混凝土制品脱模剂检测

GB/T 29423-2012用于耐腐蚀水泥制品的碱矿渣粉煤灰混凝土

本标准规定了用于耐腐蚀水泥制品的碱矿渣粉煤灰混凝土(以下简称碱矿渣粉煤灰混凝土)的术语和定义、分类、原材料、技术要求、试验方法、检验规则、贮存与输送等内容。本标准适用于处于酸、碱、盐环境下耐腐蚀水泥制品使用的碱矿渣粉煤灰混凝土。

GB 50990-2014加气混凝土工厂设计规范

本规范适用于新建、扩建和改建的蒸压加气混凝土工厂项目的设计。

JC/T 949-2021混凝土制品用脱模剂

本文件规定了混凝土制品用脱模剂(以下简称脱模剂)的术语和定义、分类和标记、一般要求、技术要求、试验方法、检验规则以及包装、出厂、运输和贮存。本文件适用于非纯油类物质的混凝土制品用脱模剂。

JC/T 2126.1-2012水泥制品工艺技术规程 第1部分：混凝土与钢筋混凝土排水管

本部分规定了混凝土和钢筋混凝土排水管(以下简称为排水管)产品制造过程中的原材料、生产工艺、质量控制以及标志、贮存和运输等。本部分适用于制造符合GB/T 11836及JC/T 640的钢筋混凝土排水管和顶进施工法用钢筋混凝土排水管。

JC/T 2126.5-2012水泥制品工艺技术规程 第5部分：环形混凝土电杆

本部分规定了环形混凝土电杆生产用原材料、生产工艺以及运输和贮存等技术要求。本部分适用于按GB/T4623生产的环形预应力混凝土电杆、环形部分预应力混凝土电杆和环形钢筋混凝土电杆。

JC/T 2126.6-2012水泥制品工艺技术规程 第6部分：先张法预应力混凝土管桩

本部分规定了先张法预应力混凝土管桩生产用原材料、生产工艺、检验、标志、运输和贮存以及产品合格证等。本部分适用于按GB 13476-2009制造的先张法预应力混凝土管桩(以下简称管桩)。其他离心成型的先张法预应力混凝土桩可参照执行。

JC/T 2351-2016预制混凝土衬砌管片安全生产规范

本标准规定了预制混凝土衬砌管片的安全基础管理、设备及安全设施、工艺安全规定、作业场所与职业健康安全等安全生产要求。本标准适用于预制混凝土衬砌管片的安全生产管理，其他混凝土制品生产可参照执行。

JTS 167-8-2013水运工程先张法预应力高强潘凝土管桩设计与施工规程

本规程适用于水运工程先张法预应力高强混凝土管桩的设计与施工。

SD 149-1985环形预应力混凝土电杆制造工艺规程(离心成型)

本工艺规程是为贯彻GB 4623-1984《环形预应力混凝土电杆》标准及我部架空电力线路的具体要求而制定的(变电架构也可参照执行)。凡本规程中未作规定的部分,应按有关规范或标准执行。凡采用新技术、新工艺、新材料、新设备时,应通过试验和验证后方可使用。

JGJ/T 416-2017建筑用真空绝热板应用技术规程

本规程适用于民用建筑中采用建筑用真空绝热板的建筑节能工程的设计、施工及验收。

TB/T 3433-2016高速铁路预制先张法预应力混凝土简支梁

本标准规定了新建高速铁路预制先张法预应力混凝土简支梁的技术要求、检验方法、检验规则、标志与制造技术证明书、保管及运输和架设。本标准适用于新建高速铁路预制先张法预应力混凝土简支梁（以下简称先张梁）。

EN 12629-3-2002制作混凝土和硅酸钙结构产品的机械的安全性.第3部分:滑动和转台机械

This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to machines for the manufacture of constructional products of calcium-silicate or concrete, where the mould(s) is(are) mounted on a turning or slide table. The motive power for compressing the mixture is effected either mechanically (Annexes A, B), or hydraulically (Annexes C and D). EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium-silicate.This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers.This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1 of annexes A, B, C, D) and the point where the pallets for concrete products are brought to the assembly (see point 8 at annexes C and D) until the point where the green products are removed from the machine to the curing system (see point 2 of annexes A, B, C, D).This European Standard deals with the hazards listed in Clause 4 which can arise during the operation and maintenance, including the interfaces, of the slide and turntable machines, when carried out in accordance with the specifications given by the manufacturer or his authorised representative.This standard establishes safety requirements and/or methods of protection which apply to these machines.This document is not applicable to side and turntable machines, which are manufactured before the date of publication of this document by CEN.

