海上和有关结构防护漆检测

海上和有关结构防护漆检测项目报价？  解决方案？  检测周期？  样品要求？

点 击 解 答

GB/T 37443-2019海洋平台起重机一般要求

本标准规定了海洋平台起重机(以下简称起重机)的载荷和载荷组合、结构及组成、机构、主要零部件、驱动和控制系统、人员起吊、安全装置、涂装、试验、标志和标牌等一般要求。本标准适用于海洋平台起重机的设计、制造和验收。本标准不适用于波浪补偿等特殊型式的起重机及吊架和/或紧急逃生装置。

HG/T 3792-2014交联型氟树脂涂料

本标准规定了交联型氟树脂涂料产品的产品分类，要求，试验方法，检验规则，标志、包装和贮存等内容。本标准适用于以含反应性官能团的氟树脂为主要成膜物并加入颜填料(清漆不加)、溶剂、助剂等辅料作为主剂，以脂肪族多异氰酸酯树脂为同化剂的双组分常温固化型建筑外墙、混凝土表面和金属表面用面漆。本标准还适用于以含反应性官能团的氟树脂为主要成膜物，以氨基树脂或封闭型脂肪族多异氰酸酯树脂为交联剂，并加入颜填料(清漆不加)、溶剂、助剂等辅料制成的单组分烘烤同化型金属表面用面漆。用于其他基材表面的交联型氟树脂涂料也可参考本标准。

TS EN ISO 12944-9-2018色漆和清漆. 防护漆体系对钢结构的腐蚀防护. 第9部分: 海上建筑及相关结构用防护涂料体系和实验室性能测试方法(ISO 12944-9:2018)

This document specifies the performance requirements for protective paint systems for offshore and related structures (i.e. those exposed to the marine atmosphere, as well as those immersed in sea or brackish water).

DIN 50929-1-2017金属腐蚀.承受外部腐蚀时金属材料腐蚀的可能性.第1部分:总则

The definitions described in this standard indicate the rating of corrosion probability of metallic materials in a corrosive media which contains an aqueous electrolyte which affect permanently or from time to time the surface of a component. It could be installation parts in buildings or containers, tubes and construction parts outside of buildings which are exposed to corrosion of soil, ground and surface water.

DIN EN 10339-2007陆上和海上输水管道用钢管. 防腐蚀用液体内壁环氧衬里

This European Standard specifies the requirements for the application of liquid applied epoxy internal linings,for the corrosion protection of steeltubes.This type oflining is generally used in the transport and distribution,under pressure or by gravity,of water intended for human consumption and industrial use,sea water,waste water and also in fire water.The temperature of the water transported generally does not exceed 50℃.The choice of the lining and its limits of use depend on the type of product used,the pipe laying conditions,the temperature and the chemical composition of the fluid.The choice of the product for the medium to be transported and its qualification are not part of this European Standard.The lining consists normally of one layer of liquid product,applied by spray airless technique after surface preparation.All or some of the requirements of this European Standard can apply to the internal linings of fittings,if agreedby the purchaser and the coater.The lining in this European Standard can be applied to longitudinally or spirally welded tubes and to seamless steel tubes used for the construction of pipelines for conveying liquids.This European Standard does not cover in-situ applied or rehabilitation linings.The constituent materials of epoxy linings,when used under the conditions for which they are designed,in permanentor temporary contct with water intended for human consumption,should not change the quality of that water to such an extent that it fails to comply with the requirements of European regulations at the end user.For this purpose,reference should be made to the relevant national standards transposing EN stsndards when available,dealing with the influence of materials on water quality.

DIN EN 12007-3-2015燃气供应系统.大使用压力小于等于16bar的管道.第3部分:钢专用功能要求;德文版本EN 12007-3-2015

This European Standard describes the specific functional requirements for steel pipelines in addition to the general functional requirements of EN 12007-1 for maximum operating pressures up to and including 16 bar.

DIN EN 16222-2012船体阴极保护.德文版本EN 16222-2012

This European Standard defines the general criteria and recommendations for cathodic protection of immersed external ship hulls and appurtenances.This European Standard does not cover safety and environmental protection aspects associated with cathodic protection. Relevant national or international regulations and classification society requirements apply.

DIN EN ISO 16961-2015石油, 石化和天然气工业. 钢制储罐的内部涂层和内衬 (ISO 16961-2015); 英文版本EN ISO 16961-2015

This International Standard specifies the minimum requirements for surface preparation, materials, application, inspection and testing of internal coating lining systems that are intended to be applied on internal surfaces of steel storage tanks of crude oil, hydrocarbons and water for corrosion protection. It covers both new construction and maintenance works of tank internal coating and lining as well as the repair of defective and deteriorated system. This International Standard also provides the minimum requirements for shop performance testing of the coated/lined samples and the criteria for their approval.

DIN EN ISO 21457-2010石油,石化和天然气工业.油和气体产品系统的材料选择和腐蚀控制(ISO 21457-2010).德文版本EN ISO 21457-2010

This International Standard identifies the corrosion mechanisms and parameters for evaluation when performing selection of materials for pipelines, piping and equipment related to transport and processing of hydrocarbon production, including utility and injection systems. This includes all equipment from and including the well head, to and including pipelines for stabilized products. This International Standard is not applicable to downhole components. Guidance is given for the following: corrosion evaluations; materials selection for specific applications, or systems, or both; performance limitations for specific materials; corrosion control. This International Standard refers to materials that are generally available, with properties that are known and documented. It also allows other materials to be evaluated and qualified for use. This International Standard does not provide detailed material requirements or guidelines for manufacturing and testing of equipment. Such information can be found in particular product and manufacturing standards.

BS EN ISO 21457-2010石油,石化和天然气工业.油和气体产品系统的材料选择和腐蚀控制

This International Standard identifies the corrosion mechanisms and parameters for evaluation whenperforming selection of materials for pipelines, piping and equipment related to transport and processing ofhydrocarbon production, including utility and injection systems. This includes all equipment from and includingthe well head, to and including pipelines for stabilized products. This International Standard is not applicableto downhole components.Guidance is given for the following:- corrosion evaluations;- materials selection for specific applications, or systems, or both;- performance limitations for specific materials;- corrosion control.This International Standard refers to materials that are generally available, with properties that are known anddocumented. It also allows other materials to be evaluated and qualified for use.This International Standard does not provide detailed material requirements or guidelines for manufacturingand testing of equipment. Such information can be found in particular product and manufacturing standards.