ISO 米制精密六角螺拴、螺钉和螺母检测

发布时间：2024-06-21 作者：中析研究所浏览：

ISO 261-1998ISO一般用途米制螺纹直径与螺距系列

This International Standard specifies ISO general purpose metric screw threads (M) having basic profile according to ISO 68-1. Basic dimensions are given in ISO 724. For tolerances see ISO 965-1.

ISO 272-1982紧固件六角产品对边宽度

Specifies the widths to be used in the respective product standards; it sets out a logical ratio between underhead (or nut) bearing area and the tensile stress area of the screw thread.

ISO 606-2015短节距精密传动辊子链和套筒链、附件和辅助链轮

This International Standard specifies the characteristics of\nshort-pitch precision roller and bush chains with associated\nsprockets suitable for the mechanical transmission of power and\nallied applications. It covers dimensions, tolerances, length\nmeasurement, preloading, minimum tensile strengths and minimum\ndynamic strength.\nAlthough Clause 5 applies to chain sprockets for cycles and\nmotor cycles, this International Standard is not applicable to\ntheir chains, which are covered by ISO 9633 and ISO 10190,\nrespectively.

ISO 657-5-1976热轧型钢.第5部分:等边角钢和不等边角钢.米制和英制系列公差

Includes tolerances on leg length, on thickness, cutting tolerance for length, tolerances on mass, straightness and out-of-square.

ISO 691-2005螺钉和螺母用装配工具.扳手和套筒扳手的开口.常用公差

This International Standard specifies tolerances on wrench and socket openings for screws and nuts (or similar parts) having metric width across flats dimensions, as shown diagrammatically below.It gives, for each dimension, the tolerances for general use, defined by its two deviations, minimum and maximum, with respect to the nominal value.These deviations have been determined in relation to the width across flats tolerances for screws and nuts specified in ISO 4759-1 and with regard to the manufacture of tightening tools.

ISO 722-1991凿岩钎具六角形与圆形中空钎钢棒材

Specifies the dimensions for seven nominal sizes. This third edition cancels and replaces the second edition (1985), which has been technically revised (addition of round drill steels and extension of the range of sizes).

ISO 723-1991凿岩钎具六角中空钎杆的锻造钎尾和钎肩

Specifies the dimensions of both forged collared shanks and corresponding chuck bushings. Values are given for five nominal sizes. This second edition cancels and replaces the first edition (1974), which has been technically revised (extension of the range of sizes and specification of the size of the internal diameter at the forged collar).

ISO 727-1-2002压力管件用由未增塑的聚氯乙烯,氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.第1部分:米制系列

This part of ISO 727 specifies the dimensions of plain sockets (cylindrical and conical) in fittings made from unplasticized polyvinyl chloride) (PVC-U), chlorinated polyvinyl chloride) (PVC-C) oracrylonitrile/butadiene/styrene (ABS), intended for connecting by solvent cementing to pipes of the corresponding material for use under pressure. The resulting joint does not require mechanical anchorage.NOTE It is strongly recommended that the advice of the fittings manufacturer be sought in the selection of an appropriate type of solvent cement, depending upon whether the cylindrical or conical type of socketed fitting is being used for a particular installation.

ISO 885-2000普通螺栓和螺钉米制系列头下圆角半径

This International Standard specifies the sizes of the radii under the head and the transition diameters of metric series general purpose bolts and screws.

ISO 887-2000米制普通螺栓、螺钉和螺母用平垫圈总方案

This International Standard specifies the full range of the nominal dimensions of product-grade-A and -C plain washers for general-purpose bolts, screws and nuts of nominal thread diameters ranging from 1 mm to 150 mm inclusive.This International Standard is not applicable to washers for screw and washer assemblies in relation to hole diameters and thicknesses.Information on the use of plain washers is given in annex A.

ISO 887 CORR 1-2006通用米制螺栓、螺钉和螺母用普通垫圈.一般示意图.技术勘误1

This standard is about Plain washers for metric bolts, screws and nuts for general purposes - General plan; Technical Corrigendum 1

ISO 965-1-2013ISO通用米制螺纹. 公差. 第1部分: 原则和基本数据

This part of ISO 965 specifies a tolerance system for ISO general purpose metric screw threads (M) according to ISO 261.The tolerance system refers to the basic profile according to ISO 68-1.

