百叶窗用铝合金带材检测

百叶窗用铝合金带材检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 19775-2005玻璃-金属封接式热管真空太阳集热管

本标准规定了玻璃-金属封接式热管真空太阳集热管的术语和定义、分类与命名、技术要求、检测方法、检验规则及标志、包装、运输、贮存。 本标准仅适用于玻璃-金属封接式热管真空太阳集热管。

GB/T 37256-2018建筑室外用格栅通用技术要求

本标准规定了建筑室外用格栅的术语和定义、分类和标记、材料、一般要求、要求和试验方法。本标准适用于建筑外围护结构中的固定格栅。

LY/T 2885-2017竹百叶窗帘

本标准规定了竹百叶窗帘的术语和定义、分类、要求、检验方法、检验规则以及标志、包装、运输和贮存。本标准适用于室内用竹质百叶窗帘。

JG/T 251-2017建筑用遮阳金属百叶帘

本标准规定了建筑用遮阳金属百叶帘的分类、代号及标记、材料和配件、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于建筑用外遮阳、内遮阳、中间遮阳的金属百叶帘。本标准不适用于内置遮阳中空玻璃用金属百叶帘。

JG/T 274-2018建筑遮阳通用技术要求

本标准规定了建筑遮阳产品的术语和定义、分类和标记、材料及配件、要求和试验方法等。本标准适用于安装在建筑物上的遮阳产品，包括外遮阳产品、内遮阳产品和中间遮阳产品。

NF P28-002-1-2-2008建筑施工工程.隔墙.第1-2部分:材料选择用一般标准

Le présent document a pour objet de fixer les critères généraux de choix des matériaux utilisés pour la réalisation de façades telles que définies dans le domaine d'application de la NF DTU 33.1 P1-1 (CCT).

DIN EN ISO 13706-2012石油、石化和天然气工业.风冷热交换器

This International Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum, petrochemical and natural gas industries. This International Standard is applicable to air-cooled heat exchangers with horizontal bundles, but the basic concepts can also be applied to other configurations.

BS 1703-2005垃圾道和垃圾斗规范

This British Standard specifies requirements for gravity transport systems for refuse in multi-storey buildings, consisting of refuse chutes in the form of one or more vertical pipes, complete with hoppers, receiving refuse from successive floors in a building and discharging it into a refuse storage system.

BS 7412-2007未增塑聚氯乙烯(PVC-U)挤制空心型窗和门具规范

This British Standard specifies requirements for the design, fabricationand performance of windows and glazed doorsets made from PVC-Uextruded hollow profiles.This British Standard applies to windows and doorsets manufacturedfrom PVC-U hollow profiles incorporating fusion welded corner joints.It applies to windows and doors fabricated into frames in a factory, tobe installed vertically (within 15°) into the external face of buildings, assingle or multi-light units, in coupled assemblies when appropriate, ofthe following types:a) windows:1) hinged: side-hung (open in or out), top-hung (open out),bottom-hung (open in), tilt and turn or turn before tilt;2) projecting: side-hung (open in or open out) and top-hung(open out or reversible);3) pivoted: horizontal and vertical (hung centrally or off-centre)including reversible;4) sliding: horizontal and vertical;5) side-hung: fully reversible;6) fixed light;b) doors:1) single leaf single-swing doors with or without side lights andtop panels;2) double leaf single-swing doors with or without side lights andtop panels.It is applicable to assemblies in which any frame member is not longerthan 3 m. It does not apply to curtain walls that span across horizontalstructural members of floors but is applicable to windows within acurtain walling system.It is applicable to assemblies up to the point of installation.NOTE Guidance on the evaluation of conformity is given in Annex A.Guidance on durability and recycling is given in Annex B.

BS EN 62109-1-2010光电电力系统中使用的电源转换器安全性.第1部分:一般要求

This part of IEC 62109 applies to the power conversion equipment (PCE) for use inPhotovoltaic (PV) systems where a uniform technical level with respect to safety is necessary.This standard defines the minimum requirements for the design and manufacture of PCE forprotection against electric shock, energy, fire, mechanical and other hazards.This standard provides general requirements applicable to all types of PV PCE. There areadditional parts of this standard that provide specific requirements for the different types ofpower converters, such as Part 2 - inverters. Additional parts may be published as newproducts and technologies are commercialised.