溶解乙炔气瓶阀检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 8335-2011气瓶专用螺纹

本标准规定了气瓶用圆锥螺紋和圆柱管螺纹的术语、符号、基本牙型和尺寸。本标准适用于气瓶的瓶口与瓶阀连接的圆锥螺纹、瓶帽与颈圈连接的圆柱管螺纹（以下简称圆柱螺纹）。带安全装置气瓶的易熔塞与塞座连接的圆锥螺纹也可参照本标准使用。

GB/T 8337-2011气瓶用易熔合金塞装置

本标准规定了易熔合金塞装置（以下简称\"易熔塞装置\"）的制造、检验、试验和验收的基本要求。本标准适用于安装在气瓶上的易熔塞装置，气瓶阀用易熔合金可参考本标准的规定。

GB 9448-1999焊接与切割安全

本标准规定了在实施焊接、切割操作过程中避免人身伤害及财产损失所必须遵循的基本原则。本标准为安全地实施焊接、切割操作提供了依据。

GB/T 12135-2016气瓶检验机构技术条件

本标准规定了气瓶定期检验机构(以下简称“检验机构”)的技术条件。本标准适用于从事无缝气瓶(含钢质无缝气瓶、铝合金无缝气瓶、不锈钢无缝气瓶和汽车用压缩天然气钢瓶)、焊接气瓶(含钢质焊接气瓶和不锈钢焊接气瓶)、液化石油气钢瓶(含液化石油气钢瓶和液化二甲醚钢瓶)、车用液化石油气钢瓶(含车用液化石油气钢瓶和车用液化二甲醚钢瓶)、溶解乙炔气瓶、缠绕气瓶[包括小容积金属内胆纤维缠绕气瓶、金属内胆纤维环缠绕气瓶(含车用)和金属内胆纤维全缠绕气瓶(含车用)]、绝热气瓶(含焊接绝热气瓶和汽车用液化天然气气瓶)的检验机构。本标准不适用于站用气瓶、长管拖车及管束式集装箱用大容积无缝气瓶的检验机构。

GB/T 13076-2009溶解乙炔气瓶定期检验与评定

本标准规定了在用溶解乙炔气瓶(以下简称乙炔瓶)定期检验与评定的基本方法和技术要求。本标准适用于按GB 11638设计、制造的溶解乙炔气瓶。

GB/T 25473-2010焊接、切割及类似工艺用管路减压器

本标准规定了焊接、切割及类似工艺用管路减压器(的定义和命名、符号和单位、制造要求、物理特性、型式试验及程序和标志、使用说明书、包装、贮存、检验规则等要求。本标准适用于将压力在30 MPa以内气瓶压缩气体或甲基乙炔-丙二烯混合物(MPS)、溶解乙炔汇流到总管的高压气体，调节至所需要输出压力的单级和双级管路减压器。本标准不造用于GB/T 7899所述的直接安装在气瓶上的减压器。

GB 26164.1-2010电业安全工作规程.第1部分：热力和机械

本部分规定了从事电力生产的热力和机械作业的人员在生产现场或工作中的基本安全工作要求。本部分适用于从事电力生产的所有人员和进入电力生产现场的有关人员。

GB/T 27550-2011气瓶充装站安全技术条件

本标准规定了压缩气体(亦称永久气体)气瓶充装站、液化气体(包括液化石油气)气瓶充装站、溶解乙炔气瓶充装站(以下简称充装站)的职责和必须具备的安全技术条件。本标准适用于压缩气体(亦称永久气体)气瓶充装站、液化气体(包括液化石油气)气瓶充装站、溶解乙炔气瓶充装站(以下简称充装站)。本标准不适用于车用气瓶和焊接绝热气瓶充装站。

TSG R0006-2014气瓶安全技术监察规程

本规程适用于正常环境温度（-40度~60度，注1-1）下使用，公称容积为0.4L~3000L,公称工作压力为0.2Mpa~35Mpa(表压，下同）且压力与容积的乘积大于或者等于1.0Mpa，盛装压缩气体，高（低）压液化气体，低温液化气体，溶解气体，吸附气体，标准沸点等于或者低于60度的液体以及混合气体（两种或者两种以上气体）的无缝气瓶，焊接气瓶，焊接绝热气瓶，缠绕气瓶，内部装有填料的气瓶以及气瓶附件。