EN 13670-2009混凝土结构实现［代替:CEN ENV 13670-1］

This European Standard gives common requirements for execution of concrete structures, it applies to both in-situ works and construction using prefabricated concrete elements. (2)This standard expects the execution specification to state all the specific requirements relevant to the particular structure. (3)This standard is applicable to permanent as well as temporary concrete structures. (4) Additional or different requirements should be considered and, if required, given in the execution specification when using: a) lightweight aggregate concrete; b) other materials (e. g. fibres) or constituent materials; c) special technologies/innovative designs. (5)This standard does not apply to concrete members used only as equipment or construction aids for the execution. (6)This standard does not cover the specification, production and conformity of concrete. (7)This standard is not applicable to the production of precast concrete elements made in accordance with product standards. (8)This standard does not cover safety and health aspects of execution, or third party safety requirements. (9)This standard does not cover contractual issues or responsibilities for the identified actions. NOTE It is within the concept of this standard that supplementing requirements can be given for the individual project in the execution specification, on a national level in a national annex, or on a general basis in European standards for special applications e. g. standards for special geotechnical works.

NF P19-220-2008预制混凝土制品.树脂粘接混凝土.要求和试验方法

La présente Norme européenne spécifie les prescriptions communes pour le béton de résine utilisé dans la fabrication de produits préfabriqués en béton. Elle est destinée à être utilisée lors de l'élaboration de documents relatifs aux produits en béton de résine.Les normes de produits en béton de résine définiront des prescriptions particulières pouvant être complémentaires à celles données dans le présent document. Les normes de produits prescriront des valeurs limites pour certaines caractéristiques.Ci-après, quelques exemples d'utilisation du béton de résine: mobilier urbain et de jardin, éléments décoratifs, appuis de fenêtre, bâtis de machines-outils, éléments de clôtures, mangeoires et caillebotis pour le bétail, etc.La présente norme n'est pas applicable aux bétons et aux mortiers à liant mixte résine/ciment ainsi qu'aux bétons et mortiers imprégnés de polymère à l'état durci (elle s'applique donc uniquement aux PC, et non aux PCC ou SPCC).

DIN EN 12629-3-2011混凝土和硅酸钙结构产品生产设备.安全性.第3部分:滑式和转盘机;德文版本EN 12629-3-2002+A1-2010

This part of EN 12629, taken together with EN 12629-1-2000+A1-2010, applies to machines for the manufacture of constructional products of calcium-silicate or concrete, where the mould(s) is (are) mounted on a turning or slide table. The motive power for compressing the mixture is effected either mechanically (Annexes A,B),or hydraulically(Annexes C and D).

DIN-Fachbericht CEN/TR 15177-2006混凝土耐冻裂试验.内部结构破坏

This document specifies three test methods for the estimation of the freeze-thaw resistance of concrete with regard to internal structural damage. It can be used either to compare new constituents or new concrete compositions against a constituent or a concrete composition that is known to give adequate performance in the local environment or to assess the test results against some absolute numerical values based on local experiences.Extrapolation of test results to assess different concrete i.e. new constituents or new concrete compositions requires an expert evaluation. NOTE Specification based on these test methods should take into account the behaviour of concrete under practical conditions. There is no established correlation between the results obtained by the three test methods. All tests will clearly identify poor and good behaviour, but they differ in their assessment of marginal behaviour.

DIN-Fachbericht CEN/TR 15678-2008混凝土.地下水和地表水进入土壤的受控有害物质的释放.新的或未认可的混凝土组成成分和生产混凝土用试验方法

This Technical Report describes test methods, that when completed, will produce eluates for the assessment of inorganic and organic substances potentially released from either the constituents of concretes (tested within hardened reference concretes) or from production concretes (or test pieces representative of production concretes) whether presented in the pre-hardened/precast state, fresh wet state or pre-packaged.

BS EN 12629-3-2002+A1-2010生产混凝土和硅酸钙结构件的设备.安全性.滑动和绞盘机

1.1 This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to machines for themanufacture of constructional products of calcium-silicate or concrete, where the mould(s) is(are) mounted on aturning or slide table. The motive power for compressing the mixture is effected either mechanically (Annexes A,B), or hydraulically (Annexes C and D).EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture ofconstructional products from concrete and calcium–silicate.This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010specific to the machines it covers.1.2 !This European Standard deals with all significant hazards pertinent to these machines, when they areused as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (seeClause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risksarising from the significant hazards.1.3 This European Standard applies to the machines from the point at which the mixture enters the machine (seepoint 1 of annexes A, B, C, D) and the point where the pallets for concrete products are brought to the assembly(see point 8 at annexes C and D) until the point where the green products are removed from the machine to thecuring system (see point 2 of annexes A, B, C, D).1.4 This European Standard deals with the hazards listed in Clause 4 which can arise during the operation andmaintenance, including the interfaces, of the slide and turntable machines, when carried out in accordance with the specifications given by the manufacturer or his authorised representative.This standard establishes safety requirements and/or methods of protection which apply to these machines."1.5 This document is not applicable to side and turntable machines, which are manufactured before the date ofpublication of this document by CEN.

BS EN 13670-2009混凝土结构实现

(1) This European Standard gives common requirements for execution of concrete structures, it applies toboth in-situ works and construction using prefabricated concrete elements.(2) This standard expects the execution specification to state all the specific requirements relevant to theparticular structure.(3) This standard is applicable to permanent as well as temporary concrete structures.