人造矿物纤维保温材料检测
GB/T 51232-2016装配式钢结构建筑技术标准
本标准适用于抗震设防烈度为6度到9度的装配式钢结构建筑的设计、生产运输、施工安装、质量验收与使用维护。
GBZ/T 211-2008建筑行业职业病危害预防控制规范
本标准规定了建筑行业职业病危害预防控制的基本要求、职业病危害因素的识别、防护措施及应急救援等要求。本标准适用于从事土木工程、建筑工程、线路管道和设备安装工程及装修工程的新建、扩建、改建和拆除等施工活动的企业、事业及个体经济组织的职业病危害预防控制及卫生行政部门、建设主管部门和项目监理对施工企业的职业卫生监管。
CECS 445-2016非金属面结构保温夹芯板设计规程
本规程适用于工业与民用建筑采用的围护结构、轻型屋面、吊顶板等用的非金属面结构保温夹芯板的设计。
JGJ/T 229-2010民用建筑绿色设计规范
本标准适用于新建、改建和扩建民用建筑的绿色设计。
CNS 3657-2017人造矿物纤维保温材料
本标准适用于人造矿物纤维之保温材料，且其制造原料不得含有石棉。
ASTM C1338-2014测量隔热材料和饰面耐霉性的标准试验方法
2.1x00a0;The type of materials used in the manufacture of insulation products and the type of membrane used to face these products can sometimes affect fungi sustenance in the presence of high humidity. 2.2x00a0;This test method is used to determine the relative ability of an insulation and its facing to resist fungal growth under conditions favorable for their development. 2.3x00a0;This test method uses a comparative material to determine the relative ability of a material to resist fungal growth. In some specialized product areas, it is required that no growth take place. In such cases, the use of the comparative material is omitted and the pass/fail criterion is based upon growth. 1.1x00a0;This test method covers the determination of the ability of new insulation materials and their facings to resist fungal growth. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
ASTM C1393-2000a(2006)管子和容器用垂直向矿物纤维薄板卷和薄板热绝缘的标准规范
1.1 This specification covers the composition, dimensions, and physical properties of compression-resistant, perpendicularly oriented mineral fiber (rock, slag, or glass) roll and sheet insulation intended for use on flat, curved, or round surfaces up to 1000176;F (538176;C). This product (pipe and tank insulation) is typically used on nominal 24 in. (610 mm) or greater diameter surfaces. For specific applications, the actual use temperatures and diameters shall be agreed upon between the manufacturer and the purchaser.1.2 The orientation of the fibers within the roll or sheet insulation is essentially perpendicular to the heated/cooled surface (parallel to heat flow). This specification does not apply to flat block, board, duct wrap, or preformed pipe mineral fiber insulation where the insulation fiber orientation is generally parallel to the heated/cooled surface (across the heat flow).1.3 For satisfactory performance, properly installed protective vapor retarders must be used in low-temperature (below ambient) applications to prevent movement of water vapor through or around the insulation towards the colder surface.1.4 The values stated in inch-pound units are to be regarded as standard. The SI equivalents of inch-pound units are given in parentheses for information only and may be approximate.1.5 When the installation or use of thermal materials, accessories, and systems may pose safety or health problems, the manufacturer shall provide the user-appropriate current information regarding any known problems associated with the recommended use of the company's products and shall also recommend protective measures to be employed in their safe utilization. The user shall establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
EN 14015-2004在室温及高于环境温度液体储存用平底,立式,圆柱形,现场建造的地面上可焊钢罐的设计和制造规范
This document specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached (see Annex A).
NF P84-207-1-2-2008建筑工程.带防水涂层的承重木材和木制板屋顶.第1-2部分:材料选择的通用标准(GCM)
Le présent document définit les critères de choix des matériaux à utiliser pour l'exécution de l'étanchéité de toitures de bâtiments comportant des éléments porteurs en bois ou panneaux dérivés du bois, faisant l'objet de la norme NF DTU 43.4 P1-1 Travaux de bâtiment - Toitures en éléments porteurs en bois et panneaux dérivés du bois avec revêtements d'étanchéité - Partie 1-1 : Cahier des clauses techniques types.
DIN 4102-4-2016建筑材料和建筑构件的耐火性能.概要和分级的建筑材料、构件和特种构件的应用
This document contains catagorized results of fire tests of buildings materials, components and construction types. Due to the assignment to the classes of building materials according to DIN 4102 part 1 and the fire resistance classes of the other parts of DIN 4102 respectively, further fire tests for the verification of usability required by the building regulations are not necessary.
DIN 4109-33-2016建筑物隔声. 第33部分: 隔声验证使用数据 (组件目录). 木结构, 轻型结构和干墙
This standard contains sound insulation specifications of components and structures for timber construction, lightweight construction and dry walling, which may be used without acoustic testing in the calculation procedures stated in DIN 4109-2 for the verification of the requirements of DIN 4109-1.
BS EN 14015-2004在室温和高于室温下液体储存用现场建造的立式、圆柱形、平底、地上用焊接钢罐的设计和制造规范
1 This document specifies the requirements for the materials, design, fabrication, erection, testing and inspection of site built, vertical, cylindrical, flat bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperatures and above, and the technical agreements that need to be reached (see Annex A).\nThis document does not apply to tanks where the product is refrigerated to maintain it as a liquid at atmospheric pressure (see prEN 14620).\nThis document is concerned with the structural integrity of the basic tank structure and does not provide requirements for considering process design, operational issues, safety and firefighting facilities, in-service inspection, maintenance or repair. These aspects are covered in detail in other Codes of Practice (see Annex B).\n2 This document applies to closed-top tanks, with and without internal floating covers (see Annex C) and open-top tanks, with and without floating roofs (see Annexes D and E). It does not apply to 'lift-type' gas holders.\n3 This document applies to storage tanks with the following characteristics:\na) design pressure less than 500 mbar
