1001kV交流系统用静电防护服装检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 1001.1-2021标称电压高于1 000 V的架空线路绝缘子第1部分:交流系统用瓷或玻璃绝缘子元件定义、试验方法和判定准则

本文件界定了架空线路用瓷或玻璃绝缘子元件(以下简称绝缘子)的术语和特性，规定了检验特性规定值的条件、试验方法和判定准则。本文件适用于标称电压高于1 000 V、频率不超过100 Hz交流架空电力和牵引线路用瓷和玻璃绝缘子，以及直流架空电力牵引线路用绝缘子的定义、试验方法和判定准则。本文件也适用于绝缘子串元件、架空线路刚性绝缘子和变电所用的类似结构的绝缘子的定义、试验方法和判定准则。本文件不适用于构成电气部件的绝缘子，或电气结构中的部件，以及GB/T 8287(所有部分)中所包括的支柱绝缘子的定义、试验方法和判定准则。绝缘子串和绝缘子组的试验方法(如，湿操作冲击电压)和接收准则在GB/T 1001.2—2010中论述。本文件不包括有关按特定运行条件选择绝缘子的要求。绝缘子的特性值在相应的产品标准中规定。

GB/T 1001.2-2010标准电压高于1000V的架空线路绝缘子第2部分：交流系统用绝缘子串及绝缘子串组定义、试验方法和接收准则

GB/T 1001的本部分规定了标准电气试验程序及接收规则，以检验本部分范围内的绝缘子串和绝缘子串组的规定特性。本部分适用于标准电压高于1000V、频率不大于100Hz的架空电力线路用瓷或玻璃绝缘子串元件组成的绝缘子串和绝缘子串组。本部分也适用于直流架空牵引线路用的绝缘子串和绝缘子串组。本部分还适用于变电所用的类似结构的绝缘子串和绝缘子串组。本部分还可作为直流架空电力线路用的绝缘子串和绝缘子串组及复合绝缘子的暂用标准。

QJ 10013-2008氢氧火箭发动机试验系统安全规定

本标准规定了氢氧火箭发动机试验系统的安全要求及应急处理。本标准适用于氢氧火箭发动机(以下简称发动机)及组件地面试验，火箭氢氧子级动力系统试验系统可参照执行。

TB 10010-2016铁路给水排水设计规范

本规范适用于新建、改建铁路给水排水工程设计。

TB 10016-2016铁路工程节能设计规范

本规范适用于新建、改建铁路工程设计。

TB 10018-2018铁路工程地质原位测试规程

本规程适用于新建与改建铁路勘察设计、施工、运营等阶段的工程地质原位测试工作。

JB/T 10017-2012带表卡规

本标准规定了带表卡规的术语和定义、型式与基本参数、要求、试验方法、检查条件、检查方法、标志与包装等。本标准适用于测量范围上限不大于400mm，分度值为0.005mm、0.01mm、0.02mm、0.05mm、0.1mm的指针式带表卡和分辨力为0.005mm、0.01mm、0.02mm的数显带表卡规（统称为“带表卡规”）。

DL/T 1001-2006复合绝缘高压穿墙套管技术条件

本标准规定了复合绝缘高压穿墙套管的技术要求、试验方法、检验规则以及标志、包装、运输及储存。本标准适用于标称电压35kV及以上电压等级、频率为50Hz～60Hz的交流系统电站和变电所配电装置用的户外—户内电容式复合绝缘穿墙套管（以下简称套管）。安装地点的海拔为1000m以下，环境温度为-40℃～+40℃。

ASTM F1001-1999a防护服装材料评估用化学试剂的选择

1.1 The purpose of this guide is to provide a recommended list of both liquid and gaseous chemicals for evaluating protective clothing materials in testing programs. 1.2 Results derived from testing programs using these lists of challenge chemicals are not intended for the definitive characterization of protective clothing materials. 1.3 This list of challenge chemicals is not inclusive of all chemical challenges; the chemicals were chosen to represent broad ranges of liquid and gaseous chemical classes and properties. Not all chemical classes are represented. Other chemicals, especially those of interest to the manufacturer or user, should be tested in addition to those recommended in this guide. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific hazards statement is given in Section 7.

ASTM F1001-1999a(2006)防护服装材料评估用化学试剂的选择标准指南

This guide establishes a recommended list of challenge chemicals to encourage those who evaluate chemical protective clothing to test a minimum number of chemicals in common. This list will simplify the comparison of data from different sources. This guide may also serve material developers or evaluators in screening candidate protective clothing materials. Test methods applicable to the use of this guide include, but are not limited to, Test Methods F 903 and F 739. 5.3.1 The battery of chemical gases shall not be used for testing material penetration resistance because Test Method F 903 has been designed for measuring liquid penetration only. 5.3.2 Evaluation of materials against the gaseous chemical battery is primarily intended for those materials used in the construction of totally-encapsulating protective suits or other clothing items that are designed to prevent exposure to chemical vapors or gases. 1.1 The purpose of this guide is to provide a recommended list of both liquid and gaseous chemicals for evaluating protective clothing materials in testing programs. 1.2 Results derived from testing programs using these lists of challenge chemicals are not intended for the definitive characterization of protective clothing materials. 1.3 This list of challenge chemicals is not inclusive of all chemical challenges; the chemicals were chosen to represent broad ranges of liquid and gaseous chemical classes and properties. Not all chemical classes are represented. Other chemicals, especially those of interest to the manufacturer or user, should be tested in addition to those recommended in this guide.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific hazards statement is given in Section .