热塑性聚烯烃防水卷材检测

热塑性聚烯烃防水卷材检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB 27789-2011热塑性聚烯烃(TPO)防水卷材

本标准规定了热塑性聚烯烃防水卷材的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、贮存和运输。本标准适用于建筑工程用的以乙烯和α烯烃的聚合物为主要原料制成的防水卷材。

GB/T 35468-2017种植屋面用耐根穿刺防水卷材

本标准规定了种植屋面用耐根穿刺防水卷材的术语和定义、分类和标记、一般要求、技术要求、试验方法、检验规则及标志、包装、运输和贮存等。本标准适用于种植屋面用具有耐根穿刺性能的防水卷材，不适用于由不同类型的卷材复合而成的系统。

GB/T 35609-2017绿色产品评价 防水与密封材料

本标准规定了绿色建筑防水与密封材料的术语和定义、评价要求、评价方法。本标准适用于建筑防水卷材、防水涂料和密封胶的绿色产品评价。

GB 50681-2011机械工业厂房建筑设计规范

本规范适用于下列范围：1 新建、扩建、改建的机械工业厂房及其附属建筑的建筑设计；2 机械工业工厂中电离辐射室的建筑设计；3 机械工业工厂中电磁屏蔽室，屏蔽频率为0.15MHz～30MHz利用建筑物增设屏蔽层的建筑设计。

GB 50693-2011坡屋面工程技术规范

为提高我国坡屋面工程技术水平，确保工程质量，制定本规范。本规范适用于新建、扩建和改建的工业建筑、民用建筑坡屋面工程的设计、施工和质量验收。坡屋面工程的设计和施工应遵守有关环境保护、建筑节能和安全的规定，并应采取相应措施。 坡屋面工程应积极采用成熟的新材料、新技术、新工艺。坡屋面工程的设计、施工和质量验收除应符合本规范外，尚应符合现行有关标准的规定。

JC/T 974-2005道桥用改性沥青防水卷材

本标准规定了道桥用改性沥青防水卷材的分类、要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于以水泥混凝土为面层的道路和桥梁表面，并在其上面辅加沥青混凝土层的改性沥青聚酯胎防水卷材，其它用途如机场跑道、停车场也可参照使用。

JGJ 155-2013种植屋面工程技术规程

本规程适用于新建、既有建筑屋面和地下建筑顶板种植工程的设计、施工质量验收和维护管理。

JGJ/T 181-2009房屋建筑与市政基础设施工程检测分类标准

本标准适用于房屋建筑和市政基础设施工程检测的分类。

JGJ/T 200-2010喷涂聚脲防水工程技术规程

本规程适用于混凝土和砂浆表面喷涂聚脲防水工程的材料选择、设计、施工及验收。

JGJ/T 212-2010地下工程渗漏治理技术规程

本规程适用于地下工程渗漏的治理。

JGJ/T 316-2013单层防水卷材屋面工程技术规程

本规程适用于新建、扩建和改建的工业建筑、民用建筑采用单层防水卷材的屋面工程的设计、施工及质量验收。

DB11/ 366-2006种植屋面防水施工技术规程

根据北京市种植屋面发展的需要,为规范北京地区种植屋面防水施工及质量验收,防治种植屋面渗漏,确保种植屋面防水工程质量及使用功能,制定本规程。本规程适用于新建或旧屋面改造的种植屋面防水工程及地下建筑顶板覆土种植防水工程。

DIN EN 13707-2013防水柔性板材. 屋顶防水用增强沥青板. 特征和定义; 德文版本EN 13707-2013

This document specifies definitions and characteristics for flexible reinforced bitumen sheets for which the intended use is roofing. This covers sheets used as top layers, intermediate layers and underlayers. It does not cover reinforced bitumen sheets for waterproofing used as underlays for discontinuous roofing. It does not cover waterproofing sheets which are intended to be used fully bonded under bituminous products (e. g. asphalt) directly applied at high temperature.

DIN EN 13956-2013防水用柔性薄板.屋顶防水用塑料和橡胶薄板.定义和特征.德文版本EN 13956-2012

This European Standard specifies the definitions and characteristics of plastic and rubber sheets including sheets made out of their blends and alloys (thermoplastic rubber) for which the intended use is roof waterproofing. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.

DIN EN 13969-2007防水用柔性薄板.包括沥青底层制箱用薄板的沥青防潮薄板.定义和特性

This document specifies definitions and characteristics of flexible reinforced bitumen sheets for which the intended use is as damp proofing for buildings. including basement tanking.It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this standard.

DIN EN 14576-2005土工合成织物.测定聚合土工合成织物阻挡层抗环境应力断裂的试验方法

This document specifies a test method for screening the resistance of polymeric geosynthetic barriers to stress cracking. The test is applicable to polypropylene and polyethylene based products and to all other polymeric geosynthetic barriers which have a partially crystalline structure.

DIN EN 14909-2012防水弹性薄板.塑料和橡胶防水进程.定义和特征.德文版本EN 14909-2012

This European Standard specifies the characteristics of flexible sheets of plastics and rubber intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard. This European Standard does not cover related products such as preformed cavity trays, coping and flashings.

DIN EN 14967-2006防水用柔性薄板.沥青防潮层.定义和特征

This European Standard specifies the characteristics of flexible sheets of bitumen intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard. This European Standard does not cover related products such as preformed cavity trays coping and flashings. requirements for bitumen damp proof courses. The main addressed characteristics will be: water tightness, gas permeability, mechanical properties like the resistance to perforation or the impact resistance and the durability of those characteristics against chemical or biological agents and/or weathering.