坠落防护缓冲器检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 12903-2008个体防护装备术语

本标准规定了个体防护装备术语及定义。本标准适用于有关标准制、修订、技术文件的编制，手册、教材、书刊等的编写和翻译。本标准不适用于医疗救护用个人防护装备。

GB/T 23468-2009坠落防护装备安全使用规范

本标准规定了安全网、安全带等坠落防护装备的配备要求、安全使用要求、使用期限、定期检验要求及标识管理要求。本标准适用于高处作业、攀登及悬吊作业中使用的安全网、安全带等坠落防护装备。本标准不适用于体育运动、消防等用途的坠落防护装备。

GB/T 24537-2009坠落防护带柔性导轨的自锁器

本标准规定了带柔性导轨的自锁器的技术要求、测试方法、检验规则及标识。本标准适用于体重及负重之和不大于100 kg的人员使用的带柔性导轨的自锁器,当使用者的总质量超过100 kg时,应征询制造商的意见,并经测试合格后方可使用。本标准不适用于倾斜角度与垂直方向超过15º的柔性轨道。

GB/T 24538-2009坠落防护缓冲器

本标准规定了缓冲器的分类、技术要求、测试方法、检验规则及标识。本标准适用于体重及负重之和不大于100 kg的人员高处作业、登高及悬吊作业中使用的缓冲器。

GB 24542-2009坠落防护.带刚性导轨的自锁器

本标准规定了带刚性导轨的自锁器的技术要求、测试方法、检验规则及标识。本标准适用于体重及负重之和不大于100kg的人员使用的带刚性导轨的自锁器，当使用者的总质量大于100kg时，应征询制造商的意见，并经测试合格后方可使用。本标准仅适用于垂直方向的导轨。

GB 24543-2009坠落防护.安全绳

本标准规定了安全绳的分类与标记、技术要求、测试方法、检验规则及标识。本标准适用于体重及负重之和不大于100 kg的人员高处作业、登高及悬吊作业中使用的安全绳。本标准不适用于体育运动、消防等用途的安全绳。

GB 24544-2009坠落防护.速差自控器

本标准规定了速差自控器的技术要求、测试方法、检验规则和标识等。本标准适用于高处作业、登高及悬吊作业中体重及负重之和不大于100kg的人员使用的速差器。

GB 30862-2014坠落防护挂点装置

本标准规定了高处坠落防护挂点装置的技术要求、检验方法、检验规则及标识。本标准适用于防护高处坠落的挂点装置。本标准不适用于体育及消防用挂点装置。

NB/T 31052-2014风力发电场高处作业安全规程

本标准规定了风电场进行高处作业的组织管理、人员准备和防护措施等方面的安全要求。本标准适用于陆上风电场运行、维护和检修的高处作业。

DL/T 1475-2015电力安全工器具配置与存放技术要求

本标准规定了电力安全工器具配置、存放的原则及技术要求等。本标准适用于电力安全工器具的配置与存放。

DB50/T 434-2012电梯安装改造维修维保作业安全规范

本标准规定了电梯施工单位安全管理及电梯安装、改造、维修和维保作业方面的安全要求。适用于本市范围内乘客电梯、载货电梯、杂物电梯、液压电梯、自动扶梯与自动人行道的安装、改造、维修和维保作业。

TS EN 355-2004坠落防护. 缓冲器

This standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for energy absorbers

DIN 19703-2014内河航道船闸. 尺寸和设备原理

This standard specifies requirements for dimensions, equipment, construction and design of new-built massive locks for waterways for inland navigation.

DIN 32983-2006轮椅使用者和其他行动不便者用车载升降设备.附加安全要求和试验

This standard is valid together with DIN EN 1756-2 for tail lifts for wheelchair users and for people with reduced mobility. Requirements for e. g. control positions, drive systems and tail lifts, which are not described in DIN EN 1756-2, are specified.#,,#

DIN EN 12312-4-2014航空器地勤支援设备.特殊要求.第4部分:乘客登机桥

This European Standard specifies the technical requirements to minimize the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of passenger boarding bridges (PBBs) when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorized representative. It also takes into account some requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies. This European Standard applies to: a) apron-drive bridges; b) fixed-head bridges (also referred to as nose-loaders) or pedestal bridges; c) suspended bridges, for embarking/disembarking of passengers. It is applicable from the interface with the terminal building, which can be movable, e. g. on two levels to separate arrival and departure level to the connection with the aircraft including fixed tunnels. This European Standard does not apply to: d) elevating lounges; e) passenger stairs; f) other form of aircraft access equipment; g) automatic PBB positioning. This European Standard does not establish requirements for hazards caused by noise and vibration. This part of EN 12312 is not applicable to PBBs which were manufactured before the date of publication of this standard by CEN. This part of EN 12312 when used in conjunction with EN 1915-1, EN 1915-2 and EN 1915-4 provides the requirements for PBBs.

BS 6739-2009过程控制系统仪表的实施规范:安装设计和实施

This British Standard gives recommendations for, and guidance on,the design for the installation of instrumentation of measurementand control systems in the process industry, and the implementationand commissioning of this installation. It is intended to be used asa manual of good practice on the site and also to assist those whodesign the installation.

BS EN 81-43-2009电梯建造和安装的安全规则.载人和载物专用电梯.第43部分:起重机电梯

1.1 This document specifies the safety requirements for the construction and installation of power operatedlifts attached to cranes and intended for access to workplaces on cranes, by authorised persons. This includesintended use, erection, dismantling, inspection and maintenance. The lift serves defined landing levels andhas a load carrying unit which is:a) designed for the transportation of persons and goods;b) guided;c) travelling vertically or along a path within 15 degrees maximum from the vertical;d) supported by rack and pinion or suspended by steel wire ropes;e) travelling with a speed not more than 1,0 m/s for permanent lifts and not more than 0,4 m/s for temporarylifts.1.2 This document identifies hazards as listed in Clause 4 which arise during the various phases in the lifeof such equipment and describes methods for the elimination or reduction of these hazards when used asintended by the manufacturer.1.3 This document does not specify the additional requirements for:a) operation in severe conditions (e.g. extreme climates, strong magnetic fields);b) lightning protection;c) operation subject to special rules (e.g. potentially explosive atmospheres);NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosiveatmospheres can be applicable to the type of machine or equipment covered by this European Standard. The presentstandard is not intended to provide means of complying with the essential health and safety requirements of Directive94/9/EC.d) electromagnetic compatibility (emission, immunity);e) handling of loads the nature of which could lead to dangerous situations;f) the use of combustion engines;g) hydraulic drive units;h) hazards occurring during manufacturing process;i) hazards occurring as a result of being erected over a public road;j) earthquakes;k) noise (see also Directive on noise emissions from machines used outdoors (2000/14/EC)).1.4 This standard is not applicable to:a) builders hoists according to EN 12158-1:2000, EN 12158-2:2000 and EN 12159:2000;b) elevating control stations according to EN 14502-2:2005+A1:2008;c) lifts according to EN 81-1:1998;d) work platforms carried on the forks of fork trucks;e) work platforms;f) funiculars;g) lifts specially designed for military purposes;h) mine lifts;i) theatre elevators.1.5 This standard deals with the complete lift design but excludes the design of the crane. It includes thebase frame and base enclosure but excludes the design of any concrete, hard core, timber or other foundationarrangement. It includes the design of mast ties and the design of anchorage parts between the mast tie andthe crane structure. This standard also includes the design of the landing gates and their fixings.