发光二极管模块的直流或交流电源电子控制装置检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 778.2-2018饮用冷水水表和热水水表第2部分:试验方法

GB/T 778的本部分规定了完整水表和作为独立单元的水表测量传感器(包括流量或体积检测元件)以及计算器(包括指示装置)的试验要求。本部分适用于GB/T 778.1定义的饮用冷水水表和热水水表的型式评价试验和首次检定试验。本部分给出了水表型式评价试验和首次检定试验的详细试验程序、试验原则、试验设备和试验方法。如果法规有要求，本部分也适用于辅助装置。

GB/T 19436.1-2013机械电气安全电敏保护设备第1部分:一般要求和试验

GB/T 19436的本部分规定了作为安全相关系统的组成部分专门用于检测人体的非接触型电敏保护设备(ESPE)的设计、制造和试验的一般要求。需要特别注意的是针对其功能和设计要求,要确保达到适宜的安全相关性能。电敏保护设备(ESPE)可以包括可选择的安全相关功能,这些要求在附录A中给出。敏感功能的具体类型的特殊要求,在GB/T 19436其他部分给出。本部分没有规定检测区的尺寸或形状以及它在任何特殊应用中涉及危险的布置,也没有规定由什么构成任何机械的危险状态,只限于ESPE的功能及其怎样与机械连接。当数据接口用于控制可选择的ESPE的安全相关功能时(附录A),本部分没有规定特殊的要求。对于这些安全相关功能的要求,可以通过查阅其他标准(如GB/T 16855.1、IEC 61508、IEC/TS 62046和IEC 62061)来确定。本部分可能与那些对非人体保护的应用有关,例如,保护机械或产品免于机械损坏。在这些应用中,可能需要附加的要求,例如必须由敏感功能辨认的材料,具有不同于人的一些特性。本部分不涉及电磁兼容性(EMC)的发射要求。

GB 19510.14-2009灯的控制装置第14部分:LED模块用直流或交流电子控制装置的特殊要求

本部分规定了使用250V以下直流电源和1000V以下、50H<下标z>或60H<下标z>交流电源的LED模块用电子控制装置的特殊安全要求,该电子控制装置的输出频率不同于电源频率。本部分中规定的LED模块控制装置是设计在安全特低电压或等效安全特低电压或更高的电压下能够为LED模块提供恒定的电压或电流的控制装置。非纯电压源和电流源类型控制装置也包括在本部分之内。

GB/T 22663-2008工业机械电气设备.电磁兼容.机床抗扰度要求

本标准规定了用于工业环境或类似用途，线间额定电压不超过1000Va.c或者1500Vd.c的机床电磁兼容的抗扰度要求。本抗扰度标准也可用于评估在其他环境中使用的机床，这些环境（住宅、轻工业环境等）比工业环境要求的抗扰度水平低。本标准不适用于安装在特殊的电磁环境中的机床，例如：存在强电磁场（如在广播发射台附近），或在有电力网强脉冲环境（如发电站）的机床。在这些场合中使用的设备及系统，需采取相应的降低电磁影响的措施。本标准涉及电磁抗扰度的频率范围为0Hz至400GHz。其他频率不在标准考虑之列。

GB 51043-2014电子会议系统工程施工与质量验收规范

本规范适用于新建、扩建、改建电子会议系统工程的施工和质量验收。

SH/T 3038-2017石油化工装置电力设计规范

本规范规定了石油化工装置电力设计应遵循的主要设计原则。本规范适用于新建、改建或扩建的石油化工企业生产装置(包括炼油、化工、煤化工，以下简称生产装置)的电力设计。

NB/T 20433-2017核电厂气态排出流(放射性)活度连续监测设备要求

本标准规定了核电厂气态排出流(放射性)活度连续监测设备的技术要求。本标准适用于核电厂正常运行和预计运行事件下气态排出流放射性气溶胶监测设备、放射性碘监测设备和放射性惰性气体监测设备，不适用于核电厂事故及事故后辐射监测设备。本标准不涉及氚和C-14监测设备的相关技术要求。