CB 3438-1992船舶修理防火、防爆安全要求

本标准规定了船舶修理过程中各工程部位作业的防火、防爆安全要求。本标准适用于各类钢质船舶和海上工作平台，除另有规定外，也适用于特种船舶和舰艇的修理工程。

LD 55-1994溶解乙炔气瓶质量保证控制要点

本标准规定了钢质焊接式溶解乙炔气瓶制造企业应具备的基本条件、原材料与外购件的质量保证、制造质量与质量检验的控制。本标准适用于基准温度15℃时的限定充装压力小于1.52MPa，高许用温度40℃，公称容积10~60L，内含多孔填料和溶剂，移动式、可重复充气的钢质焊接式溶解乙炔气瓶。

SL 398-2007水利水电工程施工通用安全技术规程

本标准规定了水利水电工程施工的通用安全技术要求。本标准适用于大中型水利水电工程施工安全技术管理、安全防护与安全施工，小型水利水电工程可参照执行。

DIN EN 13807-2017移动式气瓶. 蓄电池车辆和多单元气瓶(MEGC). 设计, 制造, 鉴定和检测; 德文版本EN 13807-2017

This European Standard specifies the requirements for the design, manufacture, identification and testing of battery vehicles and multiple-element gas containers (MEGCs) containing cylinders, tubes or bundles of cylinders. It is applicable to battery vehicles and MEGCs containing compressed gas, liquefied gas and mixtures thereof. It is also applicable to battery vehicles for dissolved acetylene. This European Standard is not applicable to battery vehicles and MEGC for toxic gases with an LC50 value less than or equal to 200 ml/m3. This European Standard applies also to battery vehicles and MEGCs containing bundles of cylinders connected by a manifold which are dis-assembled from the battery vehicle and filled individually. This European Standard does not apply to battery vehicles and MEGCs containing pressure drums or tanks. This European Standard does not specify requirements for the vehicle chassis or motive unit. This European standard does not cover requirements for sea transportation. This European Standard is primarily intended for industrial gases other than Liquefied Petroleum Gases (LPG). At the time of publication of this European Standard, there is no European Standard for dedicated LPG battery vehicles.

DIN EN ISO 2503-2015气焊设备,300巴(30MPa)以下的焊接,切割和相关工艺中使用的气体瓶的压力调节器(ISO 2503-2009+Amd 1-2015);德文版本EN ISO 2503-2009+A1-2015

Due to the new gas letter code specified in ISO 10225, ISO 2503 needed to be amended accordingly.

DIN EN ISO 25760-2015气瓶. 将阀门从气瓶下安全移除的操作程序 (ISO 25760-2009); 德文版本EN ISO 25760-2015

This International Standard is intended for suppliers, operators in testing facilities, operators performing cylinder maintenance and any person authorized to remove valves from gas cylinders. It details procedures for the safe removal of valves from cylinders and includes techniques for the identification of inoperable valves. Only the risks due to gas and gas mixtures under pressure are addressed; other technical issues relating to the removal of a valve from a cylinder are not covered. Some specialized equipment and procedures are in use in parts of the gas industry to safely remove cylinder valves from low pressure gas cylinders while under pressure, e. g. liquefied petroleum gas (LPG); these techniques are not included in this International Standard.

BS EN 13720-2002可运输气瓶.乙炔蓄电池的充电条件

This European Standard specifies the requirements for filling acetylene battery vehicles.

BS EN ISO 22434-2011可运输气瓶.气瓶阀检查和维护

This International Standard specifies the requirements for the inspection and maintenance of cylinder valves,including valves with integrated pressure regulators (VIPR) (see ISO 22435).This International Standard may be applied to cylinder valves at the time of the periodic inspection of gascylinders, bundles, drums and trailers, and at any other time, e.g. at change of gas service (see ISO 11621). Itdoes not apply to routine inspection of cylinder valves carried out at the time of cylinder filling.NOTE National standards and regulations may apply to maintenance of cylinder valves.

KS B 6215-2016溶解乙炔气瓶阀

이 표준은 증기ㆍ공기ㆍ가스ㆍ물ㆍ기름 등의 일반용 배관에 사용하는 강관을 접속하는 강제 용접식 관플랜지 및 블랭크 플랜지(이하 플랜지라 한다.)에서, 기준 치수가 KS B 1511에 따른 압력 호칭 5 K∼30 K의 플랜지에 대하여 규정한다. 또한 플랜지의 강도 확인에 대하여 부속서 A에 기술한다.