复合铝箔聚乙烯绝热制品检测
GB/T 19686-2015建筑用岩棉绝热制品
本标准规定了建筑领域用岩棉绝热制品（以下简称岩棉制品）的适用范围、分类和标记、要求、试验方法、检验规则、标志、包装、运输及贮存。本标准适用于在建筑物围护结构上使用的岩棉制品，也适用于在具有保温功能的建筑构件和地板使用的岩棉制品。本标准不适用于外墙外保温薄抹灰系统使用的岩棉制品。
GB 50126-2008工业设备及管道绝热工程施工规范
本规范适用于新建、扩建和改建的外表面温度为-196～+850℃的工业设备及管道绝热工程的施工。本规范不适用于设备和管道的内隔热衬里和有特殊要求（核能辐射装置、航空工业、航天工业等）的设备和管道，以及埋地长输管道和临时设施的绝热工程的施工。工业设备及管道绝热工程的施工，应按设计文件及本规范的规定执行。当需要修改设计、材料代用或采用新材料时，必须经原设计单位同意。绝热工程的施工，除应执行本规范的规定外，尚应符合现行有关标准、规范的规定。
GB 50693-2011坡屋面工程技术规范
为提高我国坡屋面工程技术水平，确保工程质量，制定本规范。本规范适用于新建、扩建和改建的工业建筑、民用建筑坡屋面工程的设计、施工和质量验收。坡屋面工程的设计和施工应遵守有关环境保护、建筑节能和安全的规定，并应采取相应措施。 坡屋面工程应积极采用成熟的新材料、新技术、新工艺。坡屋面工程的设计、施工和质量验收除应符合本规范外，尚应符合现行有关标准的规定。
JC/T 2494-2018复合铝箔聚乙烯绝热制品
本标准规定了复合铝箔聚乙烯绝热制品的术语和定义、分类和标记、铝箔要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于使用温度为70℃至-30℃的用于热反射和防潮等用途的复合铝箔聚乙烯绝热制品。复合镀铝膜聚乙烯绝热制品可参照本标准。
SY/T 0324-2014直埋高温钢质管道保温技术规范
本规范适用于公称直径为50mm～1400mm，输送介质温度在120℃～350℃范围内，工作管压力不大于2. 5MPa的高温管道保温。
JGJ/T 316-2013单层防水卷材屋面工程技术规程
本规程适用于新建、扩建和改建的工业建筑、民用建筑采用单层防水卷材的屋面工程的设计、施工及质量验收。
DIN EN 14303-2016建筑设备和工业装置用隔热产品.工厂制矿物棉(MW)产品.规范;德文版本EN 14303-2015
for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately 0 °C to + 800 °C. Below an operating temperature of ambient, special means against water vapour diffusion and water accumulation by air flow might be required. Below an operating temperature of - 50 °C, special tests regarding the suitability of the products in the intended application are advised (e. g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured with or without facings or coatings, in the form of rolls, boards, slabs, mats, felts, quilts, wired mats, lamella mats, bevelled lags and pipe sections. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard. This European Standard does not cover products for in situ insulation (blowing or pouring) or products for the insulation of the building structure. This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.
