钻井液用乳化剂检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 21412.1-2010石油天然气工业水下生产系统的设计与操作第1部分：一般要求和推荐做法

本部分制定了整套水下生产系统从设计到废弃各个阶段的一般要求和推荐做法，作为一个纲领性文件用于指导和制定涉及到水下生产系统各个组成部分更为详细要求的子系统标准。同时，对于子系统标准内未包括的某些部分，如系统设计、结构、管汇、吊装设备、颜色和标记等，也给出了较为详细的要求。对那些应用范围有限的特种设备，如密闭在干式舱中的组合式采油树、采油树和管汇等，这里未做专门讨论，但本部分中的相关条款同样适用于这类设备。

GB/T 28911-2012石油天然气钻井工程术语

本标准规定了石油天然气钻井工程专用的术语。本标准适用于石油天然气钻井工程领域，也适用于石油天然气工业的其他领域。

GB/T 29170-2012石油天然气工业钻井液实验室测试

本标准规定了钻井液材料和钻井液的物理、化学、流变等性能的实验室测试方法。本标准适用于水基钻井液、油基钻井液以及其他基液或人工配制流体。本标准不适用于作为控制钻井液性能的详细手册。由于搅拌条件和测试温度对钻井液性能影响显著,本标准给出了推荐的搅拌条件和测试温度。

GB/T 34903.1-2017石油、石化与天然气工业与油气开采相关介质接触的非金属材料第1部分:热塑性塑料

GB/T 34903的本部分规定了服役于石油与天然气生产设备中的非金属材料选用与评价的一般原则、基本要求、推荐做法以及产品质量保证指南。非金属材料失效导致的设备损坏会造成公众健康、人员安全与环境风险。本部分有助于避免设备发生这种高昂代价的腐蚀损坏。本部分补充而不是代替设备设计准则、标准或法律规范中已有的材料技术要求。GB/T 34903的本部分规定了石油天然气工业中使用的热塑性塑料材料类型、性能要求、制造要求、相容性评价方法和相容性技术指标判据。本部分适用于但不限于以下设备:非金属管线、管道、衬里、密封件、垫圈和密封圈。本部分不一定适用于炼油化工或石油天然气工业下游加工装置及设备。

SY/T 5745-2008采油采气工程词汇

本标准规定了采油采气工程常用词汇。本标准适用于石油天然气工业采油采气工程领域，也适用于石油工业其他领域。

SY/T 5794-2010钻井液用沥青类评价方法

本标准规定了钻井液用沥青类产品挥发份、pH值、沥青总量、水溶物含量、油溶物含量、电动电位、软化点等的测定方法。本标准适用于钻井液用沥青类产品挥发份、pH值、沥青总量、水溶物含量、油溶物含量、电动电位、软化点等的测定。

SY/T 6615-2005钻井液用乳化剂评价程序

本标准规定了钻井液用乳化剂的技术要求及评价方法。本标准适用于钻井液用W/O型、O/W型乳化剂。

EN ISO 10416-2009石油和天然气工业.钻探泥浆.实验室试验

EN ISO 13628-1-2005石油和天然气工业.水下采油系统的设计和操作.第1部分:一般要求和建议 ISO 13628-1-2005

This part of ISO 13628 provides general requirements and overall recommendations for development of complete subsea production systems, from the design phase to decommissioning and abandonment.This part of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with more detailed requirements for the subsystems which typically form part of a subsea production system. However, in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) more detailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbons from one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floating or subsea) or onshore, or to inject water/gas through subsea wells.This part of ISO 13628 and its related subsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are not specifically discussed because of their limited use. However, the information presented is applicable to those types of equipment.If requirements as stated inThis part of ISO 13628 are in conflict with, or are inconsistent with, requirements as stated in the relevant complementary parts of ISO 13628, then the specific requirements in the complementary parts take precedence.

DIN EN ISO 10414-2-2011石油和天然气工业.钻井液的现场测试.第2部分:油基液(ISO 10414-2-2011);英文版本EN ISO 10414-2-2011,仅限CD-ROM

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-based drilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluid balances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).

DIN EN ISO 10416-2010石油和天然气工业.钻井液.实验室试验

DIN EN ISO 13628-1-2010石油和天然气工业.水下生产系统的设计和操作.第1部分:一般要求和推荐规范(ISO 13628-1-2005 + Amd 1-2010).英文版本EN ISO 13628-1-2005 + A1-2010,只光盘版

BS EN ISO 10414-2-2011石油和天然气工业.钻井液的现场测试.油基液

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-baseddrilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluidbalances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).

BS EN ISO 10416-2009石油和天然气工业.钻探泥浆.实验室试验

This International Standard provides procedures for the laboratory testing of both drilling fluid materials anddrilling fluid physical, chemical and performance properties. It is applicable to both water-based and oil-baseddrilling fluids, as well as the base or “make-up” fluid.It is not applicable as a detailed manual on drilling fluid control procedures. Recommendations regardingagitation and testing temperature are presented because the agitation history and temperature have aprofound effect on drilling fluid properties.

BS EN ISO 13628-1-2005+A1-2010石油和天然气工业.水下采油系统的设计和操作.第1部分:一般要求和推荐规范

This part of ISO 13628 provides general requirements and overall recommendations for development ofcomplete subsea production systems, from the design phase to decommissioning and abandonment. Thispart of ISO 13628 is intended as an umbrella document to govern other parts of ISO 13628 dealing with moredetailed requirements for the subsystems which typically form part of a subsea production system. However,in some areas (e.g. system design, structures, manifolds, lifting devices, and colour and marking) moredetailed requirements are included herein, as these subjects are not covered in a subsystem standard.The complete subsea production system comprises several subsystems necessary to produce hydrocarbonsfrom one or more subsea wells and transfer them to a given processing facility located offshore (fixed, floatingor subsea) or onshore, or to inject water/gas through subsea wells. This part of ISO 13628 and its relatedsubsystem standards apply as far as the interface limits described in Clause 4.Specialized equipment, such as split trees and trees and manifolds in atmospheric chambers, are notspecifically discussed because of their limited use. However, the information presented is applicable to thosetypes of equipment.If requirements as stated in this part of ISO 13628 are in conflict with, or are inconsistent with, requirementsas stated in the relevant complementary parts of ISO 13628, then the specific requirements in thecomplementary parts take precedence.

BS EN ISO 23936-1-2009石油,石化和天然气工业.与石油和天然气生产相关的介质接触的非金属材料.第1部分:热塑性塑料(ISO 23936-1-2009)

ISO 23936 as a whole presents general principles and gives requirements and recommendations for theselection and qualification, and gives guidance for the quality assurance, of non-metallic materials for service in equipment used in oil and gas production environments, where the failure of such equipment could pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help to avoid costly corrosion failures of the equipment itself. It supplements, but does not replace, the material requirements given in the appropriate design codes, standards or regulations.This part of ISO 23936 addresses the resistance of thermoplastics to the deterioration in properties that can be caused by physical or chemical interaction with produced and injected oil and gas-field media, and with production and chemical treatment. Interaction with sunlight is included; however, ionizing radiation is excluded from the scope of this part of ISO 23936.Furthermore, this part of ISO 23936 is not necessarily suitable for application to equipment used in refining or downstream processes and equipment.The equipment considered includes, but is not limited to, non-metallic pipelines, piping, liners, seals, gaskets and washers.