ISO 965-2-1998ISO一般用途米制螺纹. 公差. 第2部分: 一般用途内螺纹和外螺纹的极限尺寸. 中等质量

This part of ISO 965 specifies limits of sizes for pitch and crest diameters for ISO general purpose metric screw threads (M) conforming to ISO 262 having basic profile according to ISO 68-1.The limits of sizes for the tolerance quality specified are derived from the fundamental deviations and tolerances specified in ISO 965-1.

ISO 965-3-2021ISO一般用途米制螺纹. 公差. 第3部分: 螺纹的极限偏差

This document specifies limit deviations for pitch and crest diameters for ISO general purpose metric screw threads (M) conforming to ISO 261 having basic profile in accordance with ISO 68-1. The limit deviations specified are derived from the fundamental deviations and tolerances specified in ISO 965-1. This document is applicable to ISO general purpose metric screw threads with the recommended tolerance classes.

ISO 965-4-2021ISO一般用途米制螺纹. 公差. 第4部分: 热浸镀锌外螺纹的极限尺寸、与其相配的内螺纹镀锌后攻丝、内螺纹的公差带位置为H或G

This document specifies limit deviations and limits of sizes for the pitch and crest diameters of the hot-dip galvanized metric external screw threads conforming to the coarse thread series of ISO 262 (from M8 to M64) having a basic profile according to ISO 68-1. This document is applicable to the hot-dip galvanized metric external screw threads to mate with the internal screw threads tapped with tolerance position H or G after galvanizing.

ISO 965-5-1998ISO一般用途米制螺纹. 公差. 第5部分: 与镀锌前公差带位置为h大尺寸的热沉镀锌外螺纹相配的内螺纹的极限尺寸

This part of ISO 965 specifies deviations and limits of sizes for pitch and crest diameters for ISO general purpose metric internal screw threads conforming to ISO 262 having basic profile according to ISO 68-1.Internal screw threads according to this part of ISO 965 are intended to mate with external screw threads with maximum size of tolerance position h before hot-dip galvanizing.The limits of sizes for the tolerance quality specified are derived from tolerances specified in ISO 965-1.The fundamental deviations for internal screw threads with a tolerance position AZ have been calculated according to the following formula:ElAZ = + (300 + 20P)whereEI is expressed in micrometres;P is expressed in millimetres.The fundamental deviations for internal screw threads with a tolerance position AX have been calculated according to the following formula:ElAX = + {220P - 20)whereEI is expressed in micrometres;P is expressed in millimetres.Products made with thread tolerances according to this part of ISO 965 may show load failure when tested in accordance with ISO 898-2 without adjustment of the other mechanical properties.Internal screw threads with thread tolerances according to this part of ISO 965 must not be mated with external screw threads having thread tolerances according to ISO 965-4 because such combinations will create severe risk of thread stripping.NOTE Internal screw threads with tolerance class 6AZ are primarily intended to mate with external screw threads centrifuged after hot-dip galvanizing.Internal screw threads with tolerance class 6AX are primarily intended to mate with hot-dip galvanized external screw threads with heavy coating not centrifuged.

ISO 965-5 AMD 1-2021ISO一般用途米制螺纹. 公差. 第5部分: 与镀锌前公差带位置为h大尺寸的热沉镀锌外螺纹相配的内螺纹的极限尺寸. 修改件1

\"Internal threads shall be tapped after the hot-dip galvanizing process has been completed, therefore no galvanizing coating is present on the surface of internal threads.\"

ISO 1085-2016螺钉和螺母的装配工具. 双头扳手. 对边尺寸组配

This document specifies the size pairing of double-ended wrenches with unequal nominal widths across flats. NOTE The wrenches covered by this document are those identified in ISO 1703:2005 under reference nos. 1 1 01 02 0, 1 1 02 03 0, 1 1 02 04 0, 1 1 02 05 0, 1 1 02 06 0, 1 1 02 08 0.