TZ 206-2007客货共线铁路信号工程施工技术指南

本技术指南适用于设计速度等于或小于200 km/h的客货共线标准轨距铁路信号工程的施工。

DL/T 774-2015火力发电厂热工自动化系统检修运行维护规程

本标准规定了火力发电厂热控系统检修运行维护的内容、方法和技术管理应达到的标准。本标准适用于火力发电厂已投产机组热控系统的检修和日常运行维护工作。

IEC 62384-2020发光二极管(LED)模块用直流或交流电源电子控制装置. 性能要求

This document specifies performance requirements for electronic controlgear for use on DC or AC supplies up to 1000 V (alternating current at 50 Hz or 60 Hz) and with an output frequency which can deviate from the supply frequency, associated with LED modules according to IEC 62031. Controlgear for LED modules specified in this document are designed to provide constant voltage or current. Deviations from the pure voltage and current types do not exclude the gear from this document. NOTE 1 The tests in this document are type tests. Requirements for testing individual controlgear during production are not included. NOTE 2 Requirements for controlgear which incorporate means for varying the output power are under consideration. NOTE 3 It can be expected that controlgear complying with this document will ensure satisfactory operation between 92 % and 106 % of the rated supply voltage, taking into account the specifications of the LED module manufacturer.

UL 399-2008饮用水冷却器

1.1 These requirements cover self-contained drinking-water coolers which employ hermetic refrigerantmotor-compressors and which are designed for connection to alternating-current circuits rated not greaterthan 600 volts in accordance with the National Electrical Code, NFPA 70. The requirements also apply towater coolers which supply both hot and cold water.1.2 These requirements do not include additional requirements applicable to equipment designed for usein hazardous locations as defined in the National Electrical Code, NFPA 70.1.3 A product that contains features, characteristics, components, materials, or systems new or differentfrom those covered by the requirements in this standard, and that involves a risk of fire, electric shock, orinjury to persons shall be evaluated using the appropriate additional component and end-productrequirements as determined necessary to maintain the acceptable level of safety as originally anticipatedby the intent of this standard. A product whose features, characteristics, components, materials, orsystems conflict with specific requirements or provisions of this standard cannot be judged to comply withthis standard. Where considered appropriate, revision of requirements shall be proposed and adopted inconformance with the methods employed for development, revision, and implementation of this standard.

UL 61496-1-2002电敏保护设备.第1部分:一般要求和试验

This part of IEC 61496 specifies general requirements for the design，construction and testing of ELECTRO—SENSITIVE PROTECTIVE EQUIPMENT(ESPE)for the safeguarding of machinery Special attention is di rected tofunctional and design requirements that ensure an appropriate safety related performance is achieved AnESPE may include optional safety-related functions，the requirements for which are given in annex AThe particular requirements for specific types of sensing function are given in other parts of this standardThis standard does not specify the dimensions or configuration of the DETECTION ZONE and its disposition inrelation to hazards in any particular application，nor what constitutes a hazardous state of any machineIt is restricted to the functioning of the ESPE and how it inte rfaces with the machineThis standard may be relevant to applications other than those for the protection of persons，for examplefor the protection of machinery or products frOm mechanical damage In those applications additionalrequirements may be necessary，for example when the materials that have to be recognized by thesensing function have different propedies from those of personsThis standard does not deal with electromagnetic compatibility(EMC)emission requirementsThis part of IEC 61496 provides general requirements for ESPES of various types employing differentmethods of sensing The particular requirements for specific types of sensing function will be covered insubsequent parts of this standa~The requirements for ESPES using active opto—electric protective devices，e g light curtains a re contained in part 2This pa rt refers to the technical suitability of the electro—sensitive protective equipment Its application mayrequire the use of substances and／or test procedures that could be inju rious to health unless adequateprecautions were taken Conformance with this standard in no way absolves either the SUPPLIER or the userfmm statutory obligations relating to the safety and health of persons du ring the use of the equipmentcovered by this standard

DIN EN 62703-2014液体介质中荧光氧分析仪的性能表示 (IEC 62703-2013); 德文版本EN 62703-2013

This standard is applicable to fluorometric oxygen analyzers used for the continuous determination of dissolved oxygen partial pressure or concentration. It applies to fluorometric oxygen analyzers suitable for use in water containing liquids, ultrapure waters, fresh or potable water, sea water or other aqueous solutions, industrial or municipal waste water from water bodies (e. g. lakes, rivers, estuaries) as well as for industrial process streams and process liquids.