are part of IThE as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.This European Standard covers: fuel pipework downstream of and including the manual isolating valve; burner(s), burner system and ignition device; safety related control system (protective system).This European Standard applies to any oxidation with air or other gases containing free oxygen of gaseous, liquid and solid fuels or any combustion of them to release thermal energy. For thermal or catalytic post combustion and waste incineration,This European Standard applies only to auxiliary burners designed to start-up and/or support the process. The pressure hazard of the piping and components covered byThis standard is within the limits of maximum pressure/size relationship as described in normative Annex E.This European Standard also gives the necessary requirements for the information for use.This European Standard does not cover hazards from heating generated by electricity.This European Standard does not deal with the hazards created by the release of flammable substances from the products processed in the IThE. NOTE EN 1539, Dryers and ovens, in which flammable substances are released-Safety requirementsThis European Standard is not applicable to combustion and fuel handling systems of welding and soldering machines; up-stream of the IThE manual isolating valve.This European Standard is not applicable to electricity cabling and power cabling upstream of the IThE control panel/protective system. Noise can be a significant hazard for combustion and fuel handling systems. It is not dealt with inThis standard.This European Standard is not applicable to combustion and fuel handling systems as part of IThE which is manufactured before the date of its publication as EN.