电解电容器用铝箔检测

发布时间：2024-06-21 作者：中析研究所浏览：

GB/T 3615-2016电解电容器用铝箔

本标准规定了电解电容器用铝箔的要求、试验方法、检验规则和标志、包装、运输、贮存及质量证明书与订货单(或合同)内容。本标准适用于电解电容器用中高压阳极箔、低压阳极箔及阴极箔(以下简称铝箔)。

GB/T 31845-2015电工电子设备机械结构热设计规范

本标准规定了电工电子设备机械结构热设计的基本原则、热设计要求、常用散热技术、关键散热部件、导热界面材料以及热测试的相关要求，同时在附录中介绍了热设计算法和常用材料的物理参数。本标准适用于除手持终端以外所有电工电子设备机械结构的热设计。以下电工电子设备简称“设备”，电工电子设备机械结构简称“机械结构”。

SJ/T 10557.1-2022电解电容器用铝箔技术条件

本文件规定了电解电容器用铝箔的技术要求，试验方法，检验规则及标志、包装、运输和贮存。本文件适用于高压电解电容器用阳极箔(以下简称高压原箔)，低压电解电容器用阳极箔(以下简称低压原箔)和电解电容器用阴极箔(以下简称阴极箔)。

SJ/T 10557.2-1994高压电解电容器用铝箔晶粒织构测量方法

本标准规定了高压电解电容器用铝箔的织构测量方法。本标准适用于高压电解电容器用铝箔。

SJ/T 10557.3-1994电解电容器用铝箔平均位错密度测量方法

本标准规定了电解电容器用铝箔平均位错密度的测量方法。本方法适用于平均位错密度为0～9×10^(6)个cm^(2)的电解电容器用铝箔。

SJ/T 10557.4-1994电解电容器用铝箔化学分析方法原子吸收分光光度法测定铜、铁、锌、锰、和镁量

本标准规定了电解电容器用铝箔中铜、铁、锌、锰和镁的测定。本标准适用于下列含量范围的电解电容器用铝箔：铜含量：0.0005～0.2000％；铁含量：0.001～0．200%；锌含量：0.0005～0．0200％；锰含量：0．0002～0．2000％；镁含量：0．0001～0．0250%。

UL 399-2008饮用水冷却器

1.1 These requirements cover self-contained drinking-water coolers which employ hermetic refrigerantmotor-compressors and which are designed for connection to alternating-current circuits rated not greaterthan 600 volts in accordance with the National Electrical Code, NFPA 70. The requirements also apply towater coolers which supply both hot and cold water.1.2 These requirements do not include additional requirements applicable to equipment designed for usein hazardous locations as defined in the National Electrical Code, NFPA 70.1.3 A product that contains features, characteristics, components, materials, or systems new or differentfrom those covered by the requirements in this standard, and that involves a risk of fire, electric shock, orinjury to persons shall be evaluated using the appropriate additional component and end-productrequirements as determined necessary to maintain the acceptable level of safety as originally anticipatedby the intent of this standard. A product whose features, characteristics, components, materials, orsystems conflict with specific requirements or provisions of this standard cannot be judged to comply withthis standard. Where considered appropriate, revision of requirements shall be proposed and adopted inconformance with the methods employed for development, revision, and implementation of this standard.

UL 935-2001荧光灯镇流器

1.1 These requirements cover ballasts of the resistance, reactance, and electronic (high frequency) types for use with fluorescent lamps involving a potential of 2500 volts or less in accordance with the National Electrical Code, ANSI/NFPA 70.1.2 A fluorescent-lamp ballast may be determined by investigation to be acceptable for use, in a fixtureor other device, with electric-discharge lamps of other than the fluorescent type.1.3 Fluorescent self ballasted lamps and ballast adaptors are evaluated using the Standard forSelf-Ballasted Lamps and Lamp Adapters, UL 1993. The component ballast is evaluated to requirementsin this Standard.1.4 A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire or of electric shockor injury to persons shall be evaluated using appropriate additional component and end-productrequirements to maintain the level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

DIN EN 61360-4-2005电子元器件标准数据元素类型和相关分类模式.第4部分:IEC标准数据元素类型和元器件分类的基准集

This standard specifies:-the definitions of data element types for electric components and materials used in electrotechnical equipment and systems;-the definitions of the component classes with associated classification scheme