气凝胶检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 8718-2008炭素材料术语

本标准规定了炭素材料术语的分类规则，炭素材料的原料术语、产品术语、表观质量术语、化学分析和物理检测术语。本标准适用于编制各种标准、技术性文件、资料、编写和翻译手册、教材及书刊等。

GB/T 25996-2019绝热材料对奥氏体不锈钢外部应力腐蚀开裂的试验方法

本标准规定了绝热材料对奥氏体不锈钢外部应力腐蚀开裂的试验方法的术语和定义、仪器与设备、试剂与材料、不锈钢试件制备、绝热材料试样制备、试验方法、试验用敏化的不锈钢试件合格验证、试验后不锈钢试件检查、试验结果、试验报告。本标准适用于覆盖奥氏体不锈钢用绝热材料及其制品，主要包括矿物棉、硅酸钙、复合硅酸盐、膨胀珍珠岩、泡沫石棉、泡沫玻璃、气凝胶和保温防火涂料等。也适用于水泥和粘结剂。本标准给出了达纳法和滴注法两种测试方法，适用性如下：——达纳法仅适用于芯吸型材料，滴注法适用于所有可被切割或成型为试验试样的材料；——当材料可热处理成芯吸型材料时，可用达纳法或滴注法测试；——当材料无法处理成芯吸型材料或热处理温度大于厂家推荐温度时，用滴注法测试。

GB/T 34336-2017纳米孔气凝胶复合绝热制品

本标准规定了纳米孔气凝胶复合绝热制品(简称气凝胶制品)的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、运输及贮存。本标准适用于工业及建筑用纳米孔二氧化硅基气凝胶复合绝热制品。其他类型的气凝胶制品也可参考采用。

CECS 346-2013厚层腻子墙体隔热保温系统应用技术规程

本规程适用于除严寒地区以外各气候地区的新建、扩建、改建和节能改造的民用建筑和工业建筑墙体保温工程的设计、施工和验收。

JC/T 618-2019绝热材料中可溶出氯化物、氟化物、硅酸盐和钠离子的化学分析方法

本标准规定了绝热材料中可溶出氯化物、氟化物、硅酸盐、钠离子和浸出液pH测定的试验条件、试样制备、试液制备、空白试验、测定方法、精密度和试验报告。本标准适用于矿物棉及其制品、硅酸钙、复合硅酸盐、膨胀珍珠岩、泡沫石棉、泡沫玻璃、气凝胶绝热制品和保温防火涂料等覆盖奥氏体不锈钢用绝热材料的可溶出氯化物、氟化物、硅酸盐、钠离子和浸出液pH的测定，也适用于其他用途绝热材料的可溶出氯化物、氟化物、硅酸盐、钠离子和浸出液pH的测定。

JC/T 2518-2019疏水二氧化硅气凝胶粉体

本标准规定了疏水二氧化硅气凝胶粉体的术语和定义、分类和标记、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于溶胶-凝胶法制备的疏水型二氧化硅气凝胶粉体，不适用于气相法或沉淀法制备的白炭黑。

JC/T 2669-2022气凝胶中空玻璃

本文件规定了气凝胶中空玻璃的术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。本文件适用于建筑及保温隔热用气凝胶中空玻璃。

SY/T 0324-2014直埋高温钢质管道保温技术规范

本规范适用于公称直径为50mm～1400mm，输送介质温度在120℃～350℃范围内，工作管压力不大于2. 5MPa的高温管道保温。

JGJ 113-2015建筑玻璃应用技术规程

本规程适用于建筑玻璃的设计及安装。

HJ 2015-2012水污染治理工程技术导则

本标准规定了水污染治理工程在设计、施工、验收和运行维护中的通用技术要求。本标准为环境工程技术规范体系中的通用技术规范,适用于厂(站)式污(废)水处理工程。对于有相应的工艺技术规范或污染源控制技术规范的工程,应同时执行本标准和相应的工艺技术规范或污染源控制技术规范。本标准可作为水污染治理工程环境影响评价、设计、施工、竣工验收及运行维护的技术依据。

ASTM C168-2008有关隔热的标准术语

ASTM C168-2008a有关隔热的标准术语

ASTM C168-2008b有关隔热的标准术语

ASTM C168-2010隔热材料有关的标准术语

1.1 This standard provides definitions, symbols, units, and abbreviations of terms used in ASTM standards pertaining to thermal insulating materials, and to materials associated with them. 1.2 This terminology is not intended to be used to classify insulation materials as having particular properties. Rather, classification of insulation materials is to be done by the material standards themselves. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1728-2012柔性气凝胶绝热的标准规格

1.1 This specification covers the classification and performance of flexible aerogel thermal insulation. This will cover the range of continuous exposure operating temperatures from -321x00B0;F (-196x00B0;C) up to 1200x00B0; F (649x00B0;C). 1.2 For satisfactory performance, properly installed protective vapor retarders or barriers shall be used on below ambient temperature applications to reduce movement of moisture through or around the insulation to the colder surface. Failure to use a vapor retarder or barrier could lead to insulation and system non-performance. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1728-2013柔性气凝胶绝热的标准规格

1.1x00a0;This specification covers the classification and performance of flexible aerogel thermal insulation. This will cover the range of continuous exposure operating temperatures from -321x00b0;F (-196x00b0;C) up to 1200x00b0; F (649x00b0;C). 1.2x00a0;For satisfactory performance, properly installed protective vapor retarders or barriers shall be used on below ambient temperature applications to reduce movement of moisture through or around the insulation to the colder surface. Failure to use a vapor retarder or barrier could lead to insulation and system non-performance. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4x00a0;The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1728-2017挠性气凝胶绝缘的标准规格

1.1x00a0;This specification covers the classification and performance of flexible aerogel thermal insulation. This will cover the range of continuous exposure operating temperatures from x2013;321x00b0;F (x2013;196x00b0;C) up to 1200x00b0;F (649x00b0;C). 1.2x00a0;For satisfactory performance, properly installed protective vapor retarders or barriers shall be used on below ambient temperature applications to reduce movement of moisture through or around the insulation to the colder surface. Failure to use a vapor retarder or barrier could lead to insulation and system non-performance. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4x00a0;The